04-23-2025, 10:16 AM
(This post was last modified: 04-23-2025, 10:39 AM by matthewmkr.)
(04-16-2025, 02:45 AM)KC9UDX Wrote: You wouldn't be the first person I heard say had a a bad power supply come with one of these boards. It would be worth trying a different one.
Found my 12V 5A PSU from pine store and same exact issue. Crashes after starting kernel with an ugly video artifact, then white lite blinks.
Could it be that I am using balena etcher to image the SD cards? Does anyone have a link to a known working image and the tool they use for burning the image on SD? I am using Mac or linux. I can spin up a windows machine if I have to. Maybe just use dd on the mac cli?
(04-23-2025, 10:16 AM)matthewmkr Wrote:(04-16-2025, 02:45 AM)KC9UDX Wrote: You wouldn't be the first person I heard say had a a bad power supply come with one of these boards. It would be worth trying a different one.
Found my 12V 5A PSU from pine store and same exact issue. Crashes after starting kernel with an ugly video artifact, then white lite blinks.
Could it be that I am using balena etcher to image the SD cards? Does anyone have a link to a known working image and the tool they use for burning the image on SD? I am using Mac or linux. I can spin up a windows machine if I have to. Maybe just use dd on the mac cli?
Here's my serial output when trying to boot armbian from SD card:
Code:
U-Boot TPL 2025.01-armbian-2025.01-S6d41-Pa8ec-H91a5-V9ecd-Bb703-R448a-dirty (Mar 03 2025 - 16:39:29)
lpddr4_set_rate: change freq to 400MHz 0, 1
Channel 0: LPDDR4, 400MHz
BW=32 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=2048MB
Channel 1: LPDDR4, 400MHz
BW=32 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=2048MB
256B stride
lpddr4_set_rate: change freq to 800MHz 1, 0
Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL 2025.01-armbian-2025.01-S6d41-Pa8ec-H91a5-V9ecd-Bb703-R448a-dirty (Mar 03 2025 - 16:39:29 +0000)
Trying to boot from MMC2
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
## Checking hash(es) for Image u-boot ... sha256+ OK
## Checking hash(es) for Image fdt-1 ... sha256+ OK
## Checking hash(es) for Image atf-2 ... sha256+ OK
## Checking hash(es) for Image atf-3 ... sha256+ OK
## Checking hash(es) for Image atf-4 ... sha256+ OK
load_simple_fit: Skip load 'atf-5': image size is 0!
NOTICE: BL31: v2.12.0(release):armbian
NOTICE: BL31: Built : 23:25:23, Feb 23 2025
INFO: GICv3 with legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: Maximum SPI INTID supported: 287
INFO: plat_rockchip_pmu_init(1624): pd status 3e
INFO: BL31: Initializing runtime services
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
ns16550_serial serial@ff1a0000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
U-Boot 2025.01-armbian-2025.01-S6d41-Pa8ec-H91a5-V9ecd-Bb703-R448a-dirty (Mar 03 2025 - 16:39:29 +0000)
SoC: Rockchip rk3399
Reset cause: POR
Model: Pine64 RockPro64 v2.1
DRAM: 4 GiB (effective 3.9 GiB)
PMIC: RK808
Core: 324 devices, 36 uclasses, devicetree: separate
MMC: mmc@fe310000: 3, mmc@fe320000: 1, mmc@fe330000: 0
Loading Environment from SPIFlash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environment
In: serial,usbkbd
Out: serial,vidconsole
Err: serial,vidconsole
Model: Pine64 RockPro64 v2.1
Net: eth0: ethernet@fe300000
Hit any key to stop autoboot: 0
Scanning for bootflows in all bootdevs
Seq Method State Uclass Part Name Filename
--- ----------- ------ -------- ---- ------------------------ ----------------
Scanning global bootmeth 'efi_mgr':