Iv'e got my pine tab 2 to boot once again and the only thing it says is [    0.000000] clk: failed to reparent gpll to clk_rtc32k_frac: -22 it repeats this line 1 more time and below both lines I get a flashing cursor  does anybody out there know what it means? and what do I need to do to get it run again? please thisis driving me nuts pine64 insists that the community will help please!

Hi
As a new raspberry->pine64 I'm lost in all model options and I find it confusing.
I think a comparison sheet would/table would bring benefit to all buyers to see which on is the most modern which on lack what.

For QUARTZ64 Model-B I found info it can handle 3-pin li-po charging with temp. sensing.

The page for Model-B does not mention it.
So does it mean it's gone in model B?

It's a bit of a hike to get to the end of compiling and installing, but once done, box86/WINE performs admirably on the PP Community phone/physical keyboard.

In xfce (though not in Manjaro Phosh, oddly), LibreOffice has laggy typing, but Word 97, despite its 20-second start-up, has none, and once the program is up, it's as robust as anything on the PP. All its features function and it works with the phone's suspend.

HanDBase, my favorite cross-platform database app, also does its job.

I installed an NVMe drive into my Pinebook Pro. I booted into Majaro from a MicroSD card, blew away the "ROOT_MNJRO" partition from the eMMC drive, and then use the Manjaro flash utility to flash Manjaro Arm for Pinebook to the NVMe drive. On reboot, I completed the setup, rebooted, and then there's no wifi, no audio, connecting my USB ethernet dongle doesn't get recognized, even the power button doesn't work. *UPDATE* The power button does work now.** If I flash this image to the eMMC drive, everything works fine. The same image works fine from the microSD card. For some reason, only when I flash the image to NVMe do I lose all of the functionality of the Pinebook Pro, though I can open a terminal and folders. Hoping someone here can point me in the right direction.

I've been trying to write a Python application for the Pinephone that needs access to the camera.

1. My first iteration was using python-opencv, but that doesn't work out of the box.
The simple first two lines:
```
import cv2
cap = cv2.VideoCapture(0)
```
produce the following error:
```
[ WARN:0@18.736] global ./modules/videoio/src/cap_gstreamer.cpp (2401) handleMessage OpenCV | GStreamer warning: Embedded video playback halted; module v4l2src0 reported: Device '/dev/video0' is not a capture device.
[ WARN:0@18.739] global ./modules/videoio/src/cap_gstreamer.cpp (1356) open OpenCV | GStreamer warning: unable to start pipeline
[ WARN:0@18.740] global ./modules/videoio/src/cap_gstreamer.cpp (862) isPipelinePlaying OpenCV | GStreamer warning: GStreamer: pipeline have not been created
[ WARN:0@18.758] global ./modules/videoio/src/cap_v4l.cpp (902) open VIDEOIO(V4L2:/dev/video0): can't open camera by index

```
There is some discussion about this problem in a manjaro forum: https://forum.manjaro.org/t/access-pinep...encv/94593
but there are no conclusive solutions.

I have two possible work-around to this issue:

2. I could build a python library reusing "megapixels" code (https://gitlab.com/postmarketOS/megapixels). By the way, there is a very interesting description of the pinephone camera interface in the README in that repository.

3. Or I could call an external command from my python executable that gets me the actual camera data, for example `ffmpeg` similarly to this blog post: https://blog.brixit.nl/camera-on-the-pinephone/

In my opinion, solution 3 is ugly and probably under-performant, while 2 seems overkill.
There should be a simple way to read the camera data natively from Python.

If anyone can give me a solution or a hint, I would really appreciate it.

Hi everyone,

my Pinetab2 suddenly stopped working after around 4 weeks of minor usage.
The main symptom is, that the display stays complete black when trying to power on.

As Pine64's support is unfortunately not very helpful and pointed me to the community, i'd really appreciate your help.

I was able to get the following out from UART-console:

Hello everyone,

I have got problem with the USB 3.0 Type A

No information in dmesg or journalctl -f -u systemd-udevd about any devices in this USB port.

$lsusb
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 
Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub 
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub 
Bus 002 Device 002: ID 05e3:0608 Genesys Logic, Inc. Hub 
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 
Bus 008 Device 002: ID 258a:001e HAILUCK CO.,LTD USB KEYBOARD 
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub 
Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

$lsusb -tv
/: Bus 08.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M
ID 1d6b:0001 Linux Foundation 1.1 root hub
|__ Port 1: Dev 2, If 0, Class=Human Interface Device, Driver=usbhid, 1.5M
ID 258a:001e
|__ Port 1: Dev 2, If 1, Class=Human Interface Device, Driver=usbhid, 1.5M
ID 258a:001e
/: Bus 07.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M
ID 1d6b:0002 Linux Foundation 2.0 root hub
/: Bus 06.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M
ID 1d6b:0003 Linux Foundation 3.0 root hub
/: Bus 05.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 480M
ID 1d6b:0002 Linux Foundation 2.0 root hub
/: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M
ID 1d6b:0003 Linux Foundation 3.0 root hub
/: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M
ID 1d6b:0001 Linux Foundation 1.1 root hub
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M
ID 1d6b:0002 Linux Foundation 2.0 root hub
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M
ID 05e3:0608 Genesys Logic, Inc. Hub
|__ Port 1: Dev 6, If 0, Class=Vendor Specific Class, Driver=mt7601u, 480M
ID 148f:7601 Ralink Technology, Corp. MT7601U Wireless Adapter
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 480M
ID 1d6b:0002 Linux Foundation 2.0 root hub


I do not know if this could be hardware issue, OS (Manjaro) or anything else?

Thank you for advice and suggestions.

PS: I've just noticed this post with similar, possibly the same issues https://forum.manjaro.org/t/usb-port-bre...sue/139653

Testing a new Operating System like Apache NuttX RTOS (or Linux) can get painfully tedious on a Single-Board Computer… Swapping, reflashing and rebooting a MicroSD Card, again and again and again! (Like how we tested NuttX on PinePhone)

Thankfully there’s a better way: Booting NuttX (or Linux) over the Local Network, with U-Boot Bootloader and TFTP!

Today we’ll configure TFTP Network Boot on Star64, the new 64-bit RISC-V SBC. (Powered by StarFive JH7110 SoC)


Star64 JH7110 RISC-V SBC: Boot from Network with U-Boot and TFTP

SOLD *** SOLD *** SOLD

Owned for about 3 weeks, in factory condition w/updates. In new condition.  Small scratch on screen is on screen protector (that's what it's for), not screen. I do not have the original box.

I have too many projects and this is just a victim of my needing to focus.

US only, please. Ships from Washington, DC area.

https://www.ebay.com/itm/225668004563


 -Charles

The R4 resistor in my pinecil has failed, when I insert a dc jack I can see a tiny spark in a tiny crack inside the resistor. Is this likely to take down anything else hardware wise, like the mosfet directly in front of it?