Hi,
Is the Pinebook Serial Console usable with the Pinebook Pro?
On mine PBP, when I used the Pinebook serial console, it seems to lead to eMMC not responding: when plugged-in from cold boot, I got DDR initialization then it hangs; if I plug the jack after DDR initialization, I got eMMC timeout.
Here is a sample serial output, from a cold boot:
Then it hangs indefinitely. The power LED stays off.
When attaching the jack after u-boot load from eMMC:
With the jack plugged-in but the USB plug not attached to a computer, it boots normally.
What am I doing wrong?
Is the Pinebook Serial Console usable with the Pinebook Pro?
On mine PBP, when I used the Pinebook serial console, it seems to lead to eMMC not responding: when plugged-in from cold boot, I got DDR initialization then it hangs; if I plug the jack after DDR initialization, I got eMMC timeout.
Here is a sample serial output, from a cold boot:
Code:
DDR Version 1.20 20190314
In
channel 0
CS = 0
MR0=0x98
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
CS = 1
MR0=0x18
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 1
CS = 0
MR0=0x98
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
CS = 1
MR0=0x18
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 0 training pass!
channel 1 training pass!
change freq to 400MHz 0,1
channel 0
CS = 0
MR0=0x98
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
CS = 1
MR0=0x18
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 1
CS = 0
MR0=0x98
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
CS = 1
MR0=0x18
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 0 training pass!
channel 1 training pass!
change freq to 800MHz 1,0
Channel 0: LPDDR4,800MHz
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
Channel 1: LPDDR4,800MHz
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
256B stride
ch 0 ddrconfig = 0x101, ddrsize = 0x2020
ch 1 ddrconfig = 0x101, ddrsize = 0x2020
pmugrf_os_reg[2] = 0x3AA1FAA1, stride = 0xD
OUT
DDR Version 1.20 20190314
In
soft reset
SRXWhen attaching the jack after u-boot load from eMMC:
Code:
1: PINEBOOKPRO
2: PINEBOOKPRO-prev-kernel
Enter choice: 1
1: PINEBOOKPRO
Retrieving file: /Image
** Can't read partition table on 0:0 **
** Invalid partition 1 **
Skipping PINEBOOKPRO for failure retrieving kernel
2: PINEBOOKPRO-prev-kernel
Retrieving file: /Image.bak
** Unable to read file /Image.bak **
Skipping PINEBOOKPRO-prev-kernel for failure retrieving kernel
SCRIPT FAILED: continuing...
** fs_devread read error - block
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
** Can't read partition table on 0:0 **
** Invalid partition 1 **
** Can't read partition table on 0:0 **
** Invalid partition 1 **
** Can't read partition table on 0:0 **
** Invalid partition 1 **
** Can't read partition table on 0:0 **
** Invalid partition 1 **
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
mmc_bread: Re-init mmc_read_blocks error
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
mmc_bread: Re-init mmc_read_blocks error
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
mmc_bread: Re-init mmc_read_blocks error
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
mmc_bread: Re-init mmc_read_blocks error
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
mmc_bread: Re-init mmc_read_blocks error
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
mmc_bread: Re-init mmc_read_blocks error
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
mmc_bread: Re-init mmc_read_blocks error
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
mmc_bread: Re-init mmc_read_blocks error
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
mmc_bread: Re-init mmc_read_blocks error
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
mmc_bread: Re-init mmc_read_blocks error
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
mmc fail to send stop cmd
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
mmc fail to send stop cmd
mmc_bread: Re-init mmc_read_blocks error
rkparm_init_param_from_storage param read fail
RKPARM: Invalid parameter part table
mmc fail to send stop cmd
...With the jack plugged-in but the USB plug not attached to a computer, it boots normally.
What am I doing wrong?