DOA Pinecil?
#1
My Pinecil arrived this morning and it doesn't seem to be working.

When I power it up, the main screen pops up and I can go through the menus, but as soon as I try to turn the heat on, it blinks off and then restarts.

I tried updating the firmware, but got an error message when I tried to flash it:


Invalid DFU suffix signature A valid DFU suffix will be required in a future dfu-util release!!! Error during special command "MASS_ERASE" get_status 
DFU-Util exited with error code 74!
Flashing failed.


Any suggestions on how to get it working?
  Reply
#2
(01-26-2021, 08:30 PM)foobarney Wrote: My Pinecil arrived this morning and it doesn't seem to be working.

When I power it up, the main screen pops up and I can go through the menus, but as soon as I try to turn the heat on, it blinks off and then restarts.

I tried updating the firmware, but got an error message when I tried to flash it:


Invalid DFU suffix signature A valid DFU suffix will be required in a future dfu-util release!!! Error during special command "MASS_ERASE" get_status 
DFU-Util exited with error code 74!
Flashing failed.


Any suggestions on how to get it working?

Please make sure that your power supply is not under power and trigger self protection when pinecil try to heat up.

For DFU error, please visit this thread: https://github.com/Ralim/IronOS/issues/820[url=https://github.com/Ralim/IronOS/issues/820][/url]
  Reply
#3
(01-27-2021, 04:19 PM)tllim Wrote:
(01-26-2021, 08:30 PM)foobarney Wrote: My Pinecil arrived this morning and it doesn't seem to be working.

When I power it up, the main screen pops up and I can go through the menus, but as soon as I try to turn the heat on, it blinks off and then restarts.

I tried updating the firmware, but got an error message when I tried to flash it:


Invalid DFU suffix signature A valid DFU suffix will be required in a future dfu-util release!!! Error during special command "MASS_ERASE" get_status 
DFU-Util exited with error code 74!
Flashing failed.


Any suggestions on how to get it working?

Please make sure that your power supply is not under power and trigger self protection when pinecil try to heat up.

For DFU error, please visit this thread: https://github.com/Ralim/IronOS/issues/820[url=https://github.com/Ralim/IronOS/issues/820][/url]
  Reply
#4
I checked with multiple power supplies--when I plug in a 12V supply the little numbers on the right of the display ramp up to 12; when I plug in a 60W USB-C PD supply, they ramp up to 20. So I don't think the Pinecil thinks it's undervolted.

And I don't think the power connector is loose, because it works fine in the menus; it only happens when I go to solder.

I tried pulling out and reseating the tip just to confirm that it wasn't the problem--no change.
  Reply
#5
(01-27-2021, 10:17 PM)foobarney Wrote: I checked with multiple power supplies--when I plug in a 12V supply the little numbers on the right of the display ramp up to 12; when I plug in a 60W USB-C PD supply, they ramp up to 20. So I don't think the Pinecil thinks it's undervolted.

And I don't think the power connector is loose, because it works fine in the menus; it only happens when I go to solder.

I tried pulling out and reseating the tip just to confirm that it wasn't the problem--no change.

If the unit is tripping off as soon as you attempt to heat the tip this is most likely a poor power supply or a bad tip.
  Reply
#6
[quote pid='88457' dateline='1611829297']


If the unit is tripping off as soon as you attempt to heat the tip this is most likely a poor power supply or a bad tip.
[/quote]

Ive tried multiple power supplies (both barrels and usb-c), so that seems an unlikely culprit.

Unfortunately, I don't have another tip to test with.

Would there be a log somewhere I could dump?

If it's the tip, how do I go about replacing it? I haven't seen any RMA/support info on Pine's website.


Thank you!
  Reply
#7
I tried the USB-PD with another cable and it seems to be working.

Not sure why the barrel connector did the same thing, though. I'm looking for another high-enough-power adapter with a 5025 connector to really test it.

Thanks, all...
  Reply
#8
Just a follow-up...working nicely thru USB-C. I'm not sure whether the problem w the barrel connector is the iron or the power supply...I'll need to get a decent 5025 adapter to try.
  Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Brand new Pinecil v2 won't boot on PD jhutch 0 219 11-07-2022, 04:35 PM
Last Post: jhutch
  Survey on Pinecil Tips, Please fill out River 0 224 11-06-2022, 02:43 AM
Last Post: River
  [available again] When will the Pinecil be available again? dreieck 10 1,998 11-05-2022, 01:48 PM
Last Post: River
  Real/Usable USB-C battery pods for Pinecil? (9-12v mode minimum) biketool 18 5,467 11-05-2022, 01:42 PM
Last Post: River
  Use pinecil (V1) as a high temp thermoemter? Ko1 2 418 11-05-2022, 01:39 PM
Last Post: River
  Brand new Pinecil worked for 30mins - now screen dead and glows red hot! clipclop 3 1,202 11-05-2022, 01:37 PM
Last Post: River
Question Pinecil authenticity checker just reports "Invalid data": What does it mean? dreieck 1 230 11-05-2022, 01:36 PM
Last Post: River
  !! Pinecil is dead after 3 times using it, don't buy this crap... bbeeast 2 1,281 11-05-2022, 01:29 PM
Last Post: River
Big Grin Automate checking whether the Pinecil is still in stock Julius_GU 5 4,686 08-23-2022, 12:54 PM
Last Post: ender__exe
  Asus laptop power supply can also power Pinecil biketool 8 4,402 05-21-2022, 05:56 AM
Last Post: lozza_c

Forum Jump:


Users browsing this thread: 1 Guest(s)