Welcome, Guest
You have to register before you can post on our site.
Forum Statistics
» Members: 29,705» Latest member: Sheo » Forum threads: 16,261» Forum posts: 117,195
Full Statistics
Latest Threads
Quill OS for the PineNote PineNote Software Last Post: JhonSmith 9 hours ago » Replies: 1» Views: 70
PinePhone, PinePhone Pro,... PinePhone Hardware Last Post: biketool 10 hours ago » Replies: 3» Views: 175
auto-owning the SD card i... PineTab Software Last Post: biketool Yesterday , 04:16 AM» Replies: 1» Views: 385
Old Danctnix server in Pa... PineTab Software Last Post: Stunnned » Replies: 2» Views: 195
Volumio (PINE A64-LTS / S... Linux on PINE A64-LTS / SOPINE Last Post: kapqa » Replies: 8» Views: 15,548
Reinstallation Arch Linux... General Discussion on PineTab Last Post: rth » Replies: 1» Views: 236
Recycling pinephone as ho... PinePhone Hardware Last Post: biketool » Replies: 5» Views: 642
Light Sensor / Proximity ... General Discussion on PinePhone Last Post: WhiteHexagon » Replies: 1» Views: 222
How to stop it turning on General Discussion on PinePhone Last Post: biketool » Replies: 3» Views: 496
8/24 status of JumpDrive PinePhone Software Last Post: biketool » Replies: 5» Views: 2,201
NVME problems
Posted by: mamboman777 - 07-14-2020, 09:10 PM - Forum: General Discussion on Pinebook Pro
- Replies (12)
Well, I took my Intel 660p to my brother's house and put it in his windows box and it was working, firmware updated, and showing nothing wrong. When I dropped it back in my Pinebook Pro...nothing. So I decided to investigate some and completely took out the main board of the PBP. After reassembling I booted and the NMVe was there! Drove back home and the NVMe is no longer listed as a drive. Any idea what's going on? So, I now know, it's not the NVME's fault. I guess next I buy a new adapter or cable? If that doesn't work, then what? Main board?
Video output scale after update 14/07/2020
Posted by: antiX-Dave - 07-14-2020, 05:13 PM - Forum: Mobian on PinePhone
- Replies (3)
The video scaled output has changed in the last update on my phone.
Ubports edition shows nothing on screen after liquid exposure
Posted by: partytax - 07-14-2020, 05:12 PM - Forum: PinePhone Hardware
- Replies (5)
I've been using my PinePhone Ubports edition with much success for the last few weeks, but last night I think it was exposed to too much liquid. I laid out a bunch of things from my backpack and sprayed bleach cleaner over them (because the plague). After I dried things off, I tried to charge and boot my PinePhone (stupid, I know) and all I got to was a backlit black screen. The backlight turned on and off a few times pretty systematically. I typically use Mobian, but I tried booting into Ubports as well. Nothing...not even the Pine64 logo showed up. When I insert or remove the USB cable, however, the phone plays a clicking sound effect, which makes me think the thing might not be completely dead. Not sure if this matters, but the phone was in a pretty hot environment for the preceding hour and AFAIK had exhausted its battery when I cleaned it.
i2c0 transfers cause bus errors
Posted by: michaelanburaj - 07-14-2020, 02:25 PM - Forum: Linux on Rock64
- No Replies
Hello,the rock64 i2c-0 when trying to quick check discover connected devices (quick read, byte read, both), does send on occasions following the NACKed address byte a 2nd start condition and stop immediately, then another 3rd start before next transfer [see the attachment], that starts with the next device address. the additional 2nd start before the stop is bothering a STM32 slave sitting on this bus (additional data point a LPC controller does not get affected). While he STM32 seems sensitive to such errors (BERR) and causes lock-up, I am interested in knowing why does the rock64 do this. the bus is run at 100KHz, i even tried adding a delay in the loops for 100ms, still does not help. is there a setting in device tree or in rockchip's i2c registers to prevent this from happening? If this is not normal could some other hardware/software muxed on the port pins be causing this? [attachment: 1 NACKd-address in the capture is a normal one, that ends with a stop and the next start condition starts the next transfer. the 2nd NACKd-address ends with a added 2nd start, then stop, followed by a start for the next transfer] Thanks, -Michael.
Attached Files i2c-inserted 2nd start.png (Size: 116.65 KB / Downloads: 412)
Enable I2C to interface with PCA9685
Posted by: Stoovurt - 07-14-2020, 02:13 PM - Forum: RockPro64 Hardware and Accessories
- No Replies
After downloading and installing the latest Adafruit drivers for the PCA9685 (https://github.com/adafruit/Adafruit_Python_PCA9685 ), I attempted to run the provided examples/simpletest.py script, which got this output:
FDE
Posted by: GloriousCoffee - 07-14-2020, 11:05 AM - Forum: Mobian on PinePhone
- Replies (4)
Hi
Cross-compiling Rust for Pinephone
Posted by: ElusivePine - 07-14-2020, 10:52 AM - Forum: General Discussion on PinePhone
- Replies (5)
Hello,
Code:
= note: /usr/lib/gcc/aarch64-linux-gnu/10.1.0/../../../../aarch64-linux-gnu/bin/ld: cannot find -lgtk-3
What should i pack in the box with my v2.2. clusterboard?
Posted by: timoc - 07-14-2020, 10:34 AM - Forum: Clusterboard
- Replies (3)
i stumbled across an old clusterboard i bought for a defunct project, back when there was a promtion to get a SoPine bundled with it . https://forum.pine64.org/showthread.php?...0#pid49660
