Here's a thread I created on Reddit. No matter which OS I use, I can't make/receive calls

https://www.reddit.com/r/pinephone/comme..._dead_jim/

Hello, All,

I’m considering a PinePhone/Keyboard purchase and was wondering if folks here might answer a few questions.

I’m fairly versed in Linux and understand that the PP is an indefinite WIP. I don’t expect to use it as a daily driver phone (but certainly hope to someday), but more as a Linux PDA.

1) Will a licensed TextMaker run on PP’s stock Manjaro?

2) Does Manjaro run a full Thunderbird, albeit slowly?

3) Is Newsboat or another terminal RSS reader available?

4) Are the keyboard configs configurable in /usr/share/X11/xkb/ ? For instance, I would like to remap the ?/ key to a Right Shift, then remap ?/ to fn+key or something similar

5) I have read that the kb keys are physically swappable. Is that true?

Many thanks for any answer or advice,
Jake

KB charger chip is off, press the button on the side to turn it on or charge it if it is empty.

pressing button does not change anything.  battery used to work.  charging indicator is On with USB power connected to keyboard.

Hi,

I'm searching for a Pinetab. it seems that it's not becoming available. If here is someone who wants to sell his/her Pinetab. I would like to buy it!

Like many people Linus Torvalds has complained there isn't a serious enough ARM laptop available.
https://www.zdnet.com/article/linux-5-19...-platform/
https://www.youtube.com/watch?v=UAG5Q8Hovkw

Speaking of ARM Linux laptops, when is the Pinebook Pro going to be upgraded to have more RAM, faster CPU, flicker-free display etc?

Hello,

Not sure what I'm doing wrong, but my Pinephone Pro does not start with RE button pressed in order to boot from SD card.  

I just want to install Tow-Boot.


Thank you!

Hello,

I have been attempting to implement PCIe endpoint support on my RockPRO64 board over the past few weeks, but have not been successful and I am starting to doubt that the board can support PCIe EP mode. I'm fairly new to Linux and I am most likely overlooking/missing something as well, but before spending too much more time on this project, I wanted to ensure that it was even possible so I can pursue another route. Has anyone had success with this setup?

At the moment, I am using a custom Armbian build (Debian Sid, no Desktop, kernel v5.19.y) as I was having difficulty setting up Yocto and other off-the-shelf images did not seem to want to boot properly with my board.

I am essentially trying to replicate this tutorial on the RockPRO64 https://docs.nxp.com/bundle/GUID-3FFCCD7...055F0.html  I am able to boot, create an endpoint function, but I am unable to bind the function to the controller as there isn't one!

If the board does truly support PCI Endpoint, I believe it is most likely due to improper configuration of the Device Tree on my end. My various attempts of patching did show some promise.

Apologies for the lack of information, I didn't want to write a lengthy post before determining what I am trying to do is even possible!

Any help would be greatly appreciated!
Thanks, and regards,
Andrew

Hi there,

I hope everyone is doing well. While replacing my screen on my Pinephone pro, I inadvertently tore the ribbon cable to, what looks like the external speaker and possibly the vibration motor. I was wondering if the pinephone and Pinephone pro share the same USB-C side board?

Thanks for all your help, I really appreciate it.

Hi!

I have a similar problem which was described in the topic "PBP booting but stops at flashing power led".

1. history

1.1. PBP worked fine after arrival, Manjaro booted.
1.2. Installed a nvm ssd (with x86 linux boot image from my other laptop, planned to format) I could read the files from it from the booted Manjaro
1.3. Shortly after I started up the ~3rd time I tried to update the OS with the official update tool
1.4. From this point the machine looked dead. I read forums and blogposts and I was able to install Tow-boot to SPI
1.5. Tow-boot works reliably but unable to boot anymore to any OS not from emmc nor SD

2. symptoms

2.1. tow-boot boots every time, reliably
2.2. when booting from emmc it's always start booting but rarely boot up
2.3. newest images (2022 summer) never worked since the update attempt
2.4. void linux console only image sometimes booting up and I can log in and machine looks good but wifi/bt never found
2.5. when switching to SD boot in tow-boot (or disabling/removing emmc) it starts booting exactly every second time
2.6. when it "starts booting" (regardless of success) there's a digital noise image flashing up (will attach it if I can figure out how, but similar than the lower part of the image attached to the PBP booting but stops at flashing power led topic)
2.7. I was able to boot up a Manjaro release from 2021 once (tried ~20 times one was successful)

3. recovery attempts

3.1 ordered second emmc (same size 64) -- no luck
3.2 ordered serial cable, not much help, when it starts booting and the garbage screen flashes, it is in "starting kernel" state
3.3 tried to remove ssd (read about potential power issues) -- no luck
3.4 ordered usb emmc and tried to flash images to that with rpi Images -- no luck that way either
3.5 tried to "hard reset" with the button inside, no effect
3.6 tried various images manjaro/ubuntu/void/etc on SD and on emmc
3.7 tested two SD cards, sandisk 16 (which I learned that not supported) and an other one

What should I try next?

We are currently using UART on pins 8,10 for serial console. Based on the pin diagram, there are 2 more UART's available. One set on pins 15,18 and another set on pins 33,35 which is currently used for SD card slot. We are using Ayufan's Linux kernel release-4.4.167.
We are using EMMC and SD card slot is unused. So we want to disable it and use the UART functionality instead.
How can we configure these pins to be used as UART's. Is it possible to do with dtb overlay ? Is there any User guide or manual which could guide us with this configuration ?
 
Also what is the max baud rate that can be achieved on these UART's ? The one used for console port is 1500000 bauds.