80 mm fan not working
#1
L.S.,

I just got the NASCase running. I got the 80 mm fan with it, it is properly plugged in in the right place on the board, but for some reason it is not working. Is this a hardware or a software problem?

My NAS runs OMV.

I already tried to install ATS (https://github.com/tuxd3v/ats), but that didn't work out:

after I run

Code:
luarocks build https://raw.githubusercontent.com/tuxd3v/ats/master/ats-0.2-0.rockspec



I get the following error in the terminal:


Code:
Warning: variable CFLAGS was not passed in build_variables
gcc -c -march=armv8-a+crc -mtune=cortex-a72.cortex-a53 -fPIC -Wall -Werror -O3 -g -I/usr/include/lua5.3  -o debug.o src/debug.c
gcc -c -march=armv8-a+crc -mtune=cortex-a72.cortex-a53 -fPIC -Wall -Werror -O3 -g -I/usr/include/lua5.3  -o ats.o src/ats.c
gcc -shared -Wl,-soname,ats.so.0 -llua5.3  -o ats.so.0.9 debug.o ats.o
Install ATS Tool ..................: ats in /usr/local/sbin
Install ATS Config ................: ats.config in /etc
Install ATS Service File ..........: ats.service in systemd
Remove previous ATS Library .......: ats.so.* from /usr/local/lib/lua/5.3
Install new ATS Library ...........: ats.so.0.9 in /usr/local/lib/lua/5.3
Create soname symLink .............: ats.so in /usr/local/lib/lua/5.3
Starting ATS Service..
● ats.service - ATS - Active Thermal Service
   Loaded: loaded (/lib/systemd/system/ats.service; enabled; vendor preset: enabled)
   Active: activating (auto-restart) (Result: exit-code) since Mon 2019-07-01 01:13:48 UTC; 923ms ago
  Process: 7288 ExecStart=/usr/local/sbin/ats (code=exited, status=1/FAILURE)
 Main PID: 7288 (code=exited, status=1/FAILURE)
      CPU: 14ms

Jul 01 01:13:48 rockpro64 systemd[1]: ats.service: Failed with result 'exit-code'.
Makefile:103: recipe for target 'install' failed
make: *** [install] Error 3

Error: Build error: Failed installing.

Any ideas on what could be happening?

So to be clear the main issue is that the fan isn't working. The secondary issue is that I can't install ATS.

Allt the best,
#2
Its likely ats service - you should take that up in the ats thread.

You can check if hw works: 
Code:
echo 250 > /sys/class/hwmon0/pwm1

change that 250 to a 0 to turn it off
You can find me on IRC, Discord and Twitter


#3
(07-01-2019, 05:08 AM)Luke Wrote: Its likely ats service - you should take that up in the ats thread.

You can check if hw works: 
Code:
echo 250 > /sys/class/hwmon0/pwm1

change that 250 to a 0 to turn it off

I am not sure how to check that. But will bring it to the ATS thread, thanks for the tip.


Possibly Related Threads…
Thread Author Replies Views Last Post
Bug Anyone else's UART RX (serial input) stopped working? pion 1 747 04-07-2022, 08:35 PM
Last Post: foresto
  Cheap 4-port SATA card working with RockPro64 4Gb andyburn 6 8,062 08-10-2020, 08:36 PM
Last Post: zer0sig
  new WIFI/BT module not working with android 8.1 Firesped 0 1,536 05-12-2020, 10:33 PM
Last Post: Firesped
  video not working greenhobby 0 1,143 03-21-2019, 05:56 AM
Last Post: greenhobby

Forum Jump:


Users browsing this thread: 1 Guest(s)