Found this fully working RASPBIAN Image that boots to desktop

[speedro86]

You need to edit a file you can find on the sdcard by putting it in the card reader on your laptop. There is a configure.txt where you can edit. My wifi worked from the beginning.

[Bluphire]

can you copy and paste your config file here for all to see and compare to? thanks.

[Shai]

You need to edit a file you can find on the sdcard by putting it in the card reader on your laptop. There is a configure.txt where you can edit. My wifi worked from the beginning.

well can you say what did you config in this file? i have the build in bluetooth/wifi expand card but it says network interfaces unavailable.

[tommypine]

You need to edit a file you can find on the sdcard by putting it in the card reader on your laptop. There is a configure.txt where you can edit. My wifi worked from the beginning.

well can you say what did you config in this file? i have the build in bluetooth/wifi expand card but it says network interfaces unavailable.

Whooooooo, it seems to be a great secret, he don't want to tell us......hehehehe  

[dkryder]

i think he is referring to config.txt in bpi-boot folder
read some details here,
https://www.raspberrypi.org/documentatio...fig-txt.md

[Bluphire]

Why cant he just share what his config file says?!

[cr2016]

Thanks for the link dkryder, a lot more than 'some details' there 

[Bluphire]

Speedro86 - Are you using WiFi with the WiFi/BT module or are you using a WiFi dongle?

[tommypine]

This image is not worth the time i spend trying on it.
Wifi NOT working, Sound NOT working, BT NOT working.
Grapics extremly sloooow, try to drag a window around.
Forget it.

[speedro86]

yes the config.txt in the bpi-boot folder. If you cant get things working, I dont know what to say, other than editing this file for hdmi, everything else worked first time(for me). Here is the file exactly as I have it:

# For more options and information see
# http://www.raspberrypi.org/documentation...fig-txt.md
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on