Tutorial[ Seagate Disks ]: Install Seagate OpenSeaChest Utilities
#1
Thumbs Up 
Hello All,
I saw that some users have Seagate IronWolfs disks paired with RockPro64..
There are some features that, are nice to configure on Seagate Disks..

Seagate has tools for disks..
Tools that are Present in the OpenSeaChest Utilities:
  • openSeaChest_Basics
  • openSeaChest_Configure
  • openSeaChest_Erase
  • openSeaChest_Firmware
  • openSeaChest_Format
  • openSeaChest_GenericTests
  • openSeaChest_Info
  • openSeaChest_Logs
  • openSeaChest_NVMe
  • openSeaChest_PowerControl
  • openSeaChest_SMART
Here is the Documentation:   Seagate SeaChest Utilities

The Repository is here: OpenSeaChest Utilities



You will need to compile OpenSeaChest Utilities, as root:

1) Jump to /root
Code:
cd /root

2) Use last Stable Release( v19.01.31 - Released 6 days ago, by xahmad )
Code:
git clone --recursive --branch v19.01.31 https://github.com/Seagate/openSeaChest.git

3) Jump into OpenSeaChest gcc compilation method and Compile the project:
    OBS: I tried using parallel compilation and it failed, better to use 1 process only like bellow..
Code:
cd openSeaChest/Make/gcc && make release

4) Wait for compilation to Finish, and check if there are erros at the end.
    If there are no errors, then copy binaries to final destination and remove code stuff used to compile:
Code:
mkdir -pv /opt/openSeaChest/bin && mv openseachest_exes/* /opt/openSeaChest/bin cd / && rm -rf /root/openSeaChest

5) Update your root PATH environment var to know about OpenSeachest Utilities:
Code:
cat <<<'export PATH="${PATH}:/opt/openSeaChest/bin"' >> /root/.bashrc

6) Exit from root and log again has root,
Code:
exit && sudo su -

7) Now try to see if root, knows about OpenSeachest Utilities:
    type "open" and press <TAB>, you will see at least :
Code:
                           openSeaChest_FormatUnit    openSeaChest_PowerControl openSeaChest_Basics        openSeaChest_GenericTests  openSeaChest_SMART openSeaChest_Configure     openSeaChest_Info          openSeaChest_ZBD openSeaChest_Erase         openSeaChest_Logs           openSeaChest_Firmware      openSeaChest_NVMe          

8) Now has a Candy, check information about your Disk, using openSeaChest_Basics:
Code:
# openSeaChest_Basics --deviceInfo --device /dev/sdX ========================================================================================== openSeaChest_Basics - openSeaChest drive utilities - NVMe Enabled Copyright (c) 2014-2018 Seagate Technology LLC and/or its Affiliates, All Rights Reserved openSeaChest_Basics Version: 2.8.0-1_19_0 ARM Build Date: Feb  3 2019 Today: Wed Feb  6 12:56:52 2019 ========================================================================================== /dev/sg0 - ST4000VN008-XXXXXX - XXXXXXXX - ATA Model Number: ST4000VN008-XXXXXX Serial Number: XXXXXXXX Firmware Revision: SC60 World Wide Name: XXXXXXXXXXXXXXXX Drive Capacity (TB/TiB): 4.00/3.64 Native Drive Capacity (TB/TiB): 4.00/3.64 Temperature Data: Current Temperature (C): 16 Highest Temperature (C): 27 Lowest Temperature (C): 13 Power On Time:  4 days 6 hours 59 minutes Power On Hours: 102.98 MaxLBA: 7814037167 Native MaxLBA: 7814037167 Logical Sector Size (B): 512 Physical Sector Size (B): 4096 Sector Alignment: 0 Rotation Rate (RPM): 5980 Form Factor (inch): 3.5 Last DST information: DST has never been run Long Drive Self Test Time:  10 hours 13 minutes Interface speed: Max Speed (Gb/s): 6.0 Negotiated Speed (Gb/s): 6.0 Annualized Workload Rate (TB/yr): 341.03 Total Bytes Read (TB): 4.01 Total Bytes Written (MB): 24.24 Encryption Support: Not Supported Cache Size (MiB): 64.00 Read Look-Ahead: Enabled Write Cache: Enabled Low Current Spinup: Enabled SMART Status: Good ATA Security Information: Supported Firmware Download Support: Full, Segmented, Deferred, DMA Specifications Supported: ACS-3 ACS-2 ATA8-ACS ATA/ATAPI-7 ATA/ATAPI-6 ATA/ATAPI-5 ATA/ATAPI-4 SATA 3.1 SATA 3.0 SATA 2.6 SATA 2.5 SATA II: Extensions SATA 1.0a ATA8-AST Features Supported: Sanitize SATA NCQ SATA Rebuild Assist SATA Software Settings Preservation [Enabled] SATA Device Initiated Power Management HPA Power Management Security SMART [Enabled] DCO 48bit Address PUIS [Enabled] APM [Enabled] GPL Streaming SMART Self-Test SMART Error Logging Write-Read-Verify Sense Data Reporting [Enabled] SCT Write Same SCT Error Recovery Control SCT Feature Control SCT Data Tables Host Logging Seagate In Drive Diagnostics (IDD)

OBS: Read Carefully the Documentation about OpenSeachest Utilities, to not damage your data, or your disk..
          Start by openSeaChest_Basics tool, which seems less prone, to problems.. in the time you are aquiring the needed skills..

Hope you Enjoy.. [Image: thumbsup.png]
Regards


Messages In This Thread
Tutorial[ Seagate Disks ]: Install Seagate OpenSeaChest Utilities - by tuxd3v - 02-06-2019, 07:05 AM

Possibly Related Threads…
Thread Author Replies Views Last Post
  SkiffOS server with Docker ,NAS, Home assistant, Jellyfin, Snikket XMPP (tutorial) GreyLinux 12 27,510 04-04-2022, 05:26 AM
Last Post: GreyLinux
  SimpNas server with docker - home assistant, radicale , jellyfin & esphome (tutorial) GreyLinux 0 9,120 01-17-2021, 11:33 AM
Last Post: GreyLinux
  Tutorial:How to Configure ATS Fan control tuxd3v 26 84,018 11-06-2020, 08:56 PM
Last Post: g_t_j
  Serial Connection Tutorial: FTDI 232RL hmuller 0 8,434 10-23-2020, 11:56 AM
Last Post: hmuller
Video How to Install Google PlayStore NightCrawler504 2 9,401 04-08-2020, 02:20 PM
Last Post: pino88
Wink Tutorial[ Seagate Disks ]: Optimize Life Span/Power Managment tuxd3v 14 43,256 06-19-2019, 04:40 AM
Last Post: Neo2018
Video Video and Guide to install Android to emmc no emmc to usb adapter NightCrawler504 0 5,280 04-21-2019, 07:19 PM
Last Post: NightCrawler504
  Tutorial[ Multimedia ] : Play DVD movies tuxd3v 0 5,312 02-26-2019, 07:21 PM
Last Post: tuxd3v
  Tutorial[ OpenCL ]: OpenCL 1.2 FULL_PROFILE Working tuxd3v 0 6,033 11-06-2018, 01:03 PM
Last Post: tuxd3v
  HOW TO - install linux on emmc without etcher or USB adapter dukla2000 4 16,135 07-31-2018, 12:40 PM
Last Post: dukla2000

Forum Jump:


Users browsing this thread: 1 Guest(s)