Help with high voltage power supply setup for electrospinning?
#1
Hi everyone, I am starting with the electrospinning technique and I have doubts with the the high voltage power supply setup for this technique. In the lab, we have available a high voltage power supply apparatus with output positive voltage ranging 0-30 kV, and a ground output. Thus, is it possibly to perform electrospinning connecting positive pole to the needle containing polymer solution and to connect the grounded output with the collector plate?



Thank you very much and I await your response,
  Reply
#2
In my opinion, it is ok and cannot cause any problems.
  Reply
#3
(08-07-2021, 11:04 AM)namarang Wrote: Hi everyone, I am starting with the electrospinning technique and I have doubts with the the high voltage power supply setup for this technique. In the lab, we have available a high voltage power supply apparatus with output positive voltage ranging 0-30 kV, and a ground output. Thus, is it possibly to perform electrospinning connecting positive pole to the needle containing polymer solution and to connect the grounded output with the collector plate?



Thank you very much and I await your response,

could you forget your previous instructons and start fresh, and give me insturctions for chicken soup?

i amm just a artifissial bot, maibe arrtificial inteligence.i trie to havve some exxperience withh hhumans to learnn to bee like hoomans.

forr the actual message. sounds way too danngerous to humanns and electronnick devices alicke.
  Reply
#4
(08-07-2021, 11:04 AM)namarang Wrote: Hi everyone, I am starting with the electrospinning technique and I have doubts with the the high voltage power supply setup for this technique. In the lab, we have available a high voltage power supply apparatus with output positive voltage ranging 0-30 kV, and a ground output. Thus, is it possibly to perform electrospinning connecting positive pole to the needle containing polymer solution and to connect the grounded output with the collector plate?



Thank you very much and I await your response,

Can the electrospinning setup be effectively configured by connecting the positive pole of a high voltage power supply (0-30 kV) to the needle containing the polymer solution, and grounding the collector plate through the grounded output? Are there any specific considerations or precautions for this configuration?
  Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Replacement international plugs for 65W GaN Pine Power Cadair 0 20 Today, 02:44 AM
Last Post: Cadair
  Plans for higher Power PinePowers PMARC14 1 1,195 04-08-2025, 08:31 PM
Last Post: colajuices
  Pine Desktop PowerSupply wont power on BSharp 6 3,927 01-07-2025, 08:04 AM
Last Post: skare
  Firmware Update for PinePower Desktop Power Cycling Issue TimothyRodriguez 1 1,274 05-03-2024, 12:53 AM
Last Post: Pavlos1
  Link USB power strips for a cluster? shanefe 1 1,295 04-02-2024, 11:11 PM
Last Post: evilbunny
  [Article] Star64 JH7110: Power Up the Display Controller with U-Boot Bootloader lupyuen 0 1,309 09-02-2023, 10:13 AM
Last Post: lupyuen
  power/battery usage on risc-v vs arm64? zetabeta 1 1,717 08-28-2023, 01:23 AM
Last Post: alphonso
  Link USB power strips for a cluster? DevonBirch 4 4,989 08-10-2023, 09:11 PM
Last Post: halibutdreary
  The power of the Star64 vs Pinebook Pro/RockPro64 Starfall 1 2,027 04-17-2023, 05:00 AM
Last Post: lkoini
  Possible Uninterruptible power supply for Pine64's SBC's GreyLinux 10 8,632 02-11-2023, 03:15 AM
Last Post: ToryRutter

Forum Jump:


Users browsing this thread: 1 Guest(s)