08-25-2016, 01:07 PM
(This post was last modified: 08-25-2016, 01:50 PM by MarkHaysHarris777.)
(08-23-2016, 09:26 AM)MarkHaysHarris777 Wrote:(08-23-2016, 08:56 AM)CrazyBird Wrote: Well, checking the filesystem on another linux system didn't lead to a solution.
googled for VFE_ERR and found out that it comes from a "sunxi Camera Interface driver" - I'm pretty sure I would'nt need that because I have no cam installed - so is there a chance to remove this driver?
On the other linux system did you mount the SD card and run fsck on both partitions... but especially the mmcblk0p2 ?
Just rechecked both partitions - both are allright according to fsck.
Still, the issue remains an I'm not able to use my PINE with ubuntu.
Another question: i can't find a boot.log on the system...
Thanks again for any help
Stefan
Here my dmesg - output. Hope that helps:
Code:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.65-7-pine64-longsleep (longsleep@mose2) (gcc version 5.3.1 20160413 (Ubuntu/Linaro 5.3.1-14ubuntu2) ) #28 SMP PREEMPT Sat Apr 23 20:13:25 CEST 2016
[ 0.000000] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000] Machine: sun50iw1p1
[ 0.000000] cma: CMA: reserved 64 MiB at bc000000
[ 0.000000] On node 0 totalpages: 520192
[ 0.000000] DMA zone: 7112 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 520192 pages, LIFO batch:31
[ 0.000000] script_init enter!
[ 0.000000] script buffer is NULL!
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv0.2 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] PERCPU: Embedded 12 pages/cpu @ffffffc07af92000 s19712 r8192 d21248 u49152
[ 0.000000] pcpu-alloc: s19712 r8192 d21248 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 513080
[ 0.000000] Kernel command line: console=tty0 console=ttyS0,115200n8 no_console_suspend earlycon=uart,mmio32,0x01c28000 mac_addr=8e:21:0d:2e:ad:67 root=/dev/mmcblk0p2 ro rootwait
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Memory: 2032MB = 2032MB total
[ 0.000000] Memory: 1969976k/1969976k available, 110792k reserved
[ 0.000000] Virtual kernel memory layout:
vmalloc : 0xffffff8000000000 - 0xffffffbbffff0000 (245759 MB)
vmemmap : 0xffffffbc00e38000 - 0xffffffbc02a00000 ( 27 MB)
modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
memory : 0xffffffc000000000 - 0xffffffc07f000000 ( 2032 MB)
.init : 0xffffffc000957000 - 0xffffffc0009d0d00 ( 488 kB)
.text : 0xffffffc000080000 - 0xffffffc0009569b4 ( 9051 kB)
.data : 0xffffffc0009d1000 - 0xffffffc000b27168 ( 1369 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 8388608 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 7.295473] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 7.295504] pid_max: default: 32768 minimum: 301
[ 7.295608] Security Framework initialized
[ 7.295643] AppArmor: AppArmor initialized
[ 7.295687] Mount-cache hash table entries: 256
[ 7.306106] Initializing cgroup subsys memory
[ 7.306166] Initializing cgroup subsys devices
[ 7.306183] Initializing cgroup subsys freezer
[ 7.306199] Initializing cgroup subsys blkio
[ 7.306214] Initializing cgroup subsys perf_event
[ 7.306235] Initializing cgroup subsys hugetlb
[ 7.306285] ftrace: allocating 25847 entries in 101 pages
[ 7.336424] CPU0: update cpu_power 1968128
[ 7.336458] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 7.337381] virtual base = 0xffffff800000a000.
[ 7.337401] gicd_base = 0xffffff800000c000.
[ 7.337414] gicc_base = 0xffffff800000e000.
[ 7.337990] CPU1: Booted secondary processor
[ 7.338013] CPU1: update cpu_power 1968128
[ 7.340615] CPU2: Booted secondary processor
[ 7.340627] CPU2: update cpu_power 1968128
[ 7.344734] CPU3: Booted secondary processor
[ 7.344745] CPU3: update cpu_power 1968128
[ 7.344823] Brought up 4 CPUs
[ 7.344897] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 7.345428] devtmpfs: initialized
[ 7.350214] atomic64 test passed
[ 7.350236] pinctrl core: initialized pinctrl subsystem
[ 7.353212] NET: Registered protocol family 16
[ 7.353522] script_sysfs_init success
[ 7.354363] dump_class_init,806, success
[ 7.355000] vdso: 2 pages (1 code, 1 data) at base ffffffc0009d9000
[ 7.355033] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 7.356342] software IO TLB [mem 0xb8800000-0xb8c00000] (4MB) mapped at [ffffffc077800000-ffffffc077bfffff]
[ 7.357270] DMA: preallocated 256 KiB pool for atomic allocations
[ 7.357451] Serial: AMBA PL011 UART driver
[ 7.357826] axp81x_board_init: axp regl_devs num = 23
[ 7.358040] pll_audio-set_default_rate=24576000 success!
[ 7.358071] pll_video0-set_default_rate=297000000 success!
[ 7.358154] pll_video1-set_default_rate=297000000 success!
[ 7.358223] pll_de-set_default_rate=297000000 success!
[ 7.358955] de-set_default_source=pll_de success!
[ 7.358972] de-set_default_rate=297000000 success!
[ 7.359025] tcon0-set_default_source=pll_mipi success!
[ 7.359068] tcon1-set_default_source=pll_video0 success!
[ 7.359299] hdmi-set_default_source=pll_video0 success!
[ 7.361834] sun50i-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver
[ 7.362083] [sun50iw1p1_pinctrl_probe][838]
[ 7.363832] sun50i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 7.365122] sunxi hwspinlock vbase:0xffffff800005c000
[ 7.375044] sunxi_chipid_probe,150: soc bin:0
[ 7.392190] bio: create slab <bio-0> at 0
[ 7.392611] pwm module init!
[ 7.394913] SCSI subsystem initialized
[ 7.395401] usbcore: registered new interface driver usbfs
[ 7.395518] usbcore: registered new interface driver hub
[ 7.395655] usbcore: registered new device driver usb
[ 7.396945] Linux video capture interface: v2.00
[ 7.397881] [ARISC] :sunxi-arisc driver v1.10
[ 7.409676] [ARISC] :sunxi-arisc driver v1.10 startup succeeded
[ 7.410075] Advanced Linux Sound Architecture Driver Initialized.
[ 7.410647] NetLabel: Initializing
[ 7.410661] NetLabel: domain hash size = 128
[ 7.410673] NetLabel: protocols = UNLABELED CIPSOv4
[ 7.410719] NetLabel: unlabeled traffic allowed by default
[ 7.410967] [pm]aw_pm_init!
[ 7.411050] rtc physical base = 0x0000000001f00000 .
[ 7.411094] np name = /soc@01c00000/rtc@01f00000.
[ 7.411110] base = ffffff8000070100, len = 4.
[ 7.411123] pmu name: pmu0 .
[ 7.411168] pmu0_enable = 0x1.
[ 7.411181] pmux_id = 0x6.
[ 7.411193] pmux_twi_id = 0x1.
[ 7.411205] pmux_twi_addr = 0x34.
[ 7.411216] pmu name: pmu1 .
[ 7.411273] Warning: can not find np for pmu1.
[ 7.411508] add_sys_pwr_dm: get ldo name for id: vcc-lpddr failed
[ 7.411674] after inited: sys_mask config = 0x4a55.
[ 7.411707] Warning: can not find np for dynamic_standby_para.
[ 7.411839] [pm]valid
[ 7.411849] [pm]valid
[ 7.411859] Notice: sun9i&sun8iw5&sun50i not need support normal standby, change to super standby.
[ 7.412057] Switching to clocksource arch_sys_counter
[ 7.422607] AppArmor: AppArmor Filesystem Enabled
[ 7.434978] NET: Registered protocol family 2
[ 7.435625] TCP established hash table entries: 16384 (order: 6, 262144 bytes)
[ 7.435884] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 7.436168] TCP: Hash tables configured (established 16384 bind 16384)
[ 7.436253] TCP: reno registered
[ 7.436270] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 7.436332] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 7.436577] NET: Registered protocol family 1
[ 7.436847] RPC: Registered named UNIX socket transport module.
[ 7.436865] RPC: Registered udp transport module.
[ 7.436879] RPC: Registered tcp transport module.
[ 7.436892] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 7.437056] Unpacking initramfs...
[ 7.480683] Freeing initrd memory: 1048K (ffffffc075dad000 - ffffffc075eb3000)
[ 7.481438] kvm [1]: Using HYP init bounce page @b9bdd000
[ 7.481895] kvm [1]: interrupt-controller@1c84000 IRQ25
[ 7.482245] kvm [1]: timer IRQ27
[ 7.482264] kvm [1]: Hyp mode initialized successfully
[ 7.483622] lock super standby defaultly!
[ 7.483648] lookup_scene_lock_name: new scene lock super_standby
[ 7.483664] scene_lock_init name=super_standby
[ 7.483679] scene_lock: super_standby, type 5, count 1
[ 7.484349] audit: initializing netlink socket (disabled)
[ 7.484399] type=2000 audit(0.180:1): initialized
[ 7.485354] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 7.485815] VFS: Disk quotas dquot_6.5.2
[ 7.485931] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 7.486352] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 7.486753] NFS: Registering the id_resolver key type
[ 7.486803] Key type id_resolver registered
[ 7.486817] Key type id_legacy registered
[ 7.486837] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 7.486986] NTFS driver 2.1.30 [Flags: R/W].
[ 7.487246] fuse init (API version 7.22)
[ 7.487641] msgmni has been set to 3977
[ 7.488457] io scheduler noop registered
[ 7.488473] io scheduler deadline registered
[ 7.488510] io scheduler cfq registered (default)
[ 7.489316] [DISP]disp_module_init
[ 7.489869] [DISP] boot_disp:0x40a
[ 7.490442] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[ 7.490602] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[ 7.490761] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[ 7.491894] [DISP] fb_base:0x47400000
[ 7.499459] [DISP] Fb_map_kernel_logo,line:885:this is not a bmp picture.
[ 7.529339] Console: switching to colour frame buffer device 240x67
[ 7.558291] [DISP]disp_module_init finish
[ 7.558816] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
[ 7.558971] sw_console_setup()1173 - console setup baud 115200 parity n bits 8, flow n
[ 8.519619] console [ttyS0] enabled
[ 8.524073] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI
[ 8.531099] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI
[ 8.538211] uart3: ttyS3 at MMIO 0x1c28c00 (irq = 35) is a SUNXI
[ 8.545286] uart4: ttyS4 at MMIO 0x1c29000 (irq = 36) is a SUNXI
[ 8.552484] misc dump reg init
[ 8.556234] [drm] Initialized drm 1.1.0 20060810
[ 8.564893] loop: module loaded
[ 8.568662] sunxi-bt bt.27: Missing bt_power.
[ 8.573541] sunxi-bt bt.27: bt_power_name ((null))
[ 8.578883] sunxi-bt bt.27: io_regulator_name (vcc-wifi-io)
[ 8.585133] sunxi-bt bt.27: bt_rst gpio=356 mul-sel=1 pull=-1 drv_level=-1 data=0
[ 8.593903] sunxi-bt bt.27: clk not config
[ 8.598600] sunxi-bt bt.27: block state already is 1
[ 8.604452] sunxi-wlan wlan.26: wlan_busnum (1)
[ 8.609502] sunxi-wlan wlan.26: Missing wlan_power.
[ 8.614946] sunxi-wlan wlan.26: wlan_power_name ((null))
[ 8.620867] sunxi-wlan wlan.26: io_regulator_name (vcc-wifi-io)
[ 8.627494] sunxi-wlan wlan.26: wlan_regon gpio=354 mul-sel=1 pull=-1 drv_level=-1 data=0
[ 8.637033] sunxi-wlan wlan.26: wlan_hostwake gpio=355 mul-sel=6 pull=-1 drv_level=-1 data=0
[ 8.646851] sunxi-wlan wlan.26: clk not config
[ 8.652458] tun: Universal TUN/TAP device driver, 1.6
[ 8.658090] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 8.665689] WARNING: Get ephy clock is failed
[ 8.671170] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.678612] get ehci0-controller drv_vbus_gpio is fail
[ 8.684351] get ehci0-controller, regulator_io is no nocare
[ 8.690611] [sunxi-ehci0]: probe, pdev->name: 1c1a000.ehci0-controller, sunxi_ehci: 0xffffffc000bd16a8, 0x:ffffff80000ae000, irq_no:68
[ 8.704141] sunxi-ehci 1c1a000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.714252] sunxi-ehci 1c1a000.ehci0-controller: new USB bus registered, assigned bus number 1
[ 8.724152] sunxi-ehci 1c1a000.ehci0-controller: irq 104, io mem 0xffffffc0004bf654
[ 8.750362] sunxi-ehci 1c1a000.ehci0-controller: USB 0.0 started, EHCI 1.00
[ 8.758125] ehci_irq: highspeed device connect
[ 8.763675] hub 1-0:1.0: USB hub found
[ 8.773878] hub 1-0:1.0: 1 port detected
[ 8.784289] scene_lock_init name=ehci_standby
[ 8.795104] get ehci1-controller drv_vbus_gpio is fail
[ 8.806664] get ehci1-controller, regulator_io is no nocare
[ 8.818705] [sunxi-ehci1]: probe, pdev->name: 1c1b000.ehci1-controller, sunxi_ehci: 0xffffffc000bd18f8, 0x:ffffff80000b6000, irq_no:6a
[ 8.838166] sunxi-ehci 1c1b000.ehci1-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.854388] sunxi-ehci 1c1b000.ehci1-controller: new USB bus registered, assigned bus number 2
[ 8.870392] sunxi-ehci 1c1b000.ehci1-controller: irq 106, io mem 0xffffffc0004bf654
[ 8.897961] sunxi-ehci 1c1b000.ehci1-controller: USB 0.0 started, EHCI 1.00
[ 8.911836] ehci_irq: highspeed device connect
[ 8.923511] hub 2-0:1.0: USB hub found
[ 8.933887] hub 2-0:1.0: 1 port detected
[ 8.944564] scene_lock_init name=ehci_standby
[ 8.955893] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.969199] get ohci0-controller drv_vbus_gpio is fail
[ 8.981252] get ohci0-controller, regulator_io is no nocare
[ 8.993749] [sunxi-ohci0]: probe, pdev->name: 1c1a000.ohci0-controller, sunxi_ohci: 0xffffffc000bd1208
[ 9.010436] sunxi-ohci 1c1a000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 9.026454] sunxi-ohci 1c1a000.ohci0-controller: new USB bus registered, assigned bus number 3
[ 9.042353] sunxi-ohci 1c1a000.ohci0-controller: irq 105, io mem 0x6a626e6b61ff726b
[ 9.094766] usb 1-1: new high-speed USB device number 2 using sunxi-ehci
[ 9.118903] hub 3-0:1.0: USB hub found
[ 9.129327] hub 3-0:1.0: 1 port detected
[ 9.140008] scene_lock_init name=ohci_standby
[ 9.151076] get ohci1-controller drv_vbus_gpio is fail
[ 9.162893] get ohci1-controller, regulator_io is no nocare
[ 9.175236] [sunxi-ohci1]: probe, pdev->name: 1c1b000.ohci1-controller, sunxi_ohci: 0xffffffc000bd1458
[ 9.191730] sunxi-ohci 1c1b000.ohci1-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 9.207551] sunxi-ohci 1c1b000.ohci1-controller: new USB bus registered, assigned bus number 4
[ 9.223285] sunxi-ohci 1c1b000.ohci1-controller: irq 107, io mem 0x6a626e6b61ff726b
[ 9.295977] hub 4-0:1.0: USB hub found
[ 9.306529] hub 4-0:1.0: 1 port detected
[ 9.317324] scene_lock_init name=ohci_standby
[ 9.329017] usbcore: registered new interface driver usb-storage
[ 9.342043] ehci_irq: highspeed device disconnect
[ 9.353632] ohci_irq: fullspeed or lowspeed device connect
[ 9.366190] usbcore: registered new interface driver ums-alauda
[ 9.379348] usbcore: registered new interface driver ums-cypress
[ 9.392490] usbcore: registered new interface driver ums-datafab
[ 9.405549] usbcore: registered new interface driver ums_eneub6250
[ 9.418728] usbcore: registered new interface driver ums-freecom
[ 9.431690] usbcore: registered new interface driver ums-isd200
[ 9.444501] usbcore: registered new interface driver ums-jumpshot
[ 9.457499] usbcore: registered new interface driver ums-karma
[ 9.470191] usbcore: registered new interface driver ums-onetouch
[ 9.483125] usbcore: registered new interface driver ums-realtek
[ 9.495870] usbcore: registered new interface driver ums-sddr09
[ 9.508426] usbcore: registered new interface driver ums-sddr55
[ 9.520881] usbcore: registered new interface driver ums-usbat
[ 9.533306] usbcore: registered new interface driver usbserial
[ 9.545538] usbcore: registered new interface driver usbserial_generic
[ 9.558454] usbserial: USB Serial support registered for generic
[ 9.571164] mousedev: PS/2 mouse device common for all mice
[ 9.583555] input: sunxi-keyboard as /devices/virtual/input/input0
[ 9.596747] sunxi-rtc 1f00000.rtc: rtc core: registered rtc-sunxi as rtc0
[ 9.609842] sunxi-rtc 1f00000.rtc: RTC enabled
[ 9.656251] input: axp81x-supplyer as /devices/platform/axp81x_board/axp81x-supplyer.47/input/input1
[ 9.678715] sunxi budget cooling probe start !
[ 9.689305] CPU freq cooling register Success
[ 9.699753] CPU hotplug cooling register Success
[ 9.710517] CPU budget cooling register Success
[ 9.721502] sunxi gpu cooling probe start !
[ 9.731663] CPU gpu cooling register Success
[ 9.744768] cpuidle: using governor ladder
[ 9.754129] cpuidle: using governor menu
[ 9.764074] sunxi-mmc 1c0f000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.20 2015-7-13 16:28) Compiled in Apr 23 2016 at 17:56:40
[ 9.782284] sunxi-mmc 1c0f000.sdmmc: regulator prop vmmc,str none
[ 9.793783] sunxi-mmc 1c0f000.sdmmc: regulator prop vqmmc,str none
[ 9.805310] sunxi-mmc 1c0f000.sdmmc: regulator prop vdmmc,str vcc-sdc
[ 9.817123] sunxi-mmc 1c0f000.sdmmc: No vmmc regulator found
[ 9.828006] sunxi-mmc 1c0f000.sdmmc: No vqmmc regulator found
[ 9.839353] sunxi-mmc 1c0f000.sdmmc: Got CD GPIO #166.
[ 9.849812] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 9.865542] sunxi-mmc 1c0f000.sdmmc: no vqmmc,Check if there is regulator
[ 9.891860] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 9.921338] sunxi-mmc 1c0f000.sdmmc: base:0xffffff80000ca000 irq:92
[ 9.921343] usb 4-1: new full-speed USB device number 2 using sunxi-ohci
[ 9.945607] sunxi-mmc 1c10000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.20 2015-7-13 16:28) Compiled in Apr 23 2016 at 17:56:40
[ 9.963479] sunxi-mmc 1c10000.sdmmc: Can't get vmmc regulator string
[ 9.975339] sunxi-mmc 1c10000.sdmmc: Can't get vqmmc regulator string
[ 9.987254] sunxi-mmc 1c10000.sdmmc: Can't get vdmmc regulator string
[ 9.999102] get() with no identifier
[ 10.007736] get() with no identifier
[ 10.016290] get() with no identifier
[ 10.020524] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 52, RTO !!
[ 10.021336] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 52, RTO !!
[ 10.021352] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 10.023732] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 10.025858] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !!
[ 10.026667] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !!
[ 10.027476] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !!
[ 10.028285] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !!
[ 10.028913] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B
[ 10.028953] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B
[ 10.031324] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B
[ 10.170862] sunxi-mmc 1c10000.sdmmc: No vmmc regulator found
[ 10.181320] sunxi-mmc 1c10000.sdmmc: No vqmmc regulator found
[ 10.182219] mmc0: SD Status: Invalid Allocation Unit size.
[ 10.183857] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 10.185552] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B
[ 10.185591] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B
[ 10.185685] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 4 timing SD-HS(SDR25) dt B
[ 10.185704] mmc0: new high speed SDXC card at address 0001
[ 10.274044] mmcblk0: mmc0:0001 00000 59.6 GiB
[ 10.274143] sunxi-mmc 1c10000.sdmmc: No vdmmc regulator found
[ 10.295069] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 10.295935] mmcblk0: p1 p2
[ 10.319055] sunxi-mmc 1c10000.sdmmc: no vqmmc,Check if there is regulator
[ 10.344448] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 10.373968] sunxi-mmc 1c10000.sdmmc: base:0xffffff80000d2000 irq:93
[ 10.374765] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 10.375572] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 10.375587] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 10.377959] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 10.379774] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 8, RTO !!
[ 10.380580] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 10.381384] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 10.382189] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 10.382993] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 10.383800] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !!
[ 10.384607] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !!
[ 10.385412] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !!
[ 10.386216] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !!
[ 10.386232] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 10.387064] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 1, RTO !!
[ 10.387079] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[ 10.595336] input: Logitech USB Receiver as /devices/soc.0/1c1b000.ohci1-controller/usb4/4-1/4-1:1.0/input/input2
[ 10.611763] hid-generic 0003:046D:C52B.0001: input: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-sunxi-ohci-1/input0
[ 10.634936] input: Logitech USB Receiver as /devices/soc.0/1c1b000.ohci1-controller/usb4/4-1/4-1:1.1/input/input3
[ 10.651604] hid-generic 0003:046D:C52B.0002: input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-sunxi-ohci-1/input1
[ 10.676087] hid-generic 0003:046D:C52B.0003: device has no listeners, quitting
[ 10.689402] usbcore: registered new interface driver usbhid
[ 10.700792] usbhid: USB HID core driver
[ 10.711521] usbcore: registered new interface driver snd-usb-audio
[ 10.725611] sndhdmi sound.7: sndhdmi <-> 1c22800.daudio mapping ok
[ 10.738826] TCP: cubic registered
[ 10.747739] NET: Registered protocol family 10
[ 10.758330] sit: IPv6 over IPv4 tunneling driver
[ 10.769071] NET: Registered protocol family 17
[ 10.779014] Key type dns_resolver registered
[ 10.788754] Registering SWP/SWPB emulation handler
[ 10.799778] [DISP] boot_disp:0x40a
[ 10.809262] [HDMI] power vcc-hdmi-33
[ 10.818585] [HDMI] cec support = 0
[ 11.079817] [DISP] disp_device_attached,line:94:attched ok, mgr0<-->device1, type=4
[ 11.094194] sunxi-rtc 1f00000.rtc: setting system clock to 2010-01-01 00:00:08 UTC (1262304008)
[ 11.109796] input: sunxi-ths as /devices/virtual/input/input4
[ 11.121636] thermal thermal_zone0: failed to read out thermal zone 0
[ 11.134342] ALSA device list:
[ 11.142898] #0: sndhdmi
[ 11.151342] Freeing unused kernel memory: 484K (ffffffc000957000 - ffffffc0009d0000)
[ 11.574443] [ehci0-controller]: sunxi_usb_disable_ehci
[ 11.585629] [sunxi-ehci0]: remove, pdev->name: 1c1a000.ehci0-controller, sunxi_ehci: 0xffffffc000bd16a8
[ 11.601615] scene_lock_destroy name=ehci_standby
[ 11.612317] sunxi-ehci 1c1a000.ehci0-controller: remove, state 1
[ 11.624654] usb usb1: USB disconnect, device number 1
[ 11.635997] usb 1-1: USB disconnect, device number 2
[ 11.649319] sunxi-ehci 1c1a000.ehci0-controller: USB bus 1 deregistered
[ 11.662440] ohci_irq: fullspeed or lowspeed device connect
[ 11.674368] [ohci0-controller]: sunxi_usb_disable_ohci
[ 11.685799] [sunxi-ohci0]: remove, pdev->name: 1c1a000.ohci0-controller, sunxi_ohci: 0xffffffc000bd1208
[ 11.701962] scene_lock_destroy name=ohci_standby
[ 11.712856] sunxi-ohci 1c1a000.ohci0-controller: remove, state 84
[ 11.889381] usb usb3: USB disconnect, device number 1
[ 12.007933] sunxi-ohci 1c1a000.ohci0-controller: USB bus 3 deregistered
[ 12.021135] [ehci0-controller]: sunxi_usb_enable_ehci
[ 12.032580] [sunxi-ehci0]: probe, pdev->name: 1c1a000.ehci0-controller, sunxi_ehci: 0xffffffc000bd16a8, 0x:ffffff80000ae000, irq_no:68
[ 12.051958] sunxi-ehci 1c1a000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 12.067992] sunxi-ehci 1c1a000.ehci0-controller: new USB bus registered, assigned bus number 1
[ 12.083940] sunxi-ehci 1c1a000.ehci0-controller: irq 104, io mem 0xffffffc0006b0664
[ 12.115636] sunxi-ehci 1c1a000.ehci0-controller: USB 0.0 started, EHCI 1.00
[ 12.129215] ehci_irq: highspeed device connect
[ 12.140595] hub 1-0:1.0: USB hub found
[ 12.150733] hub 1-0:1.0: 1 port detected
[ 12.161300] scene_lock_init name=ehci_standby
[ 12.172209] [ohci0-controller]: sunxi_usb_enable_ohci
[ 12.183752] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[ 12.183847] [sunxi-ohci0]: probe, pdev->name: 1c1a000.ohci0-controller, sunxi_ohci: 0xffffffc000bd1208
[ 12.183902] sunxi-ohci 1c1a000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 12.183923] sunxi-ohci 1c1a000.ohci0-controller: new USB bus registered, assigned bus number 3
[ 12.183960] sunxi-ohci 1c1a000.ohci0-controller: irq 105, io mem 0xffffffc0006b0664
[ 12.238229] hub 3-0:1.0: USB hub found
[ 12.238242] hub 3-0:1.0: 1 port detected
[ 12.238375] scene_lock_init name=ohci_standby
[ 12.295565] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[ 12.382328] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 12.469925] usb 1-1: new high-speed USB device number 2 using sunxi-ehci
[ 12.733066] systemd[1]: System time before build time, advancing clock.
[ 12.853050] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[ 12.880122] systemd[1]: Detected architecture arm64.
[ 12.913608] systemd[1]: Set hostname to <Corellia>.
[ 13.513359] systemd[1]: [/etc/systemd/system/eth0-mackeeper.service:6] Unknown lvalue 'After' in section 'Service'
[ 13.531564] systemd[1]: [/etc/systemd/system/eth0-mackeeper.service:7] Unknown lvalue 'After' in section 'Service'
[ 13.580706] systemd[1]: Listening on udev Kernel Socket.
[ 13.611435] systemd[1]: PNFS blkmaping enablement. is not active.
[ 13.640888] systemd[1]: Dependency failed for pNFS block layout mapping daemon.
[ 13.670424] systemd[1]: nfs-blkmap.service: Job nfs-blkmap.service/start failed with result 'dependency'.
[ 13.687901] systemd[1]: Listening on udev Control Socket.
[ 13.719939] systemd[1]: Listening on Syslog Socket.
[ 13.749296] systemd[1]: Listening on Journal Socket.
[ 13.778782] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 13.808267] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 13.837706] systemd[1]: Reached target Encrypted Volumes.
[ 13.867302] systemd[1]: Listening on Journal Socket (/dev/log).
[ 13.897109] systemd[1]: Created slice System Slice.
[ 13.928143] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 13.967630] systemd[1]: Mounting POSIX Message Queue File System...
[ 13.997159] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 14.035078] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 14.066244] systemd[1]: Starting Journal Service...
[ 14.095285] systemd[1]: Starting Nameserver information manager...
[ 14.154608] systemd[1]: Started Braille Device Support.
[ 14.171534] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 14.194823] systemd[1]: Mounting Huge Pages File System...
[ 14.238423] systemd[1]: Starting Load Kernel Modules...
[ 14.272657] systemd[1]: Starting Set console keymap...
[ 14.300425] systemd[1]: Reached target Swap.
[ 14.330320] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 14.348578] ppdev: user-space parallel port driver
[ 14.366056] systemd[1]: Reached target User and Group Name Lookups.
[ 14.399008] systemd[1]: Created slice User and Session Slice.
[ 14.428253] systemd[1]: Reached target Slices.
[ 14.459324] systemd[1]: Mounting RPC Pipe File System...
[ 14.487453] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 14.518436] systemd[1]: Mounting NFSD configuration filesystem...
[ 14.548039] systemd[1]: Mounting Debug File System...
[ 14.579717] systemd[1]: Mounted NFSD configuration filesystem.
[ 14.599063] systemd[1]: Mounted RPC Pipe File System.
[ 14.635012] systemd[1]: Mounted Huge Pages File System.
[ 14.664450] systemd[1]: Mounted Debug File System.
[ 14.693998] systemd[1]: Mounted POSIX Message Queue File System.
[ 14.723892] systemd[1]: Started Journal Service.
[ 14.851708] cfg80211: Calling CRDA to update world regulatory domain
[ 14.998337] RTL871X: module init start
[ 15.008770] RTL871X: rtl8723bs v4.3.16_13854.20150410_BTCOEX20150119-5844
[ 15.022214] RTL871X: build time: Apr 23 2016 17:32:18
[ 15.033694] RTL871X: rtl8723bs BT-Coex version = BTCOEX20150119-5844
[ 15.046687] sunxi-wlan wlan.26: bus_index: 1
[ 15.057594] sunxi-wlan wlan.26: check wlan io_regulator voltage: 1800000
[ 15.134752] systemd-journald[903]: Received request to flush runtime journal from PID 1
[ 15.166135] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 15.184330] sunxi-mmc 1c10000.sdmmc: no vqmmc,Check if there is regulator
[ 15.199469] RTL871X: module init ret=0
[ 15.225130] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 15.255443] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 15.275121] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 15.287861] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 15.307838] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 15.329080] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 8, RTO !!
[ 15.342291] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B
[ 15.372317] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B
[ 15.390859] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B
[ 15.410373] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 4 timing SD-HS(SDR25) dt B
[ 15.430408] mmc1: new high speed SDIO card at address 0001
[ 15.476829] RTL871X: rtw_ndev_init(wlan0)
[ 15.478008] RTL871X: rtw_ndev_init(wlan1)
[ 16.410028] sunxi cedar version 0.1
[ 16.410230] [cedar]: install start!!!
[ 16.410337] ycy the get irq is 90
[ 16.411039] ycy clk_bass_vir 0x18 is ffffff8002892018, the value:3006207
[ 16.411050] ycy clk_bass_vir 0x13c is ffffff800289213c, the value:0
[ 16.411056] ycy clk_bass_vir 0x64 is ffffff8002892064, the value:601810
[ 16.411060] ycy clk_bass_vir 0x2c4 is ffffff80028922c4, the value:601c10
[ 16.411065] ycy clk_bass_vir 0x100 is ffffff8002892100, the value:0
[ 16.411068] [cedar]: install end!!!
[ 16.534693] Mali: Set gpu frequency to 408 MHz
[ 16.534754] Mali: Init Mali gpu clocks successfully
[ 16.545619] gpu cooling callback register Success
[ 16.550499] Mali: Mali device driver loaded
[ 16.552425] [VFE]cci probe end cci_sel = 0!
[ 16.552737] [VFE]cci_init end
[ 16.703602] cfg80211: World regulatory domain updated:
[ 16.703606] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 16.703614] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 16.703617] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 16.703619] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 16.703622] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 16.703624] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 16.703627] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[ 16.703629] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 16.703632] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 16.975938] [VFE]Welcome to Video Front End driver
[ 16.976306] [VFE]csi probe end csi_sel = 0!
[ 16.978074] [VFE]csi_init end
[ 16.978671] [VFE]isp probe start isp_sel = 0!
[ 16.986027] [ISP] isp platform_id = 3!
[ 16.986049] [VFE]isp probe end isp_sel = 0!
[ 16.988137] [VFE]sunxi_isp_platform_register end
[ 16.988732] [VFE]mipi probe start mipi_sel = 0!
[ 16.988763] [VFE]mipi probe end mipi_sel = 0!
[ 16.989293] [VFE]mipi_init end
[ 16.989311] [VFE]flash_init end
[ 16.990433] [VFE]pdev->id = 0
[ 16.990447] [VFE]dev->vip_sel = 0
[ 16.990475] [VFE_WARN]fetch csi0_dev0_twi_id from device_tree failed
[ 16.990513] [VFE_WARN]fetch csi0_dev0_afvdd from device_tree failed
[ 16.990521] [VFE_WARN]fetch csi0_dev0_afvdd_vol from device_tree failed
[ 16.990531] [VFE_WARN]fetch csi0_dev0_power_en from device_tree failed
[ 16.990579] [VFE_WARN]fetch csi0_dev0_flash_en from device_tree failed
[ 16.990587] [VFE_WARN]fetch csi0_dev0_flash_mode from device_tree failed
[ 16.990599] [VFE_WARN]fetch csi0_dev0_af_pwdn from device_tree failed
[ 16.990621] [VFE_WARN]fetch csi0_dev1_twi_id from device_tree failed
[ 16.990649] [VFE_WARN]fetch csi0_dev1_afvdd from device_tree failed
[ 16.990655] [VFE_WARN]fetch csi0_dev1_afvdd_vol from device_tree failed
[ 16.990662] [VFE_WARN]fetch csi0_dev1_power_en from device_tree failed
[ 16.990684] [VFE_WARN]fetch csi0_dev1_flash_en from device_tree failed
[ 16.990692] [VFE_WARN]fetch csi0_dev1_flash_mode from device_tree failed
[ 16.990703] [VFE_WARN]fetch csi0_dev1_af_pwdn from device_tree failed
[ 16.990723] [VFE]fetch rear sensor list info start!
[ 16.990727] [VFE]Fetch sensor list form"/system/etc/hawkview/sensor_list_cfg.ini"
[ 17.031128] [vfe_warn]open file failed!
[ 17.046010] gpu cooling callback set freq limit 0
[ 17.141323] [VFE]fetch rear sensor list info end!
[ 17.141377] [VFE]fetch front sensor list info start!
[ 17.141381] [VFE]Fetch sensor list form"/system/etc/hawkview/sensor_list_cfg.ini"
[ 17.177984] [vfe_warn]open file failed!
[ 17.212472] sunxi-bt bt.27: set block: 0
[ 17.212623] sunxi-bt bt.27: check bluetooth io_regulator voltage: 1800000
[ 17.216017] [VFE]fetch front sensor list info end!
[ 17.216223] [VFE_WARN]os_gpio_request failed, gpio=129, ret=0xfffffff0, -16
[ 17.216595] [VFE]vfe_init end
[ 17.222914] [VFE]probe_work_handle start!
[ 17.223066] [VFE]vfe_runtime_resume
[ 17.235112] [VFE]..........................vfe clk open!.......................
[ 17.235128] [VFE_WARN]vfe dphy clock is null
[ 17.235152] [VFE]v4l2 subdev register input_num = 0
[ 17.235293] [VFE]vfe sensor detect start! input_num = 0
[ 17.235303] [VFE_WARN]NOT found this item: hm5065, you can add this sensor in the sensor_list_t!
[ 17.235309] [VFE]Sub device register "hm5065" i2c_addr = 0x3e start!
[ 17.235315] [VFE_ERR]Error registering v4l2 subdevice No such device!
[ 17.250383] [VFE_ERR]vfe sensor register check error at input_num = 0
[ 17.263395] [VFE]v4l2 subdev register input_num = 1
[ 17.263449] axp81x_aldo1: Failed to create debugfs directory
[ 17.263462] axp81x_dldo3: Failed to create debugfs directory
[ 17.263474] axp81x_eldo3: Failed to create debugfs directory
[ 17.263484] axp81x_aldo1: Failed to create debugfs directory
[ 17.263489] [VFE]vfe sensor detect start! input_num = 1
[ 17.263499] [VFE_WARN]NOT found this item: gc2145, you can add this sensor in the sensor_list_t!
[ 17.263504] [VFE]Sub device register "gc2145" i2c_addr = 0x78 start!
[ 17.263511] [VFE_ERR]Error registering v4l2 subdevice No such device!
[ 17.276450] [VFE_ERR]vfe sensor register check error at input_num = 1
[ 17.289671] [VFE]V4L2 device registered as (null)
[ 17.289708] [VFE]vfe_runtime_suspend
[ 17.289713] [VFE]..........................vfe clk close!.......................
[ 17.295883] [VFE]probe_work_handle end!
[ 103.590737] type=1400 audit(1472108337.853:2): apparmor="STATUS" operation="profile_load" name="/usr/lib/snapd/snap-confine" pid=2552 comm="apparmor_parser"
[ 103.631568] type=1400 audit(1472108337.893:3): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=2549 comm="apparmor_parser"
[ 103.631987] type=1400 audit(1472108337.893:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=2549 comm="apparmor_parser"
[ 103.632400] type=1400 audit(1472108337.893:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=2549 comm="apparmor_parser"
[ 103.632789] type=1400 audit(1472108337.893:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=2549 comm="apparmor_parser"
[ 103.645443] type=1400 audit(1472108337.903:7): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm-guest-session" pid=2548 comm="apparmor_parser"
[ 103.645952] type=1400 audit(1472108337.903:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm-guest-session//chromium" pid=2548 comm="apparmor_parser"
[ 103.669872] type=1400 audit(1472108337.933:9): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cups-browsed" pid=2554 comm="apparmor_parser"
[ 103.680977] type=1400 audit(1472108337.943:10): apparmor="STATUS" operation="profile_load" name="/usr/sbin/ippusbxd" pid=2557 comm="apparmor_parser"
[ 103.699594] type=1400 audit(1472108337.963:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=2556 comm="apparmor_parser"
[ 104.327027] libphy: 1c30000.eth: probed
[ 104.327179] sunxi-gmac 1c30000.eth eth0: eth0: PHY ID 001cc915 at 0 IRQ poll (1c30000.eth-0:00)
[ 110.230457] libphy: 1c30000.eth-0:00 - Link is Up - 1000/Full