06-13-2019, 04:02 AM
Hello tuxd3v, I managed to install OpenSeaChest Utilities!
With USB 3.0 external enclosure 3.5 and Ubuntu.
I hope it works now.
Can you please advise me, which settings are most appropriate for my needs?
I mainly use for multimedia entertainment (stream DLNA, movie, music).
1. I want that the hard drive consumes so little power, because most of the time it will be in standby, and only when streaming needs power.
2. Which Spindown time is appropriate for my needs? (Do I need this?)
3. Which power management makes sense for my needs? (127, 128, 192?)
4. Which settings are important to activate?
Many Thanks!
With USB 3.0 external enclosure 3.5 and Ubuntu.
I hope it works now.
Code:
root@ubuntu:~# lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
sdd 8:48 0 7.3T 0 disk
└─sdd1 8:49 0 7.3T 0 part /media/ubuntu/Daten3
sdb 8:16 0 465.8G 0 disk
├─sdb4 8:20 0 254.2G 0 part /media/ubuntu/9852F7D552F7B65A
├─sdb2 8:18 0 100M 0 part
├─sdb5 8:21 0 211G 0 part /media/ubuntu/Daten
├─sdb3 8:19 0 16M 0 part
└─sdb1 8:17 0 499M 0 part
sr0 11:0 1 1024M 0 rom
loop0 7:0 0 1.4G 1 loop /rofs
sdc 8:32 1 28.7G 0 disk
└─sdc4 8:36 1 28.7G 0 part /cdrom
sda 8:0 0 489.1G 0 disk
└─sda1 8:1 0 489G 0 part /media/ubuntu/DatenspeicherCode:
root@ubuntu:~/openSeaChest/Make/gcc/openseachest_exes# ./openSeaChest_Basics --deviceInfo --device /dev/sdd1
==========================================================================================
openSeaChest_Basics - openSeaChest drive utilities - NVMe Enabled
Copyright (c) 2014-2018 Seagate Technology LLC and/or its Affiliates, All Rights Reserved
openSeaChest_Basics Version: 2.8.0-1_19_0 X86_64
Build Date: Jun 13 2019
Today: Thu Jun 13 09:02:29 2019
==========================================================================================
/dev/sg4 - 3.0 - BCDEF - ATA
Vendor ID: USB
Model Number: 3.0
Serial Number: 0123456789ABCDEF
Firmware Revision: 0508
World Wide Name: 5000C500B4ADB587
Drive Capacity (TB/TiB): 8.00/7.28
Temperature Data:
Current Temperature (C): 32
Highest Temperature (C): 50
Lowest Temperature (C): 23
Power On Time: 2 hours
Power On Hours: 2.00
MaxLBA: 15628053167
Native MaxLBA: Not Reported
Logical Sector Size (B): 512
Physical Sector Size (B): 4096
Sector Alignment: 0
Rotation Rate (RPM): 7200
Form Factor (inch): 3.5
Last DST information:
DST has never been run
Long Drive Self Test Time: 13 hours 24 minutes
Interface speed:
Max Speed (Gb/s): 6.0
Negotiated Speed (Gb/s): 6.0
Annualized Workload Rate (TB/yr): 283.06
Total Bytes Read (MB): 593.95
Total Bytes Written (GB): 64.03
Encryption Support: Not Supported
Cache Size (MiB): 256.00
Read Look-Ahead: Enabled
Write Cache: Enabled
Low Current Spinup: Disabled
SMART Status: Unknown or Not Supported
ATA Security Information: Supported
Firmware Download Support: Full, Segmented, Deferred
Specifications Supported:
ACS-3
ACS-2
ATA8-ACS
ATA/ATAPI-7
ATA/ATAPI-6
ATA/ATAPI-5
ATA/ATAPI-4
SATA 3.1
SATA 3.0
SATA 2.6
SATA 2.5
SATA II: Extensions
SATA 1.0a
ATA8-AST
SPC-4
UAS
SPC-4
SBC-3
Features Supported:
Sanitize
SATA NCQ
SATA Rebuild Assist
SATA Software Settings Preservation [Enabled]
SATA Device Initiated Power Management
Power Management
Security
SMART [Enabled]
48bit Address
PUIS
GPL
Streaming
SMART Self-Test
SMART Error Logging
Write-Read-Verify
AMAC
EPC [Enabled]
Sense Data Reporting
SCT Write Same
SCT Error Recovery Control
SCT Feature Control
SCT Data Tables
Host Logging
Seagate In Drive Diagnostics (IDD)
Seagate RemanufactureCan you please advise me, which settings are most appropriate for my needs?
I mainly use for multimedia entertainment (stream DLNA, movie, music).
1. I want that the hard drive consumes so little power, because most of the time it will be in standby, and only when streaming needs power.
2. Which Spindown time is appropriate for my needs? (Do I need this?)
3. Which power management makes sense for my needs? (127, 128, 192?)
4. Which settings are important to activate?
Many Thanks!
