Pinecil not working
#3
(01-16-2021, 06:04 AM)Ralim Wrote:
(01-15-2021, 07:51 PM)psychedup Wrote:
  • If I leave it unplugged for a while (like 10 minutes or so) and then plug it into the PBP, in dmesg I see something like:
    [  +1.360001] usb 2-1-port1: Cannot enable. Maybe the USB cable is bad?[  +0.000384] usb 2-1-port1: attempt power cycle(but not the usual message with the USB vendor/device id's like it showed earlier)
  • If I hold down "-" while plugging it in, nothing shows up at all.
I wonder if that means it is "soft bricked"? I assume I would need the breakout board to recover from that, but is there any way for me to confirm that it's not a hardware problem first? Or what would be the next logical troubleshooting step?


(1) This is normal as the main firmware does not implement USB (so the computer will see no response).
(2) The bootloader that you trigger with the "-" is burned into the rom of the MCU so you can erase it (as far as I'm aware).

I would suggest trying a different cable / port if you can first (as some cables are not amazing quality, and the mcu isnt amazing usb driving either i suspect).
Also, try holding the "-" when you plug it in, and then continue to hold it for 10 seconds or so. On some devices I have found that it can take a bit for the ROM to initalise and set itself up correctly.

I have found it helpful to run dmesg -wH to watch dmesg while i connect the unit so i can see whats going on.

Yeah dmesg -Hw is what I have been watching. I've tried at least 3 different cables, on multiple PC's/SBC's/ports. They seem to detect that something was plugged in, but nothing else shows up, even if I keep "-" held down for 60 seconds. And of course "dfu-util -l" doesn't find anything.
  Reply


Messages In This Thread
Pinecil not working - by psychedup - 01-15-2021, 07:51 PM
RE: Pinecil not working - by Ralim - 01-16-2021, 06:04 AM
RE: Pinecil not working - by psychedup - 01-16-2021, 11:35 AM
RE: Pinecil not working - by Ralim - 01-16-2021, 06:48 PM
RE: Pinecil not working - by psychedup - 01-16-2021, 08:33 PM

Possibly Related Threads…
Thread Author Replies Views Last Post
  Crippling noise from inside pinecil during a few minutes high power soldering. dreieck 3 2,563 05-15-2025, 10:41 AM
Last Post: dreieck
  Pinecil v2 issue autumnharris 0 187 05-15-2025, 01:35 AM
Last Post: autumnharris
  Pinecil V2 doesn’t power on under any circumstances BigCarrotLeaf 0 615 03-22-2025, 07:29 AM
Last Post: BigCarrotLeaf
  Pinecil constantly cutting out WroughtIron 1 1,105 01-16-2025, 02:20 AM
Last Post: D4veC4rter
Exclamation Pinecil is working with 5v but nothing else!! MizterPink 1 579 01-07-2025, 03:59 PM
Last Post: MizterPink
  Pinepower suitable for an s23 (and a pinecil) its_lieseeeee 0 499 12-09-2024, 01:41 PM
Last Post: its_lieseeeee
  Help with Pinecil saranelson 1 775 11-09-2024, 02:19 PM
Last Post: biketool
  pinecil v2 reverse polarity issue adamsk1952 0 830 09-12-2024, 07:54 AM
Last Post: adamsk1952
Sad Pinecil V2 screw broken! Carol8 1 790 09-09-2024, 08:44 AM
Last Post: Carol8
  Pinecil on Amazon? WEF 5 3,192 09-05-2024, 08:23 AM
Last Post: Jeb

Forum Jump:


Users browsing this thread: 1 Guest(s)