Armbian on Quartz64
#17
Here is the boot log:
Code:
DDR Version V1.10 20210810
ln
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=8 Size=8192MB
tdqss: cs0 dqs0: 72ps, dqs1: -96ps, dqs2: -72ps, dqs3: -168ps,
tdqss: cs1 dqs0: 72ps, dqs1: -96ps, dqs2: -48ps, dqs3: -144ps,

change to: 324MHz
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x61

change to: 528MHz
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58

change to: 780MHz
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58

change to: 1560MHz(final freq)
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:22%
dram drv:40,odt:80
vref_ca:00000071
clk skew:0x26
cs 0:
the read training result:
DQS0:0x37, DQS1:0x31, DQS2:0x39, DQS3:0x30,
min  :0x12 0x14 0x17 0x12  0x1  0x8  0x9  0x8 , 0x8  0x8  0x4  0x1  0xf  0xb 0x11  0xa ,
      0x14 0x13  0xe  0xc  0x8  0x2  0x4  0x6 ,0x10  0xb  0xc  0x3 0x13 0x12  0xe 0x13 ,
mid  :0x2d 0x2d 0x31 0x2c 0x1c 0x22 0x23 0x21 ,0x23 0x23 0x1d 0x1a 0x28 0x27 0x29 0x25 ,
      0x30 0x2f 0x29 0x28 0x22 0x1c 0x1f 0x20 ,0x29 0x25 0x24 0x1e 0x2c 0x2a 0x28 0x2c ,
max  :0x48 0x47 0x4b 0x47 0x37 0x3d 0x3e 0x3b ,0x3e 0x3e 0x36 0x34 0x41 0x43 0x42 0x41 ,
      0x4d 0x4b 0x44 0x45 0x3d 0x37 0x3a 0x3b ,0x43 0x3f 0x3d 0x39 0x45 0x43 0x43 0x45 ,
range:0x36 0x33 0x34 0x35 0x36 0x35 0x35 0x33 ,0x36 0x36 0x32 0x33 0x32 0x38 0x31 0x37 ,
      0x39 0x38 0x36 0x39 0x35 0x35 0x36 0x35 ,0x33 0x34 0x31 0x36 0x32 0x31 0x35 0x32 ,
the write training result:
DQS0:0x34, DQS1:0x13, DQS2:0x18, DQS3:0x5,
min  :0x7f 0x84 0x87 0x85 0x71 0x76 0x78 0x7a 0x7a ,0x52 0x57 0x50 0x50 0x57 0x5a 0x5a 0x59 0x52 ,
      0x63 0x64 0x5f 0x5e 0x56 0x52 0x53 0x5a 0x5d ,0x4b 0x4a 0x48 0x44 0x4e 0x4e 0x4c 0x52 0x49 ,
mid  :0x9a 0x9d 0xa0 0x9c 0x89 0x8d 0x91 0x91 0x90 ,0x6e 0x6d 0x66 0x69 0x70 0x71 0x71 0x72 0x6c ,
      0x7f 0x7e 0x76 0x77 0x6f 0x6a 0x6c 0x72 0x76 ,0x66 0x62 0x5f 0x5b 0x67 0x69 0x62 0x6a 0x60 ,
max  :0xb5 0xb7 0xb9 0xb4 0xa1 0xa5 0xab 0xa9 0xa7 ,0x8a 0x84 0x7d 0x82 0x8a 0x89 0x89 0x8b 0x87 ,
      0x9b 0x98 0x8d 0x90 0x89 0x82 0x86 0x8b 0x8f ,0x81 0x7a 0x77 0x73 0x80 0x85 0x79 0x83 0x77 ,
range:0x36 0x33 0x32 0x2f 0x30 0x2f 0x33 0x2f 0x2d ,0x38 0x2d 0x2d 0x32 0x33 0x2f 0x2f 0x32 0x35 ,
      0x38 0x34 0x2e 0x32 0x33 0x30 0x33 0x31 0x32 ,0x36 0x30 0x2f 0x2f 0x32 0x37 0x2d 0x31 0x2e ,
cs 1:
the read training result:
DQS0:0x34, DQS1:0x34, DQS2:0x37, DQS3:0x30,
min  :0x10 0x12 0x14  0xf  0x2  0x4  0xa  0x4 , 0xb  0x9  0x6  0x2 0x11  0xe 0x12  0xc ,
      0x14 0x12  0xe  0xb  0x8  0x1  0x3  0x6 , 0xe  0x8  0xa  0x1 0x11  0xf  0xd 0x11 ,
mid  :0x2a 0x2b 0x2e 0x2a 0x1c 0x1f 0x23 0x1f ,0x26 0x25 0x20 0x1d 0x2b 0x2a 0x2c 0x28 ,
      0x2f 0x2d 0x28 0x27 0x22 0x1c 0x1e 0x20 ,0x28 0x23 0x22 0x1d 0x2b 0x2a 0x27 0x2b ,
max  :0x45 0x45 0x48 0x46 0x36 0x3b 0x3c 0x3a ,0x41 0x41 0x3a 0x38 0x45 0x46 0x46 0x45 ,
      0x4b 0x49 0x43 0x43 0x3d 0x37 0x39 0x3b ,0x42 0x3e 0x3b 0x39 0x45 0x45 0x42 0x45 ,
range:0x35 0x33 0x34 0x37 0x34 0x37 0x32 0x36 ,0x36 0x38 0x34 0x36 0x34 0x38 0x34 0x39 ,
      0x37 0x37 0x35 0x38 0x35 0x36 0x36 0x35 ,0x34 0x36 0x31 0x38 0x34 0x36 0x35 0x34 ,
the write training result:
DQS0:0x34, DQS1:0x13, DQS2:0x18, DQS3:0x5,
min  :0x7a 0x82 0x82 0x7c 0x6e 0x71 0x74 0x76 0x76 ,0x55 0x56 0x52 0x52 0x59 0x5a 0x5c 0x5c 0x56 ,
      0x65 0x67 0x60 0x60 0x57 0x54 0x56 0x5c 0x5d ,0x55 0x54 0x50 0x4d 0x56 0x58 0x56 0x5b 0x52 ,
mid  :0x96 0x9a 0x9c 0x97 0x83 0x89 0x8e 0x8e 0x8c ,0x71 0x70 0x6a 0x6a 0x73 0x73 0x74 0x74 0x6f ,
      0x81 0x81 0x78 0x79 0x70 0x6b 0x6e 0x74 0x76 ,0x6f 0x6c 0x69 0x64 0x6f 0x72 0x6f 0x74 0x6c ,
max  :0xb2 0xb3 0xb6 0xb2 0x99 0xa2 0xa8 0xa6 0xa3 ,0x8d 0x8a 0x83 0x83 0x8d 0x8d 0x8d 0x8d 0x89 ,
      0x9e 0x9b 0x91 0x93 0x89 0x83 0x87 0x8d 0x8f ,0x8a 0x84 0x82 0x7b 0x89 0x8d 0x88 0x8e 0x86 ,
range:0x38 0x31 0x34 0x36 0x2b 0x31 0x34 0x30 0x2d ,0x38 0x34 0x31 0x31 0x34 0x33 0x31 0x31 0x33 ,
      0x39 0x34 0x31 0x33 0x32 0x2f 0x31 0x31 0x32 ,0x35 0x30 0x32 0x2e 0x33 0x35 0x32 0x33 0x34 ,
CA Training result:
cs:0 min  :0x59 0x62 0x4d 0x49 0x4d 0x49 0x54 ,0x54 0x52 0x4b 0x4b 0x4b 0x45 0x54 ,
cs:0 mid  :0x97 0x9d 0x89 0x85 0x89 0x85 0x82 ,0x90 0x8e 0x88 0x87 0x86 0x82 0x80 ,
cs:0 max  :0xd5 0xd8 0xc6 0xc2 0xc5 0xc1 0xb1 ,0xcd 0xcb 0xc6 0xc4 0xc2 0xbf 0xac ,
cs:0 range:0x7c 0x76 0x79 0x79 0x78 0x78 0x5d ,0x79 0x79 0x7b 0x79 0x77 0x7a 0x58 ,
cs:1 min  :0x56 0x64 0x49 0x4e 0x4b 0x4e 0x53 ,0x51 0x57 0x4b 0x50 0x4a 0x47 0x51 ,
cs:1 mid  :0x97 0x9d 0x8a 0x87 0x8a 0x85 0x83 ,0x92 0x91 0x8a 0x87 0x88 0x82 0x81 ,
cs:1 max  :0xd9 0xd7 0xcb 0xc1 0xca 0xbd 0xb3 ,0xd4 0xcb 0xc9 0xbf 0xc6 0xbd 0xb1 ,
cs:1 range:0x83 0x73 0x82 0x73 0x7f 0x6f 0x60 ,0x83 0x74 0x7e 0x6f 0x7c 0x76 0x60 ,
out
U-Boot SPL board init
U-Boot SPL 2017.09-armbian (Jan 08 2022 - 14:45:06)
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(5938a9cdfc...) + OK
## Checking uboot 0x00a00000 ... sha256(641fb675b2...) + OK
## Checking fdt 0x00b204f8 ... sha256(74e6edd8a8...) + OK
## Checking atf-2 0x00068000 ... sha256(0965dc8022...) + OK
## Checking atf-3 0xfdcd0000 ... sha256(be991af043...) + OK
## Checking atf-4 0xfdcc9000 ... sha256(695349eb36...) + OK
## Checking atf-5 0x00066000 ... sha256(315a4195a9...) + OK
## Checking optee 0x08400000 ... sha256(b8cddafab0...) + OK
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000)
Total: 256.502 ms

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-167-g81e0b993a-dirty:xsf
NOTICE:  BL31: Built : 11:20:08, Sep  6 2021
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    pmu v1 is valid
INFO:    dfs DDR fsp_param[0].freq_mhz= 1560MHz
INFO:    dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO:    dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO:    dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
I/TC:
I/TC: Start rockchip platform init
I/TC: Rockchip release version: 1.0
I/TC: OP-TEE version: 3.6.0-307-g0b06ae94 #1 Fri May  7 01:52:27 UTC 2021 aarch64
I/TC: Initialized
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0xa00000
INFO:    SPSR = 0x3c9


U-Boot 2017.09-armbian (Jan 08 2022 - 14:45:06 +0300)

Model: Firefly RK3566 Board
PreSerial: 2, raw, 0xfe660000
DRAM:  7.7 GiB
Sysmem: init
Relocation Offset: ed358000
Relocation fdt: eb9f81d0 - eb9fecd8
CR: M/C/I
Using default environment

no mmc device at slot 1
dwmmc@fe2b0000: 1 (SD), dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 1
MMC1: Legacy, 52Mhz
PartType: EFI
No misc partition
boot mode: None
FIT: No boot partition
No resource partition
No resource partition
Failed to load DTB, ret=-19
Failed to get kernel dtb, ret=-19
io-domain: OK
Model: Firefly RK3566 Board
rockchip_set_serialno: could not nc kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
  apll 816000 KHz
  dpll 780000 KHz
  gpll 1188000 KHz
  cpll 1000000 KHz
  npll 24000 KHz
  vpll 24000 KHz
  hpll 24000 KHz
  ppll 100000 KHz
  armclk 816000 KHz
  aclk_bus 150000 KHz
  pclk_bus 50000 KHz
  aclk_top_high 300000 KHz
  aclk_top_low 200000 KHz
  hclk_top 150000 KHz
  pclk_top 50000 KHz
  aclk_perimid 300000 KHz
  hclk_perimid 150000 KHz
  pclk_pmu 50000 KHz
Net:   No ethernet found.
Hit key to stop autoboot('Cnge FIT: No boot partition
FIT: No FIT image
Could not find misc partition
ANDROID: reboot reason: "(none)"
optee api revision: 2.0
TEEC: Waring: Could not  images, AVB skip
android_image_load_by_partname: Can't find part: boot
Android image load failed
Android boot failed, error -1.
starting USB...
Bus dwc3@fcc00000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3@fd000000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus dwc3@fcc00000 for devices... 1 USB Device(s) found
scanning bus dwc3@fd000000 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
340 bytes read in 14 ms (23.4 KiB/s)
1:    Armbian
Retrieving file: /boot/uInitrd
14039021 bytes read in 1204 ms (11.1 MiB/s)
Retrieving file: /boot/Image
34912768 bytes read in 2943 ms (11.3 MiB/s)
append: root=UUID=c22eb3a0-f780-48c9-adb5-37954715ba19 console=ttyS02,1500000 console=tty0 rootflags=data=writeback rw no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 bootsplash.bootfile=bootsplash.armbian
Retrieving file: /boot/dtb/rockchip/rk3566-quartz64-a.dtb
105527 bytes read in 84 ms (1.2 MiB/s)
Fdt Ramdisk skip relocation
sacy Image at 0a200000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    14038957 Bytes = 13.4 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 0x0a100000
   Booting using the fdt blob at 0x0a100000
   Using Device Tree in place at 000000000a100000, end 000000000a11cc36
can't found rockchip,drm-logo, use rockchip,fb-logo
WARNING: could not set reg FDT_ERR_BADOFFSET.
failed to reserve fb-loader-logo memory
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Total: 8109.608 ms

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[    0.000000] Linux version 5.16.0-rc8-media (root@vbox) (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321) #trunk SMP PREEMPT Sat Jan 8 10:58:33 MSK 2022
[    0.000000] Machine model: Pine64 RK3566 Quartz64-A Board
[    0.000000] efi: UEFI not found.
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x00000001ffffffff]
[    0.000000] NUMA: NODE_DATA [mem 0x1feff8a40-0x1feffafff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000200000-0x00000000ffffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   [mem 0x0000000100000000-0x00000001ffffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000200000-0x00000000083fffff]
[    0.000000]   node   0: [mem 0x0000000009400000-0x00000000efffffff]
[    0.000000]   node   0: [mem 0x0000000100000000-0x00000001ffffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x00000001ffffffff]
[    0.000000] On node 0, zone DMA: 512 pages in unavailable ranges
[    0.000000] On node 0, zone DMA: 4096 pages in unavailable ranges
[    0.000000] cma: Reserved 384 MiB at 0x00000000d8000000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS migration not required
[    0.000000] psci: SMC Calling Convention v1.2
[    0.000000] percpu: Embedded 30 pages/cpu s82200 r8192 d32488 u122880
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] CPU features: detected: Virtualization Host Extensions
[    0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    0.000000] alternatives: patching kernel code
[    0.000000] Fallback order for Node 0: 0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1995336
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: root=UUID=c22eb3a0-f780-48c9-adb5-37954715ba19 console=ttyS02,1500000 console=tty0 rootflags=data=writeback rw no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 bootsplash.bootfile=bootsplash.armbian
[    0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[    0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000] software IO TLB: mapped [mem 0x00000000d4000000-0x00000000d8000000] (64MB)
[    0.000000] Memory: 7443592K/8108032K available (17984K kernel code, 3310K rwdata, 7828K rodata, 4864K init, 771K bss, 271224K reserved, 393216K cma-reserved)
[    0.000000] random: get_random_u64 called from cache_random_seq_create+0x84/0x180 with crng_init=0
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] trace event string verifier disabled
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[    0.000000]     Trampoline variant of Tasks RCU enabled.
[    0.000000]     Rude variant of Tasks RCU enabled.
[    0.000000]     Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 320 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] GICv3: MBI range [296:319]
[    0.000000] GICv3: Using MBI frame 0x00000000fd410000
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GICv3: 16 PPIs implemented
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000
[    0.000000] ITS: No ITS available, not enabling LPIs
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.002005] Console: colour dummy device 80x25
[    0.002771] printk: console [tty0] enabled
[    0.002927] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.002972] pid_max: default: 32768 minimum: 301
[    0.003154] LSM: Security Framework initializing
[    0.003212] Yama: becoming mindful.
[    0.003364] AppArmor: AppArmor initialized
[    0.003554] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.003628] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.006916] rcu: Hierarchical SRCU implementation.
[    0.013637] EFI services will not be available.
[    0.014322] smp: Bringing up secondary CPUs ...
[    0.015464] Detected VIPT I-cache on CPU1
[    0.015518] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000
[    0.015591] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[    0.016919] Detected VIPT I-cache on CPU2
[    0.016969] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000
[    0.017028] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[    0.018267] Detected VIPT I-cache on CPU3
[    0.018314] GICv3: CPU3: found redistributor 300 region 0:0x00000000fd4c0000
[    0.018371] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[    0.018563] smp: Brought up 1 node, 4 CPUs
[    0.018707] SMP: Total of 4 processors activated.
[    0.018727] CPU features: detected: 32-bit EL0 Support
[    0.018743] CPU features: detected: 32-bit EL1 Support
[    0.018762] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[    0.018786] CPU features: detected: Common not Private translations
[    0.018803] CPU features: detected: CRC32 instructions
[    0.018821] CPU features: detected: RCpc load-acquire (LDAPR)
[    0.018837] CPU features: detected: LSE atomic instructions
[    0.018854] CPU features: detected: Privileged Access Never
[    0.018870] CPU features: detected: RAS Extension Support
[    0.018889] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[    0.062092] CPU: All CPU(s) started at EL2
[    0.066546] devtmpfs: initialized
[    0.092415] Registered cp15_barrier emulation handler
[    0.092475] Registered setend emulation handler
[    0.092507] KASLR disabled due to lack of seed
[    0.092878] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.092950] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.104914] pinctrl core: initialized pinctrl subsystem
[    0.106013] DMI not present or invalid.
[    0.106798] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.110832] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations
[    0.112034] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.114358] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.114543] audit: initializing netlink subsys (disabled)
[    0.114925] audit: type=2000 audit(0.112:1): state=initialized audit_enabled=0 res=1
[    0.117638] thermal_sys: Registered thermal governor 'fair_share'
[    0.117656] thermal_sys: Registered thermal governor 'bang_bang'
[    0.117688] thermal_sys: Registered thermal governor 'step_wise'
[    0.117707] thermal_sys: Registered thermal governor 'user_space'
[    0.117726] thermal_sys: Registered thermal governor 'power_allocator'
[    0.118640] cpuidle: using governor ladder
[    0.118723] cpuidle: using governor menu
[    0.119307] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.119546] ASID allocator initialised with 65536 entries
[    0.121681] Serial: AMBA PL011 UART driver
[    0.140637] platform fe0a0000.hdmi: Fixing up cyclic dependency with fe040000.vop
[    0.184196] rockchip-gpio fdd60000.gpio: probed /pinctrl/gpio@fdd60000
[    0.185263] rockchip-gpio fe740000.gpio: probed /pinctrl/gpio@fe740000
[    0.186401] rockchip-gpio fe750000.gpio: probed /pinctrl/gpio@fe750000
[    0.187467] rockchip-gpio fe760000.gpio: probed /pinctrl/gpio@fe760000
[    0.188498] rockchip-gpio fe770000.gpio: probed /pinctrl/gpio@fe770000
[    0.191278] platform hdmi-con: Fixing up cyclic dependency with fe0a0000.hdmi
[    0.220007] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.220059] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.220082] HugeTLB registered 2.00 MiB page s1 0 pages
[    0.220103] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    0.221229] cryptd: max_cpu_qlen set to 1000
[    0.289438] raid6: neonx8   gen()  1372 MB/s
[    0.357615] raid6: neonx8   xor()  1081 MB/s
[    0.425801] raid6: neonx4   gen()  1398 MB/s
[    0.493956] raid6: neonx4   xor()  1073 MB/s
[    0.562169] raid6: neonx2   gen()  1280 MB/s
[    0.630343] raid6: neonx2   xor()   985 MB/s
[    0.698585] raid6: neonx1   gen()  1055 MB/s
[    0.766716] raid6: neonx1   xor()   833 MB/s
[    0.835034] raid6: int64x8  gen()  1015 MB/s
[    0.903122] raid6: int64x8  xor()   528 MB/s
[    0.971324] raid6: int64x4  gen()  1078 MB/s
[    1.039502] raid6: int64x4  xor()   569 MB/s
[    1.107739] raid6: int64x2  gen()   962 MB/s
[    1.175868] raid6: int64x2  xor()   514 MB/s
[    1.244107] raid6: int64x1  gen()   694 MB/s
[    1.312269] raid6: int64x1  xor()   381 MB/s
[    1.312293] raid6: using algorithm neonx4 gen() 1398 MB/s
[    1.312313] raid6: .... xor() 1073 MB/s, rmw enabled
[    1.312330] raid6: using neon recovery algorithm
[    1.313603] ACPI: Interpreter disabled.
[    1.318235] iommu: Default domain type: Translated
[    1.318275] iommu: DMA domain TLB invalidation policy: strict mode
[    1.319507] vgaarb: loaded
[    1.320274] SCSI subsystem initialized
[    1.321075] usbcore: registered new interface driver usbfs
[    1.321177] usbcore: registered new interface driver hub
[    1.321253] usbcore: registered new device driver usb
[    1.322108] pps_core: LinuxPPS API ver. 1 registered
[    1.322135] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.322183] PTP clock support registered
[    1.322548] EDAC MC: Ver: 3.0.0
[    1.324162] FPGA manager framework
[    1.324411] Advanced Linux Sound Architecture Driver Initialized.
[    1.325479] NetLabel: Initializing
[    1.325504] NetLabel:  domain hash size = 128
[    1.325521] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    1.325671] NetLabel:  unlabeled traffic allowed by default
[    1.326902] clocksource: Switched to clocksource arch_sys_counter
[    1.406505] VFS: Disk quotas dquot_6.6.0
[    1.406652] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.407896] AppArmor: AppArmor Filesystem Enabled
[    1.408032] pnp: PnP ACPI: disabled
[    1.422689] NET: Registered PF_INET protocol family
[    1.423289] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    1.427774] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[    1.428159] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    1.429033] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[    1.429980] TCP: Hash tables configured (established 65536 bind 65536)
[    1.430230] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    1.430449] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    1.430873] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    1.430974] NET: Registered PF_XDP protocol family
[    1.431009] PCI: CLS 0 bytes, default 64
[    1.431452] Trying to unpack rootfs image as initramfs...
[    1.440200] hw perfevents: enabled with armv8_cortex_a55 PMU driver, 7 counters available
[    1.441007] kvm [1]: IPA Size Limit: 40 bits
[    1.441058] kvm [1]: GICv3: no GICV resource entry
[    1.441080] kvm [1]: disabling GICv2 emulation
[    1.441117] kvm [1]: GIC system register CPU interface enabled
[    1.441356] kvm [1]: vgic interrupt IRQ9
[    1.441670] kvm [1]: VHE mode initialized successfully
[    1.444968] Initialise system trusted keyrings
[    1.445063] Key type blacklist registered
[    1.445493] workingset: timestamp_bits=42 max_order=21 bucket_order=0
[    1.455201] zbud: lo
ersion 4.0 (2009/01/31) Phillip Lougher
[    1.462716] integrity: Platform Keyring initialized
[    1.514163] xor: measuring software checksum speed
[    1.520548]    8regs           :  1569 MB/sec
[    1.525569]    32regs          :  1985 MB/sec
[    1.532303]    arm64_neon      :  1480 MB/sec
[    1.532337] xor: using function: 32regs (1985 MB/sec)
[    1.532367] Key type asymmetric registered
[    1.532385] Asymmetric key parser 'x509' registered
[    1.532713] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[    1.533092] io scheduler mq-deadline registered
[    1.533122] io scheduler kyber registered
[    1.533481] io scheduler bfq registered
[    1.555172] EINJ: ACPI disabled.
[    1.564556] dma-pl330 fe530000.dmac: Loaded driver for PL330 DMAC-241330
[    1.564612] dma-pl330 fe530000.dmac:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    1.568249] dma-pl330 fe550000.dmac: Loaded driver for PL330 DMAC-241330
[    1.568306] dma-pl330 fe550000.dmac:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    1.581619] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
[    1.585868] fdd50000.serial: ttyS0 at MMIO 0xfdd50000 (irq = 23, base_baud = 1500000) is a 16550A
[    1.587919] fe650000.serial: ttyS1 at MMIO 0xfe650000 (irq = 41, base_baud = 1500000) is a 16550A
[    1.588217] serial serial0: tty port ttyS1 registered
[    1.589859] fe660000.serial: ttyS2 at MMIO 0xfe660000 (irq = 42, base_baud = 1500000) is a 16550A
[    1.702910] printk: console [ttyS2] enabled
[    1.705144] Serial: AMBA driver
[    1.709465] rockchip-vop2 fe040000.vop: Adding to iommu group 0
[    1.717113] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    1.732968] brd: module loaded
[    1.745352] loop: module loaded
[    1.747979] Loading iSCSI transport class v2.0-870.
[    1.749605] iscsi: registered transport (tcp)
[    1.750031] megasas: 07.719.03.00-rc1
[    1.759043] libphy: Fixed MDIO Bus: probed
[    1.762474] thunder_xcv, ver 1.0
[    1.762955] thunder_bgx, ver 1.0
[    1.763337] nicpf, ver 1.0
[    1.764910] hclge is initializing
[    1.765251] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
[    1.765907] hns3: Copyright (c) 2017 Huawei Corporation.
[    1.766523] igb: Intel(R) Gigabit Ethernet Network Driver
[    1.767052] igb: Copyright (c) 2007-2014 Intel Corporation.
[    1.767661] igbvf: Intel(R) Gigabit Virtual Function Network Driver
[    1.768230] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    1.769230] sky2: driver version 1.30
[    1.771737] VFIO - User Level meta-driver version: 0.3
[    1.775618] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.776258] ehci-pci: EHCI PCI platform driver
[    1.776744] ehci-platform: EHCI generic platform driver
[    1.779853] ehci-platform fd800000.usb: EHCI Host Controller
[    1.780423] ehci-platform fd800000.usb: new USB bus registered, assigned bus number 1
[    1.781343] ehci-platform fd800000.usb: irq 18, io mem 0xfd800000
[    1.795023] ehci-platform fd800000.usb: USB 2.0 started, EHCI 1.00
[    1.796079] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.16
[    1.796843] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.797498] usb usb1: Product: EHCI Host Controller
[    1.797943] usb usb1: Manufacturer: Linux 5.16.0-rc8-media ehci_hcd
[    1.798509] usb usb1: SerialNumber: fd800000.usb
[    1.799836] hub 1-0:1.0: USB hub found
[    1.800255] hub 1-0:1.0: 1 port detected
[    1.803727] ehci-platform fd880000.usb: EHCI Host Controller
[    1.804325] ehci-platform fd880000.usb: new USB bus registered, assigned bus number 2
[    1.805273] ehci-platform fd880000.usb: irq 20, io mem 0xfd880000
[    1.819008] ehci-platform fd880000.usb: USB 2.0 started, EHCI 1.00
[    1.820013] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.16
[    1.820778] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.821433] usb usb2: Product: EHCI Host Controller
[    1.821879] usb usb2: Manufacturer: Linux 5.16.0-rc8-media ehci_hcd
[    1.822444] usb usb2: SerialNumber: fd880000.usb
[    1.823778] hub 2-0:1.0: USB hub found
[    1.824214] hub 2-0:1.0: 1 port detected
[    1.825553] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.826155] ohci-pci: OHCI PCI platform driver
[    1.826679] ohci-platform: OHCI generic platform driver
[    1.827808] ohci-platform fd840000.usb: Generic Platform OHCI controller
[    1.828451] ohci-platform fd840000.usb: new USB bus registered, assigned bus number 3
[    1.829379] ohci-platform fd840000.usb: irq 19, io mem 0xfd840000
[    1.891304] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.16
[    1.892081] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.892739] usb usb3: Product: Generic Platform OHCI controller
[    1.893276] usb usb3: Manufacturer: Linux 5.16.0-rc8-media ohci_hcd
[    1.893841] usb usb3: SerialNumber: fd840000.usb
[    1.895147] hub 3-0:1.0: USB hub found
[    1.895587] hub 3-0:1.0: 1 portelatform fd8c0000.usb: Generic Platform OHCI controller
[    1.897636] ohci-platform fd8c0000.usb: new USB bus registered, assigned bus number 4
[    1.898557] ohci-platform fd8c0000.usb: irq 21, io mem 0xfd8c0000
[    1.963295] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.16
[    1.964074] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.964732] usb usb4: Product: Generic Platform OHCI controller
[    1.965268] usb usb4: Manufacturer: Linux 5.16.0-rc8-media ohci_hcd
[    1.965833] usb usb4: SerialNumber: fd8c0000.usb
[    1.967161] hub 4-0:1.0: USB hub found
[    1.967584] hub 4-0:1.0: 1 port detected
[    1.970292] usbcore: registered new interface driver usb-storage
[    1.974228] mousedev: PS/2 mouse device common for all mice
[    1.977208] i2c_dev: i2c /dev entries driver
[    1.980416] fan53555-regulator 0-001c: FAN53555 Option[12] Rev[15] Detected!
[    1.990220] Freeing initrd memory: 13704K
[    1.991801] rk808 0-0020: chip id: 0x8170
[    2.027237] random: fast init done
[    2.038005] rk808-regulator rk808-regulator: there is no dvs0 gpio
[    2.038609] rk808-regulator rk808-regulator: there is no dvs1 gpio
[    2.039235] rk808-regulator rk808-regulator: max buck steps per change: 8
[    2.055108] vcc_ddr: Bringing 500000uV into 1100000-1100000uV
[    2.085630] vccio_acodec: Bringing 1800000uV into 3300000-3300000uV
[    2.114349] vcc2v8_dvp: Bringing 1800000uV into 2800000-2800000uV
[    2.121994] boost: Bringing 4700000uV into 5000000-5000000uV
[    2.137553] input: rk805 pwrkey as /devices/platform/fdd40000.i2c/i2c-0/0-0020/rk805-pwrkey/input/input0
[    2.151239] rk808-rtc rk808-rtc: registered as rtc0
[    2.154438] rk808-rtc rk808-rtc: setting system clock to 2022-01-22T09:03:13 UTC (1642842193)
[    2.169419] sdhci: Secure Digital Host Controller Interface driver
[    2.170004] sdhci: Copyright(c) Pierre Ossman
[    2.171379] Synopsys Designware Multimedia Card Interface Driver
[    2.173955] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.177793] ledtrig-cpu: registered to indicate activity on CPUs
[    2.179646] SMCCC: SOC_ID: ARCH_FEATURES(ARCH_SOC_ID) returned error: fffffffffffffffd
[    2.180753] hid: raw HID events driver (C) Jiri Kosina
[    2.181705] usbcore: registered new interface driver usbhid
[    2.182217] usbhid: USB HID core driver
[    2.194564] NET: Registered PF_INET6 protocol family
[    2.247793] Segment Routing with IPv6
[    2.248221] In-situ OAM (IOAM) with IPv6
[    2.248707] NET: Registered PF_PACKET protocol family
[    2.249411] 8021q: 802.1Q VLAN Support v1.8
[    2.249880] Key type dns_resolver registered
[    2.251915] registered taskstats version 1
[    2.252315] Loading compiled-in X.509 certificates
[    2.257387] Loaded X.509 cert 'Build time autogenerated kernel key: 3490074eafa2d3b2c7b4d4c40b3f4b2753ecfa14'
[    2.262950] zswap: loaded using pool zstd/z3fold
[    2.264920] Key type ._fscrypt registered
[    2.265300] Key type .fscrypt registered
[    2.265659] Key type fscrypt-provisioning registered
[    2.269521] Btrfs loaded, crc32c=crc32c-generic, zoned=yes, fsverity=yes
[    2.270700] Key type encrypted registered
[    2.271143] AppArmor: AppArmor sha1 policy hashing enabled
[    2.271711] ima: No TPM chip found, activating TPM-bypass!
[    2.272242] ima: Allocated hash algorithm: sha1
[    2.272699] ima: No architecture policies found
[    2.273207] evm: Initialising EVM extended attributes:
[    2.273675] evm: security.selinux
[    2.273982] evm: security.SMACK64
[    2.274287] evm: security.SMACK64EXEC
[    2.274619] evm: security.SMACK64TRANSMUTE
[    2.275049] evm: security.SMACK64MMAP
[    2.275389] evm: security.apparmor
[    2.275701] evm: security.ima
[    2.275974] evm: security.capability
[    2.276300] evm: HMAC attrs: 0x1
[    2.367523] vop2_create_crtc: No remote for vp1
[    2.368000] vop2_create_crtc: No remote for vp2
[    2.368616] rockchip-drm display-subsystem: bound fe040000.vop (ops vop2_component_ops)
[    2.371253] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[    2.373056] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare HDMI I2C bus driver
[    2.376068] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops dw_hdmi_rockchip_ops)
[    2.377162] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[    2.378520] [drm] Initialized rockchip 1.0.0 20140818 for display-subsystem on minor 0
[    2.381749] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found
[    2.383376] rk_gmac-dwmac fe010000.ethernet: clock input or output? (input).
[    2.384033] rk_gmac-dwmac fe010000.ethernet: TX delay(0x30).
[    2.384552] rk_gmac-dwmac fe010000.ethernet: RX delay(0x10).
[    2.385079] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
[    2.385738] rk_gmac-dwmac fe010000.ethernet: clock input from PHY
[    2.391309] rk_gmac-dwmac fe010000.ethernet: init for RGMII
[    2.392182] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[    2.392844] rk_gmac-dwmac fe010000.ethernet:     DWMAC4/5
[    2.393317] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register supported
[    2.393992] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine supported
[    2.394665] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported
[    2.395338] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported
[    2.396019] rk_gmac-dwmac fe010000.ethernet: TSO supported
[    2.396523] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    2.397247] rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=8)
[    2.397887] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled
[    2.398431] rk_gmac-dwmac fe010000.ethernet: Using 32 bits DMA width
[    2.534929] libphy: stmmac: probed
[    2.554729] dwmmc_rockchip fe2b0000.mmc: IDMAC supports 32-bit address mode.
[    2.555462] dwmmc_rockchip fe2b0000.mmc: Using internal DMA controller.
[    2.556084] dwmmc_rockchip fe2b0000.mmc: Version ID is 270a
[    2.556115] printk: console [netcon0] enabled
[    2.556687] dwmmc_rockchip fe2b0000.mmc: DW MMC controller at irq 31,32 bit host data width,256 deep fifo
[    2.556994] netconsole: network logging started
[    2.558767] psci_checker: PSCI checker started using 4 CPUs
[    2.559057] dwmmc_rockchip fe2b0000.mmc: Got CD GPIO
[    2.559328] psci_checker: Starting hotplug tests
[    2.560161] psci_checker: Trying to turn off and on again all CPUs
[    2.561465] psci: CPU0 killed (polled 0 ms)
[    2.565379] psci: CPU1 killed (polled 0 ms)
[    2.569509] psci: CPU2 killed (polled 0 ms)
[    2.571554] mmc_host mmc0: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[    2.574687] Detected VIPT I-cache on CPU0
[    2.575118] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000
[    2.575821] CPU0: Booted secondary processor 0x0000000000 [0x412fd050]-cache on CPU1
[    2.579328] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000
[    2.580046] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[    2.583807] Detected VIPT I-cache on CPU2
[    2.584235] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000
[    2.584948] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[    2.587859] psci_checker: Trying to turn off and on again group 0 (CPUs 0-3)
[    2.589091] psci: CPU0 killed (polled 0 ms)
[    2.592598] psci: CPU1 killed (polled 0 ms)
[    2.595889] psci: CPU2 killed (polled 0 ms)
[    2.599281] Detected VIPT I-cache on CPU0
[    2.599711] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000
[    2.600412] CPU0: Booted secondary processor 0x0000000000 [0x412fd050]
[    2.603926] Detected VIPT I-cache on CPU1
[    2.604354] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000
[    2.605071] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[    2.608528] Detected VIPT I-cache on CPU2
[    2.608962] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000
[    2.609681] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[    2.612613] psci_checker: Hotplug tests passed OK
[    2.613058] psci_checker: Starting suspend tests (10 cycles per state)
[    2.613707] psci_checker: cpuidle not available on CPU 0, ignoring
[    2.614271] psci_checker: cpuidle not available on CPU 1, ignoring
[    2.614851] psci_checker: cpuidle not available on CPU 2, ignoring
[    2.615491] psci_checker: cpuidle not available on CPU 3, ignoring
[    2.616081] psci_checker: Could not start suspend tests on any CPU
[    2.616665] psci_checker: PSCI checker completed
[    2.617111] of_cfs_init
[    2.617388] of_cfs_init: OK
[    2.620790] ALSA device list:
[    2.621112]   No soundcards found.
[    2.624015] Freeing v  2.625157] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    2.626178] mmc0: new high speed SDHC card at address 0001
[    2.628204] mmcblk0: mmc0:0001 SD32G 29.1 GiB
[    2.635094] Run /init as init process
[    2.640413]  mmcblk0: p1
[    3.395104] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[    3.710976] mmc1: SDHCI controller on fe310000.mmc [fe310000.mmc] using ADMA
[    4.571366] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: data=writeback. Quota mode: none.
[    5.532143] systemd[1]: systemd 247.3-6 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
[    5.536895] systemd[1]: Detected architecture arm64.
[    5.563938] systemd[1]: Set hostname to <lenestol>.
[    5.763633] dw-apb-uart fe660000.serial: forbid DMA for kernel console
[    6.593597] systemd[1]: Queued start job for default target Graphical Interface.
[    6.596377] random: systemd: uninitialized urandom read (16 bytes read)
[    6.622004] systemd[1]: Created slice system-getty.slice.
[    6.623394] random: systemd: uninitialized urandom read (16 bytes read)
[    6.627809] systemd[1]: Created slice system-modprobe.slice.
[    6.628817] random: systemd: uninitialized urandom read (16 bytes read)
[    6.633472] systemd[1]: Created slice system-serial\x2dgetty.slice.
[    6.637669] systemd[1]: Created slice User and Session Slice.
[    6.638716] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[    6.640657] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    6.643317] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    6.644880] systemd[1]: Reached target Local Encrypted Volumes.
[    6.646109] systemd[1]: Reached target Paths.
[    6.647098] systemd[1]: Reached target Slices.
[    6.647946] systemd[1]: Reached target Swap.
[    6.648774] systemd[1]: Reached target System Time Set.
[    6.676088] systemd[1]: Listening on RPCbind Server Activation Socket.
[    6.678399] systemd[1]: Listening on Syslog Socket.
[    6.680473] systemd[1]: Listening on fsck to fsckd communication Socket.
[    6.681973] systemd[1]: Listening on initctl Compatibility Named Pipe.
[    6.684281] systemd[1]: Listening on Journal Audit Socket.
[    6.686138] systemd[1]: Listening on Journal Socket (/dev/log).
[    6.688502] systemd[1]: Listening on Journal Socket.
[    6.698585] systemd[1]: Listening on udev Control Socket.
[    6.700674] systemd[1]: Listening on udev Kernel Socket.
[    6.709728] systemd[1]: Mounting Huge Pages File System...
[    6.719956] systemd[1]: Mounting POSIX Message Queue File System...
[    6.729306] systemd[1]: Mounting RPC Pipe File System...
[    6.739578] systemd[1]: Mounting Kernel Debug File System...
[    6.749717] systemd[1]: Mounting Kernel Trace File System...
[    6.751775] systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped.
[    6.763580] systemd[1]: Starting Restore / save the current clock...
[    6.773803] systemd[1]: Starting Set the console keyboard layout...
[    6.784307] systemd[1]: Starting Create list of static device nodes for the current kernel...
[    6.797534] systemd[1]: Starting Load Kernel Module configfs...
[    6.807263] systemd[1]: Starting Load Kernel Module drm...
[    6.822737] systemd[1]: Starting Load Kernel Module fuse...
[    6.839584] systemd[1]: Started Nameserver information manager.
[    6.841862] systemd[1]: Reached target Network (Pre).
[    6.848164] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[    6.849341] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[    6.864694] systemd[1]: Starting Load Kernel Modules...
[    6.875533] systemd[1]: Starting Remount Root and Kernel File Systems...
[    6.889793] systemd[1]: Starting Coldplug All udev Devices...
[    6.912261] systemd[1]: Mounted Huge Pages File System.
[    6.914139] systemd[1]: Mounted POSIX Message Queue File System.
[    6.920296] systemd[1]: Mounted Kernel Debug File System.
[    6.922383] systemd[1]: Mounted Kernel Trace File System.
[    6.928399] systemd[1]: Finished Restore / save the current clock.
[    6.936899] fuse: init (API version 7.35)
[    6.938261] systemd[1]: Finished Create list of static device nodes for the current kernel.
[    6.942338] systemd[1]: modprobe@configfs.service: Succeeded.
[    6.945175] RPC: Registered named UNIX socket transport module.
[    6.945750] RPC: Registered udp transport module.
[    6.946095] systemd[1]: Finished Load Kernel Module configfs.
[    6.946181] RPC: Registered tcp transport module.
[    6.946188] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    6.956445] systemd[1]: modprobe@drm.service: Succeeded.
[    6.960149] systemd[1]: Finished Load Kernel Module drm.
[    6.983862] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,errors=remount-ro. Quota mode: none.
[    6.995565] systemd[1]: Mounted RPC Pipe File System.
[    6.999778] systemd[1]: modprobe@fuse.service: Succeeded.
[    7.002573] systemd[1]: Finished Load Kernel Module fuse.
[    7.010764] systemd[1]: Finished Load Kernel Modules.
[    7.015588] systemd[1]: Finished Remount Root and Kernel File Systems.
[    7.026249] systemd[1]: Mounting FUSE Control File System...
[    7.035659] systemd[1]: Mounting Kernel Configuration File System...
[    7.041823] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[    7.043209] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[    7.052727] systemd[1]: Starting Load/Save Random Seed...
[    7.062051] systemd[1]: Starting Apply Kernel Variables...
[    7.078717] systemd[1]: Starting Create System Users...
[    7.087922] systemd[1]: Mounted FUSE Control File System.
[    7.089791] systemd[1]: Mounted Kernel Configuration File System.


Armbian 22.02.0-trunk Bullseye ttyS2

lenestol login:
Here is the output of aplay -l
Code:
**** List of PLAYBACK Hardware Devices ****
card 0: HDMI [HDMI], device 0: fe400000.i2s-i2s-hifi i2s-hifi-0 [fe400000.i2s-i2s-hifi i2s-hifi-0]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 1: RK817 [Analog RK817], device 0: fe410000.i2s-rk817-hifi rk817-hifi-0 [fe410000.i2s-rk817-hifi rk817-hifi-0]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 2: SPDIF [SPDIF], device 0: fe460000.spdif-dit-hifi dit-hifi-0 [fe460000.spdif-dit-hifi dit-hifi-0]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
And the output of fdisk -l
Code:
Disk /dev/ram0: 4 MiB, 4194304 bytes, 8192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/ram1: 4 MiB, 4194304 bytes, 8192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/ram2: 4 MiB, 4194304 bytes, 8192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/ram3: 4 MiB, 4194304 bytes, 8192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/ram4: 4 MiB, 4194304 bytes, 8192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/ram5: 4 MiB, 4194304 bytes, 8192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/ram6: 4 MiB, 4194304 bytes, 8192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/ram7: 4 MiB, 4194304 bytes, 8192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/ram8: 4 MiB, 4194304 bytes, 8192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/ram9: 4 MiB, 4194304 bytes, 8192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/ram10: 4 MiB, 4194304 bytes, 8192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/ram11: 4 MiB, 4194304 bytes, 8192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/ram12: 4 MiB, 4194304 bytes, 8192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/ram13: 4 MiB, 4194304 bytes, 8192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/ram14: 4 MiB, 4194304 bytes, 8192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/ram15: 4 MiB, 4194304 bytes, 8192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/mmcblk0: 29.12 GiB, 31267487744 bytes, 61069312 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: CE161589-0136-441A-B356-7B3EA133A022

Device         Start      End  Sectors  Size Type
/dev/mmcblk0p1 32768 60456959 60424192 28.8G Linux filesystem


Disk /dev/zram0: 3.75 GiB, 4021952512 bytes, 981922 sectors
Units: sectors of 1 * 4096 = 4096 bytes
Sector size (logical/physical): 4096 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes


Disk /dev/zram1: 50 MiB, 52428800 bytes, 12800 sectors
Units: sectors of 1 * 4096 = 4096 bytes
Sector size (logical/physical): 4096 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
The only change I've made is to extlinux.conf to use the quartz device tree.
  Reply


Messages In This Thread
Armbian on Quartz64 - by dieselnutjob - 11-12-2021, 07:21 AM
RE: Armbian on Quartz64 - by dieselnutjob - 11-12-2021, 12:23 PM
RE: Armbian on Quartz64 - by TRS-80 - 11-12-2021, 02:16 PM
RE: Armbian on Quartz64 - by dieselnutjob - 11-12-2021, 03:41 PM
RE: Armbian on Quartz64 - by dieselnutjob - 11-14-2021, 09:58 AM
RE: Armbian on Quartz64 - by dieselnutjob - 11-15-2021, 08:21 AM
RE: Armbian on Quartz64 - by TRS-80 - 11-16-2021, 07:29 AM
RE: Armbian on Quartz64 - by dieselnutjob - 11-16-2021, 10:03 AM
RE: Armbian on Quartz64 - by TRS-80 - 11-16-2021, 02:24 PM
RE: Armbian on Quartz64 - by balbes150 - 11-22-2021, 01:25 AM
RE: Armbian on Quartz64 - by tllim - 01-23-2022, 10:32 PM
RE: Armbian on Quartz64 - by dieselnutjob - 11-22-2021, 03:53 AM
RE: Armbian on Quartz64 - by balbes150 - 11-22-2021, 05:30 AM
RE: Armbian on Quartz64 - by dieselnutjob - 11-22-2021, 05:54 AM
RE: Armbian on Quartz64 - by balbes150 - 01-13-2022, 05:25 AM
RE: Armbian on Quartz64 - by mulimoen - 01-21-2022, 03:12 PM
RE: Armbian on Quartz64 - by balbes150 - 01-22-2022, 02:31 AM
RE: Armbian on Quartz64 - by mulimoen - 01-22-2022, 03:23 AM
RE: Armbian on Quartz64 - by balbes150 - 01-23-2022, 06:30 AM
RE: Armbian on Quartz64 - by balbes150 - 01-22-2022, 06:51 AM
RE: Armbian on Quartz64 - by mulimoen - 01-23-2022, 10:54 AM
RE: Armbian on Quartz64 - by balbes150 - 01-24-2022, 03:46 AM
RE: Armbian on Quartz64 - by shaggy013 - 02-01-2022, 01:31 PM
RE: Armbian on Quartz64 - by balbes150 - 02-02-2022, 12:14 AM
RE: Armbian on Quartz64 - by shaggy013 - 02-13-2022, 04:09 AM
RE: Armbian on Quartz64 - by shaggy013 - 02-06-2022, 08:09 AM
RE: Armbian on Quartz64 - by dieselnutjob - 02-06-2022, 08:15 AM
RE: Armbian on Quartz64 - by shaggy013 - 02-06-2022, 02:39 PM
RE: Armbian on Quartz64 - by dieselnutjob - 02-06-2022, 04:48 PM
RE: Armbian on Quartz64 - by mulimoen - 02-13-2022, 04:43 AM
RE: Armbian on Quartz64 - by shaggy013 - 02-13-2022, 04:55 AM
RE: Armbian on Quartz64 - by mulimoen - 02-14-2022, 12:11 PM
RE: Armbian on Quartz64 - by balbes150 - 03-13-2022, 11:04 AM
RE: Armbian on Quartz64 - by tllim - 03-14-2022, 06:07 PM
RE: Armbian on Quartz64 - by balbes150 - 03-17-2022, 06:29 AM

Possibly Related Threads…
Thread Author Replies Views Last Post
  irradium (based on crux linux) Quartz64 riscv64, aarch64 mara 0 192 03-27-2024, 12:53 PM
Last Post: mara
  DietPi OS for Quartz64 MichaIng 45 10,847 12-12-2023, 02:26 AM
Last Post: sickos
  Armbian and LibreELEC and AltLinux for Quartz64 balbes150 147 59,399 11-17-2023, 08:21 AM
Last Post: balbes150
  slarm64 (unofficial slackware) Quartz64 RK3566 (aarch64) mara 56 41,259 10-17-2023, 10:55 AM
Last Post: mara
  quartz64-a - on-board SATA port problems manning 2 1,128 09-14-2023, 04:22 PM
Last Post: manning
  How the reset Quartz64-b onboard memory (emmc) beepy 2 828 07-20-2023, 10:44 PM
Last Post: beepy
  Armbian RAM issue JambonLeVrai 2 1,333 02-12-2023, 06:48 AM
Last Post: diederik
  crux-arm Quartz64 RK3566 (aarch64) mara 5 4,987 10-29-2022, 06:55 AM
Last Post: mara
  Ov5647 camera attached via csi to Quartz64 /Soquartz Randomuser 0 1,247 07-21-2022, 01:08 PM
Last Post: Randomuser

Forum Jump:


Users browsing this thread: 1 Guest(s)