Cannot Boot Star64

[jdoolin]

return the switch to the factory state (flash 0,0) and show the log of the entire UART log from the power-on moment when starting any image from the specified theme (download, unpack and burn to the SD card, do not change anything after recording, connect to Star64 and turn on the power).

Please note, there is no bootloader (u-boot) in my images and they work exclusively in startup mode with built-in u-boot (factory state of the device). If you want to test the launch from an SD card, use Fishwaldo images, they have a built-in u-boot and they can work in both switch position options (SD and flashe).

Thanks for the assistance!  Returning the switch to factory state got some much more interesting results, however it is still not booting successfully.  It occurs to me that this may be because I likely did not successfully update the bootloader according to your post on the Armbian boards. But before I attempt that again, I'll post the UART log:

Code:

U-Boot SPL 2021.10 (Jan 19 2023 - 04:09:41 +0800) DDR version: dc2e84f0. Trying to boot from SPI OpenSBI v1.2   ____                    _____ ____ _____   / __ \                  / ____|  _ \_  _| | |  | |_ __  ___ _ __ | (___ | |_) || | | |  | | '_ \ / _ \ '_ \ \___ \|  _ < | | | |__| | |_) |  __/ | | |____) | |_) || |_   \____/| .__/ \___|_| |_|_____/|____/_____|         | |         |_| Platform Name            : StarFive VisionFive V2 Platform Features        : medeleg Platform HART Count      : 5 Platform IPI Device      : aclint-mswi Platform Timer Device    : aclint-mtimer @ 4000000Hz Platform Console Device  : uart8250 Platform HSM Device      : jh7110-hsm Platform PMU Device      : --- Platform Reboot Device    : pm-reset Platform Shutdown Device  : pm-reset Firmware Base            : 0x40000000 Firmware Size            : 288 KB Runtime SBI Version      : 1.0 Domain0 Name              : root Domain0 Boot HART        : 1 Domain0 HARTs            : 0*,1*,2*,3*,4* Domain0 Region00          : 0x0000000002000000-0x000000000200ffff (I) Domain0 Region01          : 0x0000000040000000-0x000000004007ffff () Domain0 Region02          : 0x0000000000000000-0xffffffffffffffff (R,W,X) Domain0 Next Address      : 0x0000000040200000 Domain0 Next Arg1        : 0x0000000042200000 Domain0 Next Mode        : S-mode Domain0 SysReset          : yes Boot HART ID              : 1 Boot HART Domain          : root Boot HART Priv Version    : v1.11 Boot HART Base ISA        : rv64imafdcbx Boot HART ISA Extensions  : none Boot HART PMP Count      : 8 Boot HART PMP Granularity : 4096 Boot HART PMP Address Bits: 34 Boot HART MHPM Count      : 2 Boot HART MIDELEG        : 0x0000000000000222 Boot HART MEDELEG        : 0x000000000000b109 U-Boot 2021.10 (Jan 19 2023 - 04:09:41 +0800), Build: jenkins-github_visionfive2-6 CPU:  rv64imacu Model: StarFive VisionFive V2 DRAM:  8 GiB MMC:  sdio0@16010000: 0, sdio1@16020000: 1 Loading Environment from SPIFlash... SF: Detected gd25lq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment StarFive EEPROM format v2 --------EEPROM INFO-------- Vendor : PINE64 Product full SN: STAR64V1-2310-D008E000-00000021 data version: 0x2 PCB revision: 0xc1 BOM revision: A Ethernet MAC0 address: 6c:cf:39:00:75:99 Ethernet MAC1 address: 6c:cf:39:00:75:9a --------EEPROM INFO-------- In:    serial@10000000 Out:  serial@10000000 Err:  serial@10000000 Model: StarFive VisionFive V2 Net:  eth0: ethernet@16030000, eth1: ethernet@16040000 switch to partitions #0, OK mmc1 is current device found device 1 bootmode flash device 1 ** Invalid partition 3 ** Couldn't find partition mmc 1:3 Can't set block device ** Invalid partition 3 ** Couldn't find partition mmc 1:3 Can't set block device Hit any key to stop autoboot:  0 ** Invalid partition 3 ** Couldn't find partition mmc 1:3 Can't set block device Importing environment from mmc1 ... ## Warning: Input data exceeds 1048576 bytes - truncated ## Info: input data size = 1048578 = 0x100002 ** Invalid partition 2 ** Couldn't find partition mmc 1:2 Can't set block device ## Warning: defaulting to text format ## Error: "boot2" not defined switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 332 bytes read in 6 ms (53.7 KiB/s) 1: Armbian Retrieving file: /boot/uInitrd 24114630 bytes read in 1012 ms (22.7 MiB/s) Retrieving file: /boot/Image 8085097 bytes read in 342 ms (22.5 MiB/s) append: root=UUID=309ddfae-1d04-4ad9-83ea-12a45bfa3520 console=ttyS0,115200n8 console=tty0 earlycon=sbi rw no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 splash plymouth.ignore-serial-consoles Retrieving file: /boot/dtb/starfive/jh7110-pine64-star64.dtb 48314 bytes read in 13 ms (3.5 MiB/s) kernel_comp_addr_r or kernel_comp_size is not provided! SCRIPT FAILED: continuing... Card did not respond to voltage select! : -110 No EFI system partition ethernet@16030000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! phy_startup() failed: -110FAILED: -110ethernet@16040000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! phy_startup() failed: -110FAILED: -110ethernet@16030000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! phy_startup() failed: -110FAILED: -110ethernet@16040000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! phy_startup() failed: -110FAILED: