hi,
I don't have a wifi BTmodule so I am trying to bring up a wifi dongle on my Pine64 2G device. Running with Debian.
I pulled the dongle off my raspberry pi since I know it works.
My ethernet will come up but I can't seem to get the wifi dongle to work. No network connection at all with the dongle.
I have.
/etc/network/interfaces
# The wireless interface
auto wlan0
iface wlan0 inet dhcp
wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf
iface default inet dhcp
# Disable Secondary Wireless Lan (8723bs Has Two Interfaces)
iface wlan1 inet manual
..and...
/etc/wpa_supplicant/wpa_supplicant.conf
network={
ssid="Test Net Wifi"
psk="network-password"
proto=RSN
key_mgmt=WPA-PSK
pairwise=CCMP
auth_alg=OPEN
}
Any ideas on what I am missing? Do I need to update any drivers?
thanks
Mike
Can you check if you actually got a driver loaded for the dongle? Try "iwconfing" , does it show any interfaces? Try "lsmod" , does it show any modules for the dongle? lsusb , dmesg output could also give a clue....
Thank you for responding.
Here is what I am seeing with the commands you requested.
The two commands you suggested for ismod and isusb weren't recognized. The following are the iwconfig and dmesg outputs.
Thank you
Mike
Code: eth0 no wireless connections
sith0 no wireless connections
lo no wireless connections
Code: [ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.101-0-pine64-longsleep (longsleep@mose2) (gcc version 5.3.1 20160413 (Ubuntu/Linaro 5.3.1-14ubuntu2) ) #39 SMP PREEMPT Sat May 7 12:39:25 CEST 2016
[ 0.000000] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000] Machine: sun50iw1p1
[ 0.000000] cma: CMA: reserved 64 MiB at bc000000
[ 0.000000] On node 0 totalpages: 520192
[ 0.000000] DMA zone: 7112 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 520192 pages, LIFO batch:31
[ 0.000000] script_init enter!
[ 0.000000] script buffer is NULL!
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv0.2 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] PERCPU: Embedded 12 pages/cpu @ffffffc07af92000 s18816 r8192 d22144 u49152
[ 0.000000] pcpu-alloc: s18816 r8192 d22144 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 513080
[ 0.000000] Kernel command line: console=tty0 console=ttyS0,115200n8 no_console_suspend disp.screen0_output_mode=720p60 earlycon=uart,mmio32,0x01c28000 mac_addr=36:c9:e3:f1:b8:05 root=/dev/mmcblk0p2 ro rootwait
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Memory: 2032MB = 2032MB total
[ 0.000000] Memory: 1969892k/1969892k available, 110876k reserved
[ 0.000000] Virtual kernel memory layout:
vmalloc : 0xffffff8000000000 - 0xffffffbbffff0000 (245759 MB)
vmemmap : 0xffffffbc00e38000 - 0xffffffbc02a00000 ( 27 MB)
modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
memory : 0xffffffc000000000 - 0xffffffc07f000000 ( 2032 MB)
.init : 0xffffffc00096c000 - 0xffffffc0009e5980 ( 487 kB)
.text : 0xffffffc000080000 - 0xffffffc00096ba24 ( 9135 kB)
.data : 0xffffffc0009e6000 - 0xffffffc000b3c8b8 ( 1371 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 8388608 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 7.237935] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 7.237966] pid_max: default: 32768 minimum: 301
[ 7.238072] Security Framework initialized
[ 7.238106] AppArmor: AppArmor initialized
[ 7.238150] Mount-cache hash table entries: 256
[ 7.248647] Initializing cgroup subsys memory
[ 7.248707] Initializing cgroup subsys devices
[ 7.248724] Initializing cgroup subsys freezer
[ 7.248740] Initializing cgroup subsys blkio
[ 7.248755] Initializing cgroup subsys perf_event
[ 7.248775] Initializing cgroup subsys hugetlb
[ 7.248844] ftrace: allocating 26058 entries in 102 pages
[ 7.279282] CPU0: update cpu_power 1968128
[ 7.279316] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 7.280251] virtual base = 0xffffff800000a000.
[ 7.280270] gicd_base = 0xffffff800000c000.
[ 7.280283] gicc_base = 0xffffff800000e000.
[ 7.280869] CPU1: Booted secondary processor
[ 7.280892] CPU1: update cpu_power 1968128
[ 7.283494] CPU2: Booted secondary processor
[ 7.283506] CPU2: update cpu_power 1968128
[ 7.287615] CPU3: Booted secondary processor
[ 7.287626] CPU3: update cpu_power 1968128
[ 7.287705] Brought up 4 CPUs
[ 7.287781] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 7.288299] devtmpfs: initialized
[ 7.293194] atomic64 test passed
[ 7.293215] pinctrl core: initialized pinctrl subsystem
[ 7.296203] NET: Registered protocol family 16
[ 7.296521] script_sysfs_init success
[ 7.297375] dump_class_init,806, success
[ 7.298037] vdso: 2 pages (1 code, 1 data) at base ffffffc0009ed000
[ 7.298070] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 7.299378] software IO TLB [mem 0xb8800000-0xb8c00000] (4MB) mapped at [ffffffc077800000-ffffffc077bfffff]
[ 7.300297] DMA: preallocated 256 KiB pool for atomic allocations
[ 7.300479] Serial: AMBA PL011 UART driver
[ 7.300859] axp81x_board_init: axp regl_devs num = 23
[ 7.301079] pll_audio-set_default_rate=24576000 success!
[ 7.301111] pll_video0-set_default_rate=297000000 success!
[ 7.301189] pll_video1-set_default_rate=297000000 success!
[ 7.301257] pll_de-set_default_rate=297000000 success!
[ 7.301984] de-set_default_source=pll_de success!
[ 7.302000] de-set_default_rate=297000000 success!
[ 7.302053] tcon0-set_default_source=pll_mipi success!
[ 7.302095] tcon1-set_default_source=pll_video0 success!
[ 7.302330] hdmi-set_default_source=pll_video0 success!
[ 7.304836] sun50i-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver
[ 7.305090] [sun50iw1p1_pinctrl_probe][838]
[ 7.306815] sun50i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 7.308110] sunxi hwspinlock vbase:0xffffff800005c000
[ 7.318038] sunxi_chipid_probe,150: soc bin:0
[ 7.335362] bio: create slab <bio-0> at 0
[ 7.335788] pwm module init!
[ 7.338116] SCSI subsystem initialized
[ 7.338586] usbcore: registered new interface driver usbfs
[ 7.338720] usbcore: registered new interface driver hub
[ 7.338857] usbcore: registered new device driver usb
[ 7.340158] Linux video capture interface: v2.00
[ 7.341090] [ARISC] :sunxi-arisc driver v1.10
[ 7.352671] [ARISC] :sunxi-arisc driver v1.10 startup succeeded
[ 7.353080] Advanced Linux Sound Architecture Driver Initialized.
[ 7.353667] NetLabel: Initializing
[ 7.353681] NetLabel: domain hash size = 128
[ 7.353694] NetLabel: protocols = UNLABELED CIPSOv4
[ 7.353752] NetLabel: unlabeled traffic allowed by default
[ 7.354005] [pm]aw_pm_init!
[ 7.354089] rtc physical base = 0x0000000001f00000 .
[ 7.354134] np name = /soc@01c00000/rtc@01f00000.
[ 7.354149] base = ffffff8000070100, len = 4.
[ 7.354163] pmu name: pmu0 .
[ 7.354206] pmu0_enable = 0x1.
[ 7.354219] pmux_id = 0x6.
[ 7.354231] pmux_twi_id = 0x1.
[ 7.354242] pmux_twi_addr = 0x34.
[ 7.354253] pmu name: pmu1 .
[ 7.354311] Warning: can not find np for pmu1.
[ 7.354548] add_sys_pwr_dm: get ldo name for id: vcc-lpddr failed
[ 7.354713] after inited: sys_mask config = 0x4a55.
[ 7.354745] Warning: can not find np for dynamic_standby_para.
[ 7.354873] [pm]valid
[ 7.354883] [pm]valid
[ 7.354892] Notice: sun9i&sun8iw5&sun50i not need support normal standby, change to super standby.
[ 7.355102] Switching to clocksource arch_sys_counter
[ 7.365746] AppArmor: AppArmor Filesystem Enabled
[ 7.378196] NET: Registered protocol family 2
[ 7.378880] TCP established hash table entries: 16384 (order: 6, 262144 bytes)
[ 7.379139] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 7.379443] TCP: Hash tables configured (established 16384 bind 16384)
[ 7.379530] TCP: reno registered
[ 7.379548] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 7.379609] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 7.379849] NET: Registered protocol family 1
[ 7.380140] RPC: Registered named UNIX socket transport module.
[ 7.380157] RPC: Registered udp transport module.
[ 7.380170] RPC: Registered tcp transport module.
[ 7.380184] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 7.380355] Unpacking initramfs...
[ 7.423873] Freeing initrd memory: 1048K (ffffffc075dad000 - ffffffc075eb3000)
[ 7.425089] kvm [1]: interrupt-controller@1c84000 IRQ25
[ 7.425438] kvm [1]: timer IRQ27
[ 7.425457] kvm [1]: Hyp mode initialized successfully
[ 7.426833] lock super standby defaultly!
[ 7.426862] lookup_scene_lock_name: new scene lock super_standby
[ 7.426878] scene_lock_init name=super_standby
[ 7.426893] scene_lock: super_standby, type 5, count 1
[ 7.427552] audit: initializing netlink socket (disabled)
[ 7.427601] type=2000 audit(0.180:1): initialized
[ 7.428565] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 7.429023] VFS: Disk quotas dquot_6.5.2
[ 7.429150] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 7.429561] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 7.429945] NFS: Registering the id_resolver key type
[ 7.429995] Key type id_resolver registered
[ 7.430009] Key type id_legacy registered
[ 7.430028] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 7.430185] NTFS driver 2.1.30 [Flags: R/W].
[ 7.430449] fuse init (API version 7.22)
[ 7.430845] msgmni has been set to 3977
[ 7.431642] io scheduler noop registered
[ 7.431660] io scheduler deadline registered
[ 7.431704] io scheduler cfq registered (default)
[ 7.432523] [DISP]disp_module_init
[ 7.433067] [DISP] boot_disp:0x40a
[ 7.433646] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[ 7.433805] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[ 7.433990] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[ 7.435083] [DISP] fb_base:0x47400000
[ 7.442667] [DISP] Fb_map_kernel_logo,line:880:this is not a bmp picture.
[ 7.472553] Console: switching to colour frame buffer device 240x67
[ 7.501481] [DISP]disp_module_init finish
[ 7.502010] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
[ 7.502164] sw_console_setup()1173 - console setup baud 115200 parity n bits 8, flow n
[ 8.462880] console [ttyS0] enabled
[ 8.467358] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI
[ 8.474402] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI
[ 8.481516] uart3: ttyS3 at MMIO 0x1c28c00 (irq = 35) is a SUNXI
[ 8.488604] uart4: ttyS4 at MMIO 0x1c29000 (irq = 36) is a SUNXI
[ 8.495818] misc dump reg init
[ 8.499576] [drm] Initialized drm 1.1.0 20060810
[ 8.508213] loop: module loaded
[ 8.511994] sunxi-bt bt.27: Missing bt_power.
[ 8.516884] sunxi-bt bt.27: bt_power_name ((null))
[ 8.522244] sunxi-bt bt.27: io_regulator_name (vcc-wifi-io)
[ 8.528513] sunxi-bt bt.27: bt_rst gpio=356 mul-sel=1 pull=-1 drv_level=-1 data=0
[ 8.537313] sunxi-bt bt.27: clk not config
[ 8.542025] sunxi-bt bt.27: block state already is 1
[ 8.547884] sunxi-wlan wlan.26: wlan_busnum (1)
[ 8.552949] sunxi-wlan wlan.26: Missing wlan_power.
[ 8.558405] sunxi-wlan wlan.26: wlan_power_name ((null))
[ 8.564342] sunxi-wlan wlan.26: io_regulator_name (vcc-wifi-io)
[ 8.570990] sunxi-wlan wlan.26: wlan_regon gpio=354 mul-sel=1 pull=-1 drv_level=-1 data=0
[ 8.580557] sunxi-wlan wlan.26: wlan_hostwake gpio=355 mul-sel=6 pull=-1 drv_level=-1 data=0
[ 8.590408] sunxi-wlan wlan.26: clk not config
[ 8.596036] tun: Universal TUN/TAP device driver, 1.6
[ 8.601684] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 8.609312] WARNING: Get ephy clock is failed
[ 8.614851] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.622285] get ehci0-controller drv_vbus_gpio is fail
[ 8.628039] get ehci0-controller, regulator_io is no nocare
[ 8.634321] [sunxi-ehci0]: probe, pdev->name: 1c1a000.ehci0-controller, sunxi_ehci: 0xffffffc000be6730, 0x:ffffff80000ae000, irq_no:68
[ 8.647888] sunxi-ehci 1c1a000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.658020] sunxi-ehci 1c1a000.ehci0-controller: new USB bus registered, assigned bus number 1
[ 8.667949] sunxi-ehci 1c1a000.ehci0-controller: irq 104, io mem 0xffffffc0004c619c
[ 8.693401] sunxi-ehci 1c1a000.ehci0-controller: USB 0.0 started, EHCI 1.00
[ 8.701185] ehci_irq: highspeed device connect
[ 8.706733] hub 1-0:1.0: USB hub found
[ 8.716965] hub 1-0:1.0: 1 port detected
[ 8.727414] scene_lock_init name=ehci_standby
[ 8.738271] get ehci1-controller drv_vbus_gpio is fail
[ 8.749876] get ehci1-controller, regulator_io is no nocare
[ 8.761967] [sunxi-ehci1]: probe, pdev->name: 1c1b000.ehci1-controller, sunxi_ehci: 0xffffffc000be6980, 0x:ffffff80000b6000, irq_no:6a
[ 8.781493] sunxi-ehci 1c1b000.ehci1-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.797769] sunxi-ehci 1c1b000.ehci1-controller: new USB bus registered, assigned bus number 2
[ 8.813807] sunxi-ehci 1c1b000.ehci1-controller: irq 106, io mem 0xffffffc0004c619c
[ 8.841006] sunxi-ehci 1c1b000.ehci1-controller: USB 0.0 started, EHCI 1.00
[ 8.854918] ehci_irq: highspeed device connect
[ 8.866622] hub 2-0:1.0: USB hub found
[ 8.877038] hub 2-0:1.0: 1 port detected
[ 8.887760] scene_lock_init name=ehci_standby
[ 8.899122] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.912465] get ohci0-controller drv_vbus_gpio is fail
[ 8.924561] get ohci0-controller, regulator_io is no nocare
[ 8.937113] [sunxi-ohci0]: probe, pdev->name: 1c1a000.ohci0-controller, sunxi_ohci: 0xffffffc000be6290
[ 8.953844] sunxi-ohci 1c1a000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 8.969908] sunxi-ohci 1c1a000.ohci0-controller: new USB bus registered, assigned bus number 3
[ 8.985858] sunxi-ohci 1c1a000.ohci0-controller: irq 105, io mem 0x61ff726b6b64622c
[ 9.037811] usb 1-1: new high-speed USB device number 2 using sunxi-ehci
[ 9.061962] hub 3-0:1.0: USB hub found
[ 9.072417] hub 3-0:1.0: 1 port detected
[ 9.083130] scene_lock_init name=ohci_standby
[ 9.094230] get ohci1-controller drv_vbus_gpio is fail
[ 9.106081] get ohci1-controller, regulator_io is no nocare
[ 9.118438] [sunxi-ohci1]: probe, pdev->name: 1c1b000.ohci1-controller, sunxi_ohci: 0xffffffc000be64e0
[ 9.134979] sunxi-ohci 1c1b000.ohci1-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 9.150851] sunxi-ohci 1c1b000.ohci1-controller: new USB bus registered, assigned bus number 4
[ 9.166639] sunxi-ohci 1c1b000.ohci1-controller: irq 107, io mem 0x61ff726b6b64622c
[ 9.238984] hub 4-0:1.0: USB hub found
[ 9.249548] hub 4-0:1.0: 1 port detected
[ 9.260375] scene_lock_init name=ohci_standby
[ 9.272041] usbcore: registered new interface driver usb-storage
[ 9.285180] usbcore: registered new interface driver ums-alauda
[ 9.298161] usbcore: registered new interface driver ums-cypress
[ 9.311194] usbcore: registered new interface driver ums-datafab
[ 9.324143] usb 2-1: new high-speed USB device number 2 using sunxi-ehci
[ 9.337989] usbcore: registered new interface driver ums_eneub6250
[ 9.351262] usbcore: registered new interface driver ums-freecom
[ 9.364291] usbcore: registered new interface driver ums-isd200
[ 9.377162] usbcore: registered new interface driver ums-jumpshot
[ 9.390176] usbcore: registered new interface driver ums-karma
[ 9.402904] usbcore: registered new interface driver ums-onetouch
[ 9.415892] usbcore: registered new interface driver ums-realtek
[ 9.428723] usbcore: registered new interface driver ums-sddr09
[ 9.441372] usbcore: registered new interface driver ums-sddr55
[ 9.453917] usbcore: registered new interface driver ums-usbat
[ 9.466419] usbcore: registered new interface driver usbserial
[ 9.478720] usbcore: registered new interface driver usbserial_generic
[ 9.491738] usbserial: USB Serial support registered for generic
[ 9.504537] mousedev: PS/2 mouse device common for all mice
[ 9.517052] input: sunxi-keyboard as /devices/virtual/input/input0
[ 9.530360] sunxi-rtc 1f00000.rtc: rtc core: registered rtc-sunxi as rtc0
[ 9.543687] sunxi-rtc 1f00000.rtc: RTC enabled
[ 9.554316] hub 2-1:1.0: USB hub found
[ 9.563972] i2c /dev entries driver
[ 9.573223] hub 2-1:1.0: 4 ports detected
[ 9.619156] input: axp81x-supplyer as /devices/platform/axp81x_board/axp81x-supplyer.47/input/input1
[ 9.641587] sunxi budget cooling probe start !
[ 9.652108] CPU freq cooling register Success
[ 9.662452] CPU hotplug cooling register Success
[ 9.673256] CPU budget cooling register Success
[ 9.684256] sunxi gpu cooling probe start !
[ 9.694448] CPU gpu cooling register Success
[ 9.707699] cpuidle: using governor ladder
[ 9.716964] cpuidle: using governor menu
[ 9.726657] sunxi-mmc 1c0f000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.20 2015-7-13 16:28) Compiled in May 7 2016 at 12:34:27
[ 9.744326] sunxi-mmc 1c0f000.sdmmc: regulator prop vmmc,str none
[ 9.755757] sunxi-mmc 1c0f000.sdmmc: regulator prop vqmmc,str none
[ 9.767253] sunxi-mmc 1c0f000.sdmmc: regulator prop vdmmc,str vcc-sdc
[ 9.779006] sunxi-mmc 1c0f000.sdmmc: No vmmc regulator found
[ 9.789837] sunxi-mmc 1c0f000.sdmmc: No vqmmc regulator found
[ 9.801198] sunxi-mmc 1c0f000.sdmmc: Got CD GPIO #166.
[ 9.811652] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 9.827412] sunxi-mmc 1c0f000.sdmmc: no vqmmc,Check if there is regulator
[ 9.854519] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 9.884058] sunxi-mmc 1c0f000.sdmmc: base:0xffffff80000ca000 irq:92
[ 9.896028] sunxi-mmc 1c10000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.20 2015-7-13 16:28) Compiled in May 7 2016 at 12:34:27
[ 9.913738] sunxi-mmc 1c10000.sdmmc: Can't get vmmc regulator string
[ 9.925514] sunxi-mmc 1c10000.sdmmc: Can't get vqmmc regulator string
[ 9.937354] usb 2-1.4: new full-speed USB device number 3 using sunxi-ehci
[ 9.949647] sunxi-mmc 1c10000.sdmmc: Can't get vdmmc regulator string
[ 9.961467] get() with no identifier
[ 9.970167] get() with no identifier
[ 9.978806] get() with no identifier
[ 9.987380] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 52, RTO !!
[ 9.998827] sunxi-mmc 1c10000.sdmmc: No vmmc regulator found
[ 10.009681] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 52, RTO !!
[ 10.020919] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 10.020964] sunxi-mmc 1c10000.sdmmc: No vqmmc regulator found
[ 10.020967] sunxi-mmc 1c10000.sdmmc: No vdmmc regulator found
[ 10.060086] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 10.061160] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 10.063290] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !!
[ 10.064098] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !!
[ 10.064905] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !!
[ 10.065711] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !!
[ 10.066332] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B
[ 10.066372] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B
[ 10.068739] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B
[ 10.086163] mmc0: SD Status: Invalid Allocation Unit size.
[ 10.087832] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 10.089641] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B
[ 10.089681] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B
[ 10.089778] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 4 timing SD-HS(SDR25) dt B
[ 10.089797] mmc0: new high speed SDXC card at address 0007
[ 10.270095] sunxi-mmc 1c10000.sdmmc: no vqmmc,Check if there is regulator
[ 10.282830] mmcblk0: mmc0:0007 SD64G 58.2 GiB
[ 10.294263] mmcblk0: p1 p2
[ 10.297327] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 10.317019] sunxi-mmc 1c10000.sdmmc: base:0xffffff80000d2000 irq:93
[ 10.333376] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 10.346389] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 10.358475] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 10.375778] input: Logitech USB Receiver as /devices/soc.0/1c1b000.ehci1-controller/usb2/2-1/2-1.4/2-1.4:1.0/input/input2
[ 10.393627] hid-generic 0003:046D:C52B.0001: input: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-sunxi-ehci-1.4/input0
[ 10.394355] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 10.429142] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 8, RTO !!
[ 10.442323] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 10.455393] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 10.467977] input: Logitech USB Receiver as /devices/soc.0/1c1b000.ehci1-controller/usb2/2-1/2-1.4/2-1.4:1.1/input/input3
[ 10.485720] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 10.498521] hid-generic 0003:046D:C52B.0002: input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-sunxi-ehci-1.4/input1
[ 10.516792] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 10.530181] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !!
[ 10.543650] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !!
[ 10.557072] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !!
[ 10.569692] hid-generic 0003:046D:C52B.0003: device has no listeners, quitting
[ 10.583467] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !!
[ 10.595968] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 10.596127] usbcore: registered new interface driver usbhid
[ 10.596129] usbhid: USB HID core driver
[ 10.636447] usbcore: registered new interface driver snd-usb-audio
[ 10.649326] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 1, RTO !!
[ 10.662042] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[ 10.679611] sndhdmi sound.7: sndhdmi <-> 1c22800.daudio mapping ok
[ 10.693662] TCP: cubic registered
[ 10.703472] NET: Registered protocol family 10
[ 10.714932] sit: IPv6 over IPv4 tunneling driver
[ 10.726523] NET: Registered protocol family 17
[ 10.737350] Key type dns_resolver registered
[ 10.748094] Registering SWP/SWPB emulation handler
[ 10.759699] registered taskstats version 1
[ 10.770422] [DISP] boot_disp:0x40a
[ 10.780686] [HDMI] power vcc-hdmi-33
[ 10.790874] [HDMI] cec support = 0
[ 11.305332] [DISP] disp_device_attached,line:94:attched ok, mgr0<-->device1, type=4
[ 11.319797] sunxi-rtc 1f00000.rtc: setting system clock to 2016-07-04 21:00:13 UTC (1467666013)
[ 11.330545] [ehci0-controller]: sunxi_usb_disable_ehci
[ 11.330550] [sunxi-ehci0]: remove, pdev->name: 1c1a000.ehci0-controller, sunxi_ehci: 0xffffffc000be6730
[ 11.330563] scene_lock_destroy name=ehci_standby
[ 11.330569] sunxi-ehci 1c1a000.ehci0-controller: remove, state 1
[ 11.330586] usb usb1: USB disconnect, device number 1
[ 11.330590] usb 1-1: USB disconnect, device number 2
[ 11.411487] input: sunxi-ths as /devices/virtual/input/input4
[ 11.412093] sunxi-ehci 1c1a000.ehci0-controller: USB bus 1 deregistered
[ 11.412119] [ohci0-controller]: sunxi_usb_disable_ohci
[ 11.412123] [sunxi-ohci0]: remove, pdev->name: 1c1a000.ohci0-controller, sunxi_ohci: 0xffffffc000be6290
[ 11.412126] scene_lock_destroy name=ohci_standby
[ 11.412131] sunxi-ohci 1c1a000.ohci0-controller: remove, state 4
[ 11.412144] usb usb3: USB disconnect, device number 1
[ 11.415052] ohci_irq: fullspeed or lowspeed device connect
[ 11.515222] sunxi-ohci 1c1a000.ohci0-controller: USB bus 3 deregistered
[ 11.515262] thermal thermal_zone0: failed to read out thermal zone 0
[ 11.542417] [ehci0-controller]: sunxi_usb_enable_ehci
[ 11.542468] ALSA device list:
[ 11.542470] #0: sndhdmi
[ 11.573175] [sunxi-ehci0]: probe, pdev->name: 1c1a000.ehci0-controller, sunxi_ehci: 0xffffffc000be6730, 0x:ffffff80000ae000, irq_no:68
[ 11.586693] Freeing unused kernel memory: 484K (ffffffc00096c000 - ffffffc0009e5000)
[ 11.605977] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[ 11.606857] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[ 11.642359] sunxi-ehci 1c1a000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 11.659158] sunxi-ehci 1c1a000.ehci0-controller: new USB bus registered, assigned bus number 1
[ 11.675619] sunxi-ehci 1c1a000.ehci0-controller: irq 104, io mem 0xffffffc0006c1ecc
[ 11.700472] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 11.704449] sunxi-ehci 1c1a000.ehci0-controller: USB 0.0 started, EHCI 1.00
[ 11.704454] ehci_irq: highspeed device connect
[ 11.705087] hub 1-0:1.0: USB hub found
[ 11.705100] hub 1-0:1.0: 1 port detected
[ 11.705235] scene_lock_init name=ehci_standby
[ 11.705238] [ohci0-controller]: sunxi_usb_enable_ohci
[ 11.705243] [sunxi-ohci0]: probe, pdev->name: 1c1a000.ohci0-controller, sunxi_ohci: 0xffffffc000be6290
[ 11.705285] sunxi-ohci 1c1a000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 11.705299] sunxi-ohci 1c1a000.ohci0-controller: new USB bus registered, assigned bus number 3
[ 11.705333] sunxi-ohci 1c1a000.ohci0-controller: irq 105, io mem 0xffffffc0006c1ecc
[ 11.767860] hub 3-0:1.0: USB hub found
[ 11.767875] hub 3-0:1.0: 1 port detected
[ 11.767982] scene_lock_init name=ohci_standby
[ 12.019361] usb 1-1: new high-speed USB device number 2 using sunxi-ehci
[ 12.126907] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[ 12.148404] systemd[1]: Detected architecture 'arm64'.
[ 12.207728] systemd[1]: Set hostname to <pine64pro>.
[ 12.509115] systemd[1]: Expecting device dev-ttyS0.device...
[ 12.540973] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 12.555922] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 12.570618] systemd[1]: Starting Remote File Systems (Pre).
[ 12.599937] systemd[1]: Reached target Remote File Systems (Pre).
[ 12.612921] systemd[1]: Starting Encrypted Volumes.
[ 12.639277] systemd[1]: Reached target Encrypted Volumes.
[ 12.651441] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 12.666614] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 12.681624] systemd[1]: Starting Paths.
[ 12.708160] systemd[1]: Reached target Paths.
[ 12.719272] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 12.735999] systemd[1]: Starting Swap.
[ 12.767202] systemd[1]: Reached target Swap.
[ 12.778309] systemd[1]: Expecting device dev-mmcblk0p1.device...
[ 12.806564] systemd[1]: Starting Root Slice.
[ 12.836083] systemd[1]: Created slice Root Slice.
[ 12.847564] systemd[1]: Starting User and Session Slice.
[ 12.875444] systemd[1]: Created slice User and Session Slice.
[ 12.887940] systemd[1]: Starting Delayed Shutdown Socket.
[ 12.914814] systemd[1]: Listening on Delayed Shutdown Socket.
[ 12.927218] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 12.964012] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 12.977795] systemd[1]: Starting Journal Socket (/dev/log).
[ 13.013203] systemd[1]: Listening on Journal Socket (/dev/log).
[ 13.025833] systemd[1]: Starting udev Control Socket.
[ 13.052567] systemd[1]: Listening on udev Control Socket.
[ 13.064474] systemd[1]: Starting udev Kernel Socket.
[ 13.091924] systemd[1]: Listening on udev Kernel Socket.
[ 13.103653] systemd[1]: Starting Journal Socket.
[ 13.131285] systemd[1]: Listening on Journal Socket.
[ 13.142670] systemd[1]: Starting System Slice.
[ 13.170673] systemd[1]: Created slice System Slice.
[ 13.181816] systemd[1]: Started File System Check on Root Device.
[ 13.194206] systemd[1]: Starting system-systemd\x2dfsck.slice.
[ 13.229695] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 13.242342] systemd[1]: Starting system-getty.slice.
[ 13.269051] systemd[1]: Created slice system-getty.slice.
[ 13.280460] systemd[1]: Starting system-serial\x2dgetty.slice.
[ 13.308404] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 13.320871] systemd[1]: Starting Increase datagram queue length...
[ 13.349366] systemd[1]: Starting Restore / save the current clock...
[ 13.384826] systemd[1]: Starting Initialize Sunxi disp2 HDMI output mode...
[ 13.418785] systemd[1]: Mounting Huge Pages File System...
[ 13.465589] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 13.556060] systemd[1]: Started Set Up Additional Binary Formats.
[ 13.575412] hdmi_clk_disable_prepare()L176
[ 13.589312] systemd[1]: Starting Load Kernel Modules...
[ 13.624869] systemd[1]: Mounting POSIX Message Queue File System...
[ 13.654307] systemd[1]: Starting udev Coldplug all Devices...
[ 13.684191] systemd[1]: Mounting Debug File System...
[ 13.713665] systemd[1]: Starting Slices.
[ 13.741448] systemd[1]: Reached target Slices.
[ 13.771022] systemd[1]: Mounted Debug File System.
[ 13.800533] systemd[1]: Mounted POSIX Message Queue File System.
[ 13.812466] hdmi_clk_enable_prepare()L161
[ 13.839855] systemd[1]: Mounted Huge Pages File System.
[ 13.918579] systemd[1]: Started Increase datagram queue length.
[ 13.948107] systemd[1]: Started Restore / save the current clock.
[ 13.977616] systemd[1]: Started Initialize Sunxi disp2 HDMI output mode.
[ 14.007149] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 14.064568] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 14.098055] systemd[1]: Starting Syslog Socket.
[ 14.109633] cfg80211: Calling CRDA to update world regulatory domain
[ 14.125222] systemd[1]: Listening on Syslog Socket.
[ 14.134248] systemd[1]: Starting Journal Service...
[ 14.175507] systemd[1]: Started Journal Service.
[ 14.314292] RTL871X: module init start
[ 14.321956] RTL871X: rtl8723bs v4.3.16_13854.20150410_BTCOEX20150119-5844
[ 14.332955] RTL871X: build time: May 7 2016 12:47:20
[ 14.341979] RTL871X: rtl8723bs BT-Coex version = BTCOEX20150119-5844
[ 14.353095] sunxi-wlan wlan.26: bus_index: 1
[ 14.361474] sunxi-wlan wlan.26: check wlan io_regulator voltage: 1800000
[ 14.410494] systemd-udevd[1485]: starting version 215
[ 14.480806] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 14.481009] RTL871X: module init ret=0
[ 14.505732] sunxi-mmc 1c10000.sdmmc: no vqmmc,Check if there is regulator
[ 14.528567] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 14.558886] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 14.570336] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 14.580962] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 14.598874] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 14.618279] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 8, RTO !!
[ 14.631426] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 14.643088] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 14.654308] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 14.665578] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 14.676832] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !!
[ 14.688075] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !!
[ 14.699221] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !!
[ 14.712035] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !!
[ 14.722756] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 14.738522] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 1, RTO !!
[ 14.748659] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[ 15.118518] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 15.358548] sunxi_ss_alg_register()681 - crypto_register_ahash(md5) failed! return -22
[ 15.371192] sunxi_ss_probe()793 - sunxi_ss_alg_register() failed! return -22
[ 15.382850] ss: probe of 1c15000.ce failed with error -22
[ 15.437991] sunxi cedar version 0.1
[ 15.445893] [cedar]: install start!!!
[ 15.453679] ycy the get irq is 90
[ 15.463350] ycy clk_bass_vir 0x18 is ffffff8001564018, the value:3006207
[ 15.474715] ycy clk_bass_vir 0x13c is ffffff800156413c, the value:0
[ 15.485499] ycy clk_bass_vir 0x64 is ffffff8001564064, the value:601810
[ 15.505901] ycy clk_bass_vir 0x2c4 is ffffff80015642c4, the value:601c10
[ 15.518528] ycy clk_bass_vir 0x100 is ffffff8001564100, the value:0
[ 15.522384] sunxi-bt bt.27: block state already is 1
[ 15.538769] [cedar]: install end!!!
[ 15.784372] Mali: Set gpu frequency to 408 MHz
[ 15.793175] Mali: Init Mali gpu clocks successfully
[ 15.803063] gpu cooling callback register Success
[ 15.814036] Mali: Mali device driver loaded
[ 16.032763] cfg80211: World regulatory domain updated:
[ 16.042014] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 16.054970] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 16.066735] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 16.078398] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 16.090071] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 16.101932] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 16.113476] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[ 16.125463] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 16.136899] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 16.261125] [VFE]cci probe end cci_sel = 0!
[ 16.272999] [VFE]cci_init end
[ 16.450997] [VFE]Welcome to Video Front End driver
[ 16.459665] [VFE]csi probe end csi_sel = 0!
[ 16.467798] [VFE]csi_init end
[ 16.474668] [VFE]isp probe start isp_sel = 0!
[ 16.483360] [ISP] isp platform_id = 3!
[ 16.490629] [VFE]isp probe end isp_sel = 0!
[ 16.498919] [VFE]sunxi_isp_platform_register end
[ 16.508358] [VFE]mipi probe start mipi_sel = 0!
[ 16.516694] [VFE]mipi probe end mipi_sel = 0!
[ 16.525013] [VFE]mipi_init end
[ 16.531671] [VFE]flash_init end
[ 16.539789] [VFE]pdev->id = 0
[ 16.546252] [VFE]dev->vip_sel = 0
[ 16.553074] [VFE_WARN]fetch csi0_dev0_twi_id from device_tree failed
[ 16.563284] [VFE_WARN]fetch csi0_dev0_afvdd from device_tree failed
[ 16.573271] [VFE_WARN]fetch csi0_dev0_afvdd_vol from device_tree failed
[ 16.583619] [VFE_WARN]fetch csi0_dev0_power_en from device_tree failed
[ 16.593840] [VFE_WARN]fetch csi0_dev0_flash_en from device_tree failed
[ 16.603921] [VFE_WARN]fetch csi0_dev0_flash_mode from device_tree failed
[ 16.614194] [VFE_WARN]fetch csi0_dev0_af_pwdn from device_tree failed
[ 16.624098] [VFE_WARN]fetch csi0_dev1_twi_id from device_tree failed
[ 16.634034] [VFE_WARN]fetch csi0_dev1_afvdd from device_tree failed
[ 16.643763] [VFE_WARN]fetch csi0_dev1_afvdd_vol from device_tree failed
[ 16.653838] [VFE_WARN]fetch csi0_dev1_power_en from device_tree failed
[ 16.663906] [VFE_WARN]fetch csi0_dev1_flash_en from device_tree failed
[ 16.673889] [VFE_WARN]fetch csi0_dev1_flash_mode from device_tree failed
[ 16.685322] [VFE_WARN]fetch csi0_dev1_af_pwdn from device_tree failed
[ 16.695212] [VFE]fetch rear sensor list info start!
[ 16.703276] [VFE]Fetch sensor list form"/system/etc/hawkview/sensor_list_cfg.ini"
[ 16.749932] [vfe_warn]open file failed!
[ 16.794732] [VFE]fetch rear sensor list info end!
[ 16.802801] [VFE]fetch front sensor list info start!
[ 16.811011] [VFE]Fetch sensor list form"/system/etc/hawkview/sensor_list_cfg.ini"
[ 16.857613] [vfe_warn]open file failed!
[ 16.902774] [VFE]fetch front sensor list info end!
[ 16.911115] [VFE_WARN]os_gpio_request failed, gpio=129, ret=0xfffffff0, -16
[ 16.922134] [VFE]vfe_init end
[ 16.929511] [VFE]probe_work_handle start!
[ 16.937358] [VFE]vfe_runtime_resume
[ 16.956777] [VFE]..........................vfe clk open!.......................
[ 16.967970] [VFE_WARN]vfe dphy clock is null
[ 16.975773] [VFE]v4l2 subdev register input_num = 0
[ 16.984937] [VFE]vfe sensor detect start! input_num = 0
[ 16.993721] [VFE_WARN]NOT found this item: hm5065, you can add this sensor in the sensor_list_t!
[ 17.006722] [VFE]Sub device register "hm5065" i2c_addr = 0x3e start!
[ 17.016959] [VFE_ERR]Error registering v4l2 subdevice No such device!
[ 17.028310] [VFE_ERR]vfe sensor register check error at input_num = 0
[ 17.038646] [VFE]v4l2 subdev register input_num = 1
[ 17.047296] axp81x_aldo1: Failed to create debugfs directory
[ 17.056816] axp81x_dldo3: Failed to create debugfs directory
[ 17.067097] axp81x_eldo3: Failed to create debugfs directory
[ 17.076522] axp81x_aldo1: Failed to create debugfs directory
[ 17.085952] [VFE]vfe sensor detect start! input_num = 1
[ 17.091405] systemd-journald[1482]: Received request to flush runtime journal from PID 1
[ 17.107183] [VFE_WARN]NOT found this item: gc2145, you can add this sensor in the sensor_list_t!
[ 17.120379] [VFE]Sub device register "gc2145" i2c_addr = 0x78 start!
[ 17.131678] [VFE_ERR]Error registering v4l2 subdevice No such device!
[ 17.142318] [VFE_ERR]vfe sensor register check error at input_num = 1
[ 17.153008] [VFE]V4L2 device registered as (null)
[ 17.161868] [VFE]vfe_runtime_suspend
[ 17.169409] [VFE]..........................vfe clk close!.......................
[ 17.181625] [VFE]probe_work_handle end!
[ 17.411672] gpu cooling callback set freq limit 0
[ 18.166362] rtl8192cu: Chip version 0x10
[ 18.267700] rtl8192cu: MAC address: 80:3f:5d:f3:44:01
[ 18.277013] rtl8192cu: Board Type 0
[ 18.285039] rtlwifi: rx_max_size 15360, rx_urb_num 8, in_ep 1
[ 18.295218] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
[ 18.306437] usbcore: registered new interface driver rtl8192cu
[ 18.319952] rtlwifi: Loading alternative firmware rtlwifi/rtl8192cufw.bin
[ 18.332110] rtlwifi: Firmware rtlwifi/rtl8192cufw_TMSC.bin not available
[ 18.944513] libphy: 1c30000.eth: probed
[ 18.952837] sunxi-gmac 1c30000.eth eth0: eth0: PHY ID 001cc915 at 0 IRQ poll (1c30000.eth-0:00)
[ 23.866851] libphy: 1c30000.eth-0:00 - Link is Up - 1000/Full
[ 44.380582] [DISP] disp_ioctl,line:1558:para err in disp_ioctl, cmd = 0x0,screen id = 65536
|
