08-09-2020, 06:04 AM
Hi all,
just did a system update on a Rock64 and the new 5.8 Kernel breaks the installation.
After reboot the board has permanently lit the white and red LED and does not boot-up at all.
To narrow down the issue I re-flashed my eMMC-Module as per alarm Wiki and ArchLinuxARM-aarch64-latest.tar.gz includes only linux-aarch64-5.7.1-1 so I run again pacman -Syuu to update and linux-aarch64-5.8.0-1 was installed and after shutdown -r now the board went dead again with permanently lit white and red LED. Pressing the reboot button or pressing and hold the reboot button on the board brings no change, board still ends up with white and red LED permanently lit.
Any ideas on how to fix linux-aarch64-5.8.0-1 so that it works on Rock64 ?
UART output as below
just did a system update on a Rock64 and the new 5.8 Kernel breaks the installation.
After reboot the board has permanently lit the white and red LED and does not boot-up at all.
To narrow down the issue I re-flashed my eMMC-Module as per alarm Wiki and ArchLinuxARM-aarch64-latest.tar.gz includes only linux-aarch64-5.7.1-1 so I run again pacman -Syuu to update and linux-aarch64-5.8.0-1 was installed and after shutdown -r now the board went dead again with permanently lit white and red LED. Pressing the reboot button or pressing and hold the reboot button on the board brings no change, board still ends up with white and red LED permanently lit.
Any ideas on how to fix linux-aarch64-5.8.0-1 so that it works on Rock64 ?
UART output as below
Code:
DDR version 1.06 20170424
In
LPDDR3
786MHz
Bus Width=32 Col=11 Bank=8 Row=15/15 CS=2 Die Bus-Width=32 Size=4096MB
ddrconfig:7
OUT
Boot1 Release Time: 2017-05-18, version: 2.43
ChipType = 0x11, 127
SdmmcInit=2 0
BootCapSize=2000
UserCapSize=119276MB
FwPartOffset=2000 , 2000
SdmmcInit=0 2
StorageInit ok = 23695
Raw SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit ret = 0, SecureMode = 0
LoadTrustBL
No find bl30.bin
No find bl32.bin
Load uboot, ReadLba = 2000
Load OK, addr=0x200000, size=0x8b0ec
RunBL31 0x10000
NOTICE: BL31: v1.3(debug):f947c7e
NOTICE: BL31: Built : 09:28:45, May 31 2017
NOTICE: BL31:Rockchip release version: v1.3
INFO: ARM GICv2 driver initialized
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 1
INFO: plat_rockchip_pmu_init: pd status 0xe
INFO: BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR: Error initializing runtime service opteed_fast
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
U-Boot 2018.03-1 (Apr 02 2018 - 19:14:47 -0600) Arch Linux ARM
Model: Rockchip RK3328 EVB
DRAM: 4 GiB
MMC: rksdmmc@ff500000: 1, rksdmmc@ff520000: 0
Loading Environment from MMC... Card did not respond to voltage select!
*** Warning - No block device, using default environment
Failed (-5)
In: serial@ff130000
Out: serial@ff130000
Err: serial@ff130000
Model: Rockchip RK3328 EVB
Net:
Warning: ethernet@ff540000 (eth0) using random MAC address - 62:72:ba:0a:ad:9a
eth0: ethernet@ff540000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
890 bytes read in 17 ms (50.8 KiB/s)
## Executing script at 00500000
37171712 bytes read in 910 ms (39 MiB/s)
50174 bytes read in 27 ms (1.8 MiB/s)
8342454 bytes read in 211 ms (37.7 MiB/s)
## Flattened Device Tree blob at 01f00000
Booting using the fdt blob at 0x1f00000
Loading Ramdisk to fc727000, end fcf1bbb6 ... OK
reserving fdt memory region: addr=1f00000 size=d000
Loading Device Tree to 00000000fc717000, end 00000000fc726fff ... OK
Starting kernel ...
