12-16-2018, 08:21 PM
I've been trying to get opensuse Tumbleweed to boot on my 2Gb rock64.
The image I used was downloaded from:
https://download.opensuse.org/repositori...ip/images/
After dd'ing the image to the emmc, I installed the Arch u-boot using this install guide:
https://archlinuxarm.org/platforms/armv8...hip/rock64
Using these kernel arguments in grub2/grub.cfg . I'm able to see where the boot process stops:
$linux ($root)//Image-4.19.5-1-default ${extra_cmdline} loglevel=7 earlycon=uart8250,mmio32,0xff130000 console=ttyS0,1500000n8 splash=silent plymouth.enable=0 root=UUID=d90c3637-cea7-412c-8aa7-e3a5a47dad39 rw
So after unpacking the initramfs, it stops after saying it can't open the rtc.
[ 29.068003] Freeing initrd memory: 30036K
[ 29.071144] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[ 29.072396] kvm [1]: 8-bit VMID
[ 29.074816] kvm [1]: vgic interrupt IRQ1
[ 29.075557] kvm [1]: Hyp mode initialized successfully
[ 29.081276] Initialise system trusted keyrings
[ 29.082177] workingset: timestamp_bits=44 max_order=19 bucket_order=0
[ 29.083355] zbud: loaded
[ 29.086027] pstore: using deflate compression
[ 29.101879] Key type asymmetric registered
[ 29.102309] Asymmetric key parser 'x509' registered
[ 29.102901] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 29.103982] io scheduler noop registered
[ 29.104388] io sched[ 29.104995] io scheduler cfq registered (default)
[ 29.105[ 29.105954] io scheduler bfq registered
[ 29.115404] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 29.136242] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 29.163163] Serial: AMBA driver
[ 29.164563] msm_serial: driver initialized
[ 29.167928] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 29.170729] libphy: Fixed MDIO Bus: probed
[ 29.172295] mousedev: PS/2 mouse device common for all mice
[ 29.181473] ledtrig-cpu: registered to indicate activity on CPUs
[ 29.182859] EFI Variables Facility v0.08 2004-May-17
[ 29.183463] efivars: get_next_variable: status=8000000000000007
[ 29.184227] hidraw: raw HID events driver © Jiri Kosina
[ 29.189808] NET: Registered protocol family 10
[ 29.227610] Segment Routing with IPv6
[ 29.230255] registered taskstats version 1
[ 29.230691] Loading compiled-in X.509 certificates
[ 29.231347] zswap: loaded using pool lzo/zbud
[ 29.261624] cryptd: max_cpu_qlen set to 1000
[ 29.290314] Key type big_key registered
[ 29.318665] Key type encrypted registered
[ 29.319101] AppArmor: AppArmor sha1 policy hashing enabled
[ 29.319728] ima:p found, activating TPM-bypass!
[ 29.320325] ima: Allocated h[ 29.320986] evm: Initialising EVM extended attributes:
[ 229.321845] evm: security.apparmor
[ 29.322192] evm: security.61] evm: HMAC attrs: 0x1
[ 29.370627] hctosys: unable to open rtc device (rtc0)
checking for rtc in the device tree blob show no entry:
fdtdump rk3328-rock64.dtb |grep rtc
Checking the kernel config does show 2 entries:
cat config-4.19.5-1-default |grep rtc
CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
CONFIG_RTC_SYSTOHC_DEVICE="rtc0"
When I boot ayuran's bionic image I see that the rtc is provided by:
dmesg
rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0
I posted this same info on opensuse's arm mailing list, but I haven't gotten any response yet.
https://lists.opensuse.org/opensuse-arm/...00016.html
I don't know how to fix this, but maybe this information will help you.
Thanks.
Mark
The image I used was downloaded from:
https://download.opensuse.org/repositori...ip/images/
After dd'ing the image to the emmc, I installed the Arch u-boot using this install guide:
https://archlinuxarm.org/platforms/armv8...hip/rock64
Using these kernel arguments in grub2/grub.cfg . I'm able to see where the boot process stops:
$linux ($root)//Image-4.19.5-1-default ${extra_cmdline} loglevel=7 earlycon=uart8250,mmio32,0xff130000 console=ttyS0,1500000n8 splash=silent plymouth.enable=0 root=UUID=d90c3637-cea7-412c-8aa7-e3a5a47dad39 rw
So after unpacking the initramfs, it stops after saying it can't open the rtc.
[ 29.068003] Freeing initrd memory: 30036K
[ 29.071144] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[ 29.072396] kvm [1]: 8-bit VMID
[ 29.074816] kvm [1]: vgic interrupt IRQ1
[ 29.075557] kvm [1]: Hyp mode initialized successfully
[ 29.081276] Initialise system trusted keyrings
[ 29.082177] workingset: timestamp_bits=44 max_order=19 bucket_order=0
[ 29.083355] zbud: loaded
[ 29.086027] pstore: using deflate compression
[ 29.101879] Key type asymmetric registered
[ 29.102309] Asymmetric key parser 'x509' registered
[ 29.102901] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 29.103982] io scheduler noop registered
[ 29.104388] io sched[ 29.104995] io scheduler cfq registered (default)
[ 29.105[ 29.105954] io scheduler bfq registered
[ 29.115404] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 29.136242] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 29.163163] Serial: AMBA driver
[ 29.164563] msm_serial: driver initialized
[ 29.167928] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 29.170729] libphy: Fixed MDIO Bus: probed
[ 29.172295] mousedev: PS/2 mouse device common for all mice
[ 29.181473] ledtrig-cpu: registered to indicate activity on CPUs
[ 29.182859] EFI Variables Facility v0.08 2004-May-17
[ 29.183463] efivars: get_next_variable: status=8000000000000007
[ 29.184227] hidraw: raw HID events driver © Jiri Kosina
[ 29.189808] NET: Registered protocol family 10
[ 29.227610] Segment Routing with IPv6
[ 29.230255] registered taskstats version 1
[ 29.230691] Loading compiled-in X.509 certificates
[ 29.231347] zswap: loaded using pool lzo/zbud
[ 29.261624] cryptd: max_cpu_qlen set to 1000
[ 29.290314] Key type big_key registered
[ 29.318665] Key type encrypted registered
[ 29.319101] AppArmor: AppArmor sha1 policy hashing enabled
[ 29.319728] ima:p found, activating TPM-bypass!
[ 29.320325] ima: Allocated h[ 29.320986] evm: Initialising EVM extended attributes:
[ 229.321845] evm: security.apparmor
[ 29.322192] evm: security.61] evm: HMAC attrs: 0x1
[ 29.370627] hctosys: unable to open rtc device (rtc0)
checking for rtc in the device tree blob show no entry:
fdtdump rk3328-rock64.dtb |grep rtc
Checking the kernel config does show 2 entries:
cat config-4.19.5-1-default |grep rtc
CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
CONFIG_RTC_SYSTOHC_DEVICE="rtc0"
When I boot ayuran's bionic image I see that the rtc is provided by:
dmesg
rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0
I posted this same info on opensuse's arm mailing list, but I haven't gotten any response yet.
https://lists.opensuse.org/opensuse-arm/...00016.html
I don't know how to fix this, but maybe this information will help you.
Thanks.
Mark
