Any hope for PineTime.
#1
My PineTime is stuck on the InfiniTime triangles after trying to install the latest update 1.9.0. That got to 1% install and dropped the connection. The first restart got back to the normal watch screen so I tried again with the same result. Now holding the power button in gets the green Pine then just boots to InfiniTime screen. Have tried oldr updates which get to 2% before the connection is dropped, have left it for a couple of days tom drain with the same result. Holding the power button for longer just cycles through red green amd blue pines but ends at the same place. This is a sealed version and the hard reset has always worked before when stuck on InfiniTime screen. All update had been validated. Any hints on what to try next.
  Reply
#2
I get to 13% and it starts again. The bootloader zip hs a similar problem.
  Reply
#3
Question 
@lakotaubp, could you provide more details?
what the application is used for update (Gadgetbridge / nRF Connect / Siglo / Amazfish)? 
what was the previous version of the InfiniTime that worked?
what exactly "InfiniTime triangles" are: with "infini time" text and 2 triangles, or pine-like triangles and no text?
[Image: Flash-infinitime.jpg]
Away
  Reply
#4
(04-21-2022, 04:22 AM)ITCactus Wrote: @lakotaubp, could you provide more details?
what the application is used for update (Gadgetbridge / nRF Connect / Siglo / Amazfish)? 
what was the previous version of the InfiniTime that worked?
what exactly "InfiniTime triangles" are: with "infini time" text and 2 triangles, or pine-like triangles and no text?
[Image: Flash-infinitime.jpg]

The PineTime was all upto date on OS and software. I tried both Gadgetbridge and nRF Connect. The screen it sticks on is the two triangles InfiniTime. When holding the button in for approx 10 sec it goes to the green pinecone when that has finished then it is back to the InfiniTime screen. I will try again tomorrow. For now I am leaving it in a drawer for a few days to completly discharge.
  Reply
#5
(04-23-2022, 05:23 AM)lakotaubp Wrote:
(04-21-2022, 04:22 AM)ITCactus Wrote: @lakotaubp, could you provide more details?
what the application is used for update (Gadgetbridge / nRF Connect / Siglo / Amazfish)? 
what was the previous version of the InfiniTime that worked?
what exactly "InfiniTime triangles" are: with "infini time" text and 2 triangles, or pine-like triangles and no text?
[Image: Flash-infinitime.jpg]

The PineTime was all upto date on OS and software. I tried both Gadgetbridge and nRF Connect. The screen it sticks on is the two triangles InfiniTime. When holding the button in for approx 10 sec it goes to the green pinecone when that has finished then it is back to the InfiniTime screen. I will try again tomorrow. For now I am leaving it in a drawer for a few days to completly discharge.
 
if i remember correctly, the boot screen with "infini time" text and 2 triangles indicates an old bootloader, and you should first update the latest bootloader "reloader-mcuboot.zip" from this wiki page.

also, there is a known issue for some users on update from 1.8 to 1.9 using nRF Connect.

and, in the end, this answer by JF could be helpful.

if you stuck in InfiniTime triangles with "infini time" text and 2 triangles, maybe my experience may be helpful - just try from the step#2 to the end.
Away
  Reply
#6
(04-23-2022, 06:45 AM)ITCactus Wrote:
(04-23-2022, 05:23 AM)lakotaubp Wrote:
(04-21-2022, 04:22 AM)ITCactus Wrote: @lakotaubp, could you provide more details?
what the application is used for update (Gadgetbridge / nRF Connect / Siglo / Amazfish)? 
what was the previous version of the InfiniTime that worked?
what exactly "InfiniTime triangles" are: with "infini time" text and 2 triangles, or pine-like triangles and no text?
[Image: Flash-infinitime.jpg]

The PineTime was all upto date on OS and software. I tried both Gadgetbridge and nRF Connect. The screen it sticks on is the two triangles InfiniTime. When holding the button in for approx 10 sec it goes to the green pinecone when that has finished then it is back to the InfiniTime screen. I will try again tomorrow. For now I am leaving it in a drawer for a few days to completly discharge.
 
if i remember correctly, the boot screen with "infini time" text and 2 triangles indicates an old bootloader, and you should first update the latest bootloader "reloader-mcuboot.zip" from this wiki page.

also, there is a known issue for some users on update from 1.8 to 1.9 using nRF Connect.

and, in the end, this answer by JF could be helpful.

if you stuck in InfiniTime triangles with "infini time" text and 2 triangles, maybe my experience may be helpful - just try from the step#2 to the end.

Retried today with GadgetBridge which worked update installed Smile  PineTime back in action. Thanks for the advice.
  Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  PineTime Touch Screen Stopped Working BlunderingBushcraft 3 531 07-30-2022, 04:19 PM
Last Post: headgr
  Pinetime stuck at infinitime logo monto 2 227 07-30-2022, 06:16 AM
Last Post: kng
  can anyone suggest their working Linux bluetooth USB dongles to connect to Pinetime? jahway603 4 194 07-27-2022, 07:38 PM
Last Post: jahway603
  Pinetime almost dead... only shows Infinitime logo. lightweight 6 1,325 06-18-2022, 03:21 AM
Last Post: bboett
  Any plans for a revised PineTime? nixcamic 0 473 05-16-2022, 11:14 AM
Last Post: nixcamic
Question What can/can't I do with a PineTime smart watch (sealed)? danimations 7 1,679 04-16-2022, 07:18 AM
Last Post: _slowmanship_
Question [question] how to restore PineTime to a factory state after flashing non-OTA/directly ITCactus 2 582 04-11-2022, 05:03 AM
Last Post: ITCactus
  Will the PineTime have a timer for the Pomodoro technique? bosi564 3 941 04-05-2022, 03:28 AM
Last Post: ITCactus
Lightbulb Saving, loading, sending and receiving images via Bluetooth to and from Pinetime danimations 0 340 03-29-2022, 01:21 AM
Last Post: danimations
Question Which companion apps work best for flashing firmware and pairing/syncing w/ Pinetime? danimations 0 421 03-28-2022, 08:22 PM
Last Post: danimations

Forum Jump:


Users browsing this thread: 1 Guest(s)