I am working on getting tow-boot to work on my PPP. I can get it installed, but when I boot it up afterwards it will turn the red LED on, and do the vibes thing, then turn yellow and four vibes, it waits a bit before flashing and vibrating like 10 times, then it seems to turn off. Holding down the up volume it acts similarly but turns the light blue first, before turning red and blinking.vibing a few times, pausing, then doing the ten vibe blink thing and turning off. If its on a charger, it just keeps looping that. If it's attached to a computer it never gets recognized, just loops like on a charger. I have gone through the tow-boot several times, watched videos, paid very close attention to detail and it does it every time. I erased the SPI before installing, and same thing.
I just got the phone this weekend if that helps any. It was running ok with the default manjaro plasma, I did run manjaro phosh off an SD and attempted to install it to emmc, it took forever and I thought it failed/stalled but eventually it said it completed it. It would not boot off it though. In the meantime I was researching stuff and came across tow-boot as the thing to do to make swapping OSes easier so I went for it and here we are.
Any ideas would be great. Thanks.
(02-15-2023, 03:02 PM)techariah Wrote: I am working on getting tow-boot to work on my PPP. I can get it installed, but when I boot it up afterwards it will turn the red LED on, and do the vibes thing, then turn yellow and four vibes, it waits a bit before flashing and vibrating like 10 times, then it seems to turn off. Holding down the up volume it acts similarly but turns the light blue first, before turning red and blinking.vibing a few times, pausing, then doing the ten vibe blink thing and turning off. If its on a charger, it just keeps looping that. If it's attached to a computer it never gets recognized, just loops like on a charger. I have gone through the tow-boot several times, watched videos, paid very close attention to detail and it does it every time. I erased the SPI before installing, and same thing.
I just got the phone this weekend if that helps any. It was running ok with the default manjaro plasma, I did run manjaro phosh off an SD and attempted to install it to emmc, it took forever and I thought it failed/stalled but eventually it said it completed it. It would not boot off it though. In the meantime I was researching stuff and came across tow-boot as the thing to do to make swapping OSes easier so I went for it and here we are.
Any ideas would be great. Thanks.
additional info/update. I flashed the postmarket installer to an SD card, booted off that, did the install and everything looked fine. Removed the Sd card and in it's behaving the same as above. Maybe I misunderstood "installer?" Just tried to boot back off the SD and it seems to work there, so I guess I did misunderstand that. Also of note, when I hold volume down on boot, it does turn the LED teal like tow-boot says.
Well, after continued research I finally found a post that addressed the issue. Evidently that first move to flash the emmc that failed was the culprit. tow boot must have a functional OS on the emmc to work properly. I went back and ran manjaro phosh of the SD, downloaded it on the phone, expanded it, ran dd to write to emmc and now tow-boot works. At least it is not rebooting and I am able to connect it to the computer via usb and and currently flashing directly.
(02-16-2023, 02:50 PM)techariah Wrote: Well, after continued research I finally found a post that addressed the issue. Evidently that first move to flash the emmc that failed was the culprit. tow boot must have a functional OS on the emmc to work properly. I went back and ran manjaro phosh of the SD, downloaded it on the phone, expanded it, ran dd to write to emmc and now tow-boot works. At least it is not rebooting and I am able to connect it to the computer via usb and and currently flashing directly.
Thats interesting, also THANK YOU, also wtf tow-boot?? I've been trying to figure out whats going on for 3 days as my phone wont let me do anything but SD boot. ive been TRYING to use tow-boot to flash the emmc from clean but apparently thats not an option. But after booting postmarket and writing itself to itself, seems good. i feel like requiring a good emmc to flash emmc is a bit of an oversight..
(12-04-2024, 09:15 AM)Blackheart Wrote: (02-16-2023, 02:50 PM)techariah Wrote: Well, after continued research I finally found a post that addressed the issue. Evidently that first move to flash the emmc that failed was the culprit. tow boot must have a functional OS on the emmc to work properly. I went back and ran manjaro phosh of the SD, downloaded it on the phone, expanded it, ran dd to write to emmc and now tow-boot works. At least it is not rebooting and I am able to connect it to the computer via usb and and currently flashing directly.
Thats interesting, also THANK YOU, also wtf tow-boot?? I've been trying to figure out whats going on for 3 days as my phone wont let me do anything but SD boot. ive been TRYING to use tow-boot to flash the emmc from clean but apparently thats not an option. But after booting postmarket and writing itself to itself, seems good. i feel like requiring a good emmc to flash emmc is a bit of an oversight..
in pinephone regular, tow-boot is installed on internal memory emmc.
in pp pro, tow-boot is installed on spi memory, which is separate from both emmc and sdcard.
hence, regular and pro have different installers. and my guess is that boot code is also sightly different.
do you have tow-boot in emmc mem in pp pro !?
|
tow-boot installation problem
