Monitor no output (through HDMI to DVI adaptor)
#1
Hi everybody,

I bought the pine64 2GB version, than I burn the 'Debian Linux Jessie with Mate GUI Image' on the SD card according to the wiki page.
After powering the board, there is nothing on PC monitor, no action, no output. The system boots fine, serial console by EXP connector works, SSH by 'Putty' works.

Please can you advice me what's wrong? My monitor doesn't have HDMI but have DVI. To connect it I use HDMI-DVI adaptor like this: http://www.officeworks.com.au/shop/offic...-cohddviad
I used to use this adaptor with same PC monitor and with Raspberry PI and it was working.

When I use it with pine64 and plug and unplug the monitor cable I get message (on serial console) like this:
[   55.600051] hdmi_clk_disable_prepare()L176
[   62.557231] hdmi_clk_enable_prepare()L161

Also startx doesn't work:
debian@pine64:~$ sudo startx
[sudo] password for debian:


X.Org X Server 1.16.4
Release Date: 2014-12-20
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.16.0-4-arm64 aarch64 Debian
Current Operating System: Linux pine64 3.10.102-0-pine64-longsleep #7 SMP PREEMP T Fri Jun 17 21:30:48 CEST 2016 aarch64
Kernel command line: console=tty0 console=ttyS0,115200n8 no_console_suspend disp .screen0_output_mode=720p60 earlycon=uart,mmio32,0x01c28000 mac_addr=36:c9:e3:f1 :b8:05 root=/dev/mmcblk0p2 ro rootwait
Build Date: 11 February 2015 01:19:23AM
xorg-server 2:1.16.4-1 (http://www.debian.org/support)
Current version of pixman: 0.32.6
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.1.log", Time: Sat Nov 12 14:40:10 2016
(==) Using config file: "/etc/X11/xorg.conf"
(==) Using system config directory "/usr/share/X11/xorg.conf.d"
modprobe: FATAL: Module g2d_23 not found.
modprobe: FATAL: Module mali_drm not found.
modprobe: FATAL: Module sunxi_cedar_mod not found.
SunxiMaliDRI2_Init: drmOpen failed!


Attached Files Thumbnail(s)
   
  Reply


Messages In This Thread
Monitor no output (through HDMI to DVI adaptor) - by gam01hr - 11-12-2016, 08:42 AM

Possibly Related Threads…
Thread Author Replies Views Last Post
Sad HDMI to DVI Color issues? leatherlips 5 16,309 10-09-2017, 05:57 AM
Last Post: Luke
  Would HDMI screen for Raspberry PI work? dhewko 1 3,723 07-23-2017, 06:43 AM
Last Post: MarkHaysHarris777
Exclamation HDMI 1024 x 600 mus1c 4 6,816 01-09-2017, 07:30 AM
Last Post: mus1c
  HDMI-DVI aminhb 11 19,029 01-08-2017, 10:52 AM
Last Post: Luke
  HDMI issues rahlquist 35 49,384 12-24-2016, 02:20 AM
Last Post: sboyce
  HDMI CEC ayufan 15 21,045 09-08-2016, 10:24 AM
Last Post: ayufan
  HDMI to VGA adapter for Android PineA64 tech support setup MarkHaysHarris777 0 2,559 08-06-2016, 12:47 PM
Last Post: MarkHaysHarris777
  hdmi_group CEA or DMT hdmi group specify uEnv.txt MarkHaysHarris777 2 5,367 07-01-2016, 08:23 AM
Last Post: MarkHaysHarris777
  No CEC over HDMI? utdrmac 2 6,066 03-07-2016, 03:05 PM
Last Post: utdrmac
  HDMI 3D, ARC + Ethernet Channels? bigmacattack 4 12,685 01-29-2016, 06:29 PM
Last Post: StefanB

Forum Jump:


Users browsing this thread: 1 Guest(s)