Defective? PCI-E -> SATA card no work good

[Bullet64]

Hi,

my board v2.1 is running with bionic-minimal. I don't use any desktop systems atm, too many bugs. Please inform me, when its run well

Code:

rock64@rockpro64v2_1:~$ uname -a Linux rockpro64v2_1 4.4.138-1094-rockchip-ayufan-gf13a8a9a4eee #1 SMP Thu Aug 9 20:29:55 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux

dmesg

Code:

rock64@rockpro64v2_1:~$ dmesg | grep -E pcie [    0.506998] of_get_named_gpiod_flags: parsed 'gpio' property of node '/vcc3v3-pcie-regulator[0]' - status (0) [    0.507045] reg-fixed-voltage vcc3v3-pcie-regulator: Looking up vin-supply from device tree [    0.507084] vcc3v3_pcie: supplied by dc_12v [    0.507136] vcc3v3_pcie: 3300 mV [    0.507304] reg-fixed-voltage vcc3v3-pcie-regulator: vcc3v3_pcie supplying 3300000uV [    2.868298] vcc3v3_pcie: disabling [    3.171478] phy phy-pcie-phy.9: Looking up phy-supply from device tree [    3.171482] phy phy-pcie-phy.9: Looking up phy-supply property in node /pcie-phy failed [    3.278691] rockchip-pcie f8000000.pcie: GPIO lookup for consumer ep [    3.278715] rockchip-pcie f8000000.pcie: using device tree for GPIO lookup [    3.278812] of_get_named_gpiod_flags: parsed 'ep-gpios' property of node '/pcie@f8000000[0]' - status (0) [    3.279319] rockchip-pcie f8000000.pcie: Looking up vpcie3v3-supply from device tree [    3.279493] rockchip-pcie f8000000.pcie: Looking up vpcie1v8-supply from device tree [    3.279515] rockchip-pcie f8000000.pcie: Looking up vpcie1v8-supply property in node /pcie@f8000000 failed [    3.279564] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found [    3.289691] rockchip-pcie f8000000.pcie: Looking up vpcie0v9-supply from device tree [    3.289716] rockchip-pcie f8000000.pcie: Looking up vpcie0v9-supply property in node /pcie@f8000000 failed [    3.289776] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found [    3.299851] rockchip-pcie f8000000.pcie: invalid power supply [    3.848058] PCI host bridge /pcie@f8000000 ranges: [    3.875577] rockchip-pcie f8000000.pcie: PCI host bridge to bus 0000:00 [    3.905032] pcieport 0000:00:00.0: enabling device (0000 -> 0002) [    3.905397] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt [    3.905408] pcie_pme 0000:00:00.0:pcie01: service driver pcie_pme loaded [    3.905516] aer 0000:00:00.0:pcie02: service driver aer loaded

lspci

Code:

rock64@rockpro64v2_1:~$ sudo lspci -vvv [sudo] password for rock64: 00:00.0 PCI bridge: Rockchip Inc. RK3399 PCI Express Root Port Device 0100 (prog-if 00 [Normal decode])     Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+     Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx-     Latency: 0     Interrupt: pin A routed to IRQ 238     Bus: primary=00, secondary=01, subordinate=01, sec-latency=0     I/O behind bridge: 00000000-00000fff     Memory behind bridge: fa000000-fa0fffff     Prefetchable memory behind bridge: 00000000-000fffff     Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-     BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-         PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-     Capabilities: [80] Power Management version 3         Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)         Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME+     Capabilities: [90] MSI: Enable+ Count=1/1 Maskable+ 64bit+         Address: 00000000fee30040  Data: 0000         Masking: 00000000  Pending: 00000000     Capabilities: [b0] MSI-X: Enable- Count=1 Masked-         Vector table: BAR=0 offset=00000000         PBA: BAR=0 offset=00000008     Capabilities: [c0] Express (v2) Root Port (Slot+), MSI 00         DevCap:    MaxPayload 256 bytes, PhantFunc 0             ExtTag- RBE+         DevCtl:    Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+             RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+             MaxPayload 128 bytes, MaxReadReq 512 bytes         DevSta:    CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-         LnkCap:    Port #0, Speed 5GT/s, Width x4, ASPM L1, Exit Latency L0s <256ns, L1 <8us             ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+         LnkCtl:    ASPM Disabled; RCB 64 bytes Disabled- CommClk-             ExtSynch- ClockPM- AutWidDis- BWInt+ AutBWInt+         LnkSta:    Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-         SltCap:    AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-             Slot #0, PowerLimit 0.000W; Interlock- NoCompl-         SltCtl:    Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-             Control: AttnInd Off, PwrInd Off, Power+ Interlock-         SltSta:    Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock-             Changed: MRL- PresDet- LinkState-         RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-         RootCap: CRSVisible-         RootSta: PME ReqID 0000, PMEStatus- PMEPending-         DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via message ARIFwd+         DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-         LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-              Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-              Compliance De-emphasis: -6dB         LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-              EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-     Capabilities: [100 v2] Advanced Error Reporting         UESta:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-         UEMsk:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-         UESvrt:    DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-         CESta:    RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-         CEMsk:    RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+         AERCap:    First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-     Capabilities: [274 v1] Transaction Processing Hints         Interrupt vector mode supported         Device specific mode supported         Steering table in TPH capability structure     Kernel driver in use: pcieport 01:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 02) (prog-if 01 [AHCI 1.0])     Subsystem: ASMedia Technology Inc. ASM1062 Serial ATA Controller     Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+     Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-     Latency: 0     Interrupt: pin A routed to IRQ 239     Region 0: I/O ports at <unassigned> [disabled]     Region 1: I/O ports at <unassigned> [disabled]     Region 2: I/O ports at <unassigned> [disabled]     Region 3: I/O ports at <unassigned> [disabled]     Region 4: I/O ports at <unassigned> [disabled]     Region 5: Memory at fa010000 (32-bit, non-prefetchable) [size=512]     [virtual] Expansion ROM at fa000000 [disabled] [size=64K]     Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-         Address: fee30040  Data: 0000     Capabilities: [78] Power Management version 3         Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)         Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-     Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00         DevCap:    MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us             ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-         DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- Unsupported-             RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+             MaxPayload 128 bytes, MaxReadReq 512 bytes         DevSta:    CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-         LnkCap:    Port #1, Speed 5GT/s, Width x1, ASPM not supported, Exit Latency L0s unlimited, L1 <2us             ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-         LnkCtl:    ASPM Disabled; RCB 64 bytes Disabled- CommClk-             ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-         LnkSta:    Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-         DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR-, OBFF Not Supported         DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled         LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-              Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-              Compliance De-emphasis: -6dB         LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-              EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-     Capabilities: [100 v1] Virtual Channel         Caps:    LPEVC=0 RefClk=100ns PATEntryBits=1         Arb:    Fixed- WRR32- WRR64- WRR128-         Ctrl:    ArbSelect=Fixed         Status:    InProgress-         VC0:    Caps:    PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-             Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-             Ctrl:    Enable+ ID=0 ArbSelect=Fixed TC/VC=ff             Status:    NegoPending- InProgress-     Kernel driver in use: ahci

I am using three HDD/SDD's

Code:

rock64@rockpro64v2_1:~$ df -h Filesystem      Size  Used Avail Use% Mounted on udev            992M     0  992M   0% /dev tmpfs           200M  484K  199M   1% /run /dev/sda7       235G  106G  120G  47% / tmpfs           996M     0  996M   0% /dev/shm tmpfs           5,0M  4,0K  5,0M   1% /run/lock tmpfs           996M     0  996M   0% /sys/fs/cgroup /dev/sda6       112M  4,0K  112M   1% /boot/efi /dev/sdb1       932G  128G  803G  14% /mnt /dev/sdc3       1,2G  1,2G     0 100% /media tmpfs           200M     0  200M   0% /run/user/1000

sda = USB3 SSD Samsung Pro 256GB
sdb = SATA 1TB HDD
sdc = SATA 250GB SSD (ipfire image = 2GB - i know)

uptime

rock64@rockpro64v2_1:~$ uptime
 16:55:05 up 20:08,  1 user,  load average: 0,00, 0,00, 0,00

Only problem i know is that usb3 isn't stable atm.