Improve the life of your Pinebook battery by setting charger's voltage limits
#1
It is a good practice for lithium battery powered devices to briefly think about the charging configuration which can significantly influence the health and usable capacity over time of a battery. Typically, a LiPo battery -- as is also used in the Pinebook -- has a minimum voltage of 3.0 volts (falling below quickly damages the battery) and a maximum voltage of slightly above 4.2 volts (further charging can destroy the battery and even ignite a fire). 

The higher the difference of the battery voltage to these two extremes is, the longer it will keep its initial capacity and the less stress it has to withstand (temperature as another dimension can be critical also, but will be ignored for now). So, quite good voltage limits for charging your Pinebook may be 3.2 to 4.0 volts. The more tentative these limits are set, the less actual battery capacity will be usable, thus less time your Pinebook will be working on battery before it needs to charge.

Luckily, the power management unit AXP803 of the Pinebook allows you to configure, how you wish to set the voltage limits for your actual use case. To this end, you can use the virtual sysfs files in '/sys/class/power_supply/axp20x-battery/' which allow read and write access. I tested this on the current Armbian 5.86, but other distros may offer similar functionality, as they might use the same "axp20x" kernel module for accessing the AXP803 power management unit. 

With read access, you can find out how the limits are currently set. By echoing values into the virtual files, you can persistently write settings to the unit (yes, written values reside on the AXP803 and keep changed even after reboot or shutdown). As the AXP803, for instance, supports only four possible maximum voltages (4.10v, 4.15v, 4.20v, or 4.35v), invalid values as write attempts are caught by the operating system.

Code:
cat /sys/class/power_supply/axp20x-battery/voltage_max_design
cat /sys/class/power_supply/axp20x-battery/voltage_min_design


Charging voltage limits (example with a range of 3.2v ... 4.1v) can be set with:

Code:
echo 4100000 > /sys/class/power_supply/axp20x-battery/voltage_max_design
echo 3200000 > /sys/class/power_supply/axp20x-battery/voltage_min_design


It seems that the maximum voltage is handled by AXP803 (or the kernel driver) with precaution so that my Pinebook battery only charged to up to 4.0 volts with this configuration. The capacity value that is provided in '/sys/class/power_supply/axp20x-battery/capacity' is adjusted automatically to the min and max settings.

I hope, some of you can use these hints to improve the endurance of your Pinebook's battery. Please post a message on your findings relating to practical observations or a different OS.

See for reference on more internals on the power management unit as investigated by xalius:
AXP803 Battery Charger Support
  Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
Information Manjaro ARM for Pinebook erchache2000 87 16,703 10-13-2020, 09:49 AM
Last Post: Corkonian
  Slarm64 on Pinebook [Slackware Arm - 64 bit] KRT 13 3,120 10-03-2020, 04:01 AM
Last Post: mara
  Pinebook Pro (i3 WM): Confirm Shutdown on Power Button etothepii 3 772 08-14-2020, 06:03 AM
Last Post: loblik
  Manjaro sway profile for pinebook e-minguez 3 565 07-21-2020, 03:25 PM
Last Post: jezek
  Reset User or Factory Reset PineBook Linux 11.6" pittman64 1 647 07-07-2020, 11:26 PM
Last Post: tllim
  Pinebook is going the way of Betamax? trigger 9 2,061 06-21-2020, 03:08 PM
Last Post: secristr
  pinebook black screen when booting with "different power mode than last used" penzoiders 12 3,147 04-27-2020, 06:27 AM
Last Post: tophneal
  Kali Linux for the Pinebook Luke 1 965 03-03-2020, 05:01 AM
Last Post: e-minguez
  Anyway to run Teamviewer for ARM/Pinebook? Ekkaia 8 4,949 01-16-2020, 08:51 PM
Last Post: dhosh
  Pinebook Wlan Driver does not work properly matze79 2 675 12-15-2019, 02:50 AM
Last Post: matze79

Forum Jump:


Users browsing this thread: 1 Guest(s)