Hi Everybody!

I' received few time ago a Rock64 2G I'll like o use as media server
I'm also trying to connect GPIO to a prototyping board through a ribbon cable 28AWG 40wires (similar to the ones once used for ATA disk) but as soon as I try to connect this cable I have loads of error

androide i rock64 4gb alatt Linux max internet sebesség gigabit.304.62 Mbit / s android korlátozott internet sebessége 80 -104.62 Mbit / s.
miért, mit tegyek. Kösz

Hi ,

Coming chrome 68  google will label  'not secure' HTTP

https://www.computerworld.com/article/32...ummer.html

Hi All,

I had to force the shutdown but after Android Root goes only on Android Recovery mode. I erased, formatted and reflashed the SSD card, the system reinitialized itself but eventually went on recovery again. I read the board has 128 mega dedicate to boot maybe the issue is on that, how can I reset this memory or fixing my current issue?

I flashed another image (Debian minimal), booted it into the board, shutdown it, reflashed the ssd with Android. It worked!

Is there a way to run Magisk on Rock64?

It seems it can't patch Rock64 boot.img correctly and fails.

It is needed for apps to pass Safetynet and Google Certification for some apps to work.

Hi all! 

For a long time I've wanted to make my own NAS, and it looks like the rockpro64 is just what I need. 

My idea is to use a PCIe card with a Marvell 88SE9215 or 
88SE9230 chipset, so I can have up to four drives connected. I don't want to do raid or anything, it's just that I rather have all my storage in the same device. 

Do you know if it should work straight away, or there will be issues with omv or the Linux kernel with the sata card?

Thanks for your time! 

/Xtract

Hello, I got my SOPINE board about 2 months ago and couldn't get it to boot then (same issue, blank screen upon power up). So as of this week I bought a high speed microSD, which before I assumed the reason for not booting was due to a slow SD card. But once again, blank screen  with the new card, and I'm staring to loose faith. Any help would be appreciated.
Thanks

Hello everyone.

I have a problem that I can not solve on my own. I've been trying for some days without success so I had no choice other than asking for help here.

The thing is that I can not set correctly a static IP on my rock64. I mean, I do can, but the device will ALSO maintain the previous DHCP assigned IP forever. My device does have two IP addresses on the same interface eth0 (not even eth0:1). The problem is that the behaviour is unpredictable.  I will explain myself:

For example, I can connect to it using TCP, and it works perfectly, on BOTH IPs.

But, if I use UDP, it will answer with the DHCP assigned IP, thus the source discards the connection.

I have tried everything I could think of. I installed three different ayufan's stable releases as well as non stable ones (jessie minimal 0.5.15, OMV3 0.6.31, OMV3 0.15.5, OMV4, now I have stretch 0.6.31).. And the problem persists.

No matter if I use omv web panel, or /etc/network/interfaces. I can set an IP, but the other one will be there as well forever.

The only thing that I can think of is the way I am installing the OSs, in case there is some problem.

I just use a SD-installed OS to boot, then I use a script that automatically downloads and writes the image to the emmc card. I am not "formatting" that emmc before. rock64_reset_emmc.sh does not work for me, nor does the jumper to boot on sd card. If I have both the sd and emmc, it will boot the sd, so I use it to write the emmc, then I take the sd off to boot from emmc. If I use the jumper, I will boot on SD as well, but the emmc will not be available, even if I take the jumper off, and use the reset script (which says device does not exist).

Thanks for your help. If you need any further information to help me I will provide it as soon as I can.

My battery was almost fully discharged yesterday. Today, after 2hours charge time, I get the Pinebook splash, a flicker, then nothing.

Any thoughts on how to recover form this? I'm in the process of prepping another SD to test the machine, but don't want to have to do a full re-install if I can avoid it. Can I access the update scripts from an SD boot and see if that brings things back to life?

*Interestingly Linux finger magic (Alt+SysRq with r, e, i, s, u, b) will still trigger a reboot from that blank screen, so there's some bit of OS in place to interact with…

Hi,
has anyone of you tried to run Nvidia drivers for "Linux-32bit ARM" for GeForce cards on Rock64 Pro?

Kind regards,
Grzegorz