Cap Error or Bad Memory
#1
Hi all for the past couple months I've been having some stability issues with my RockPro64 NAS. It would just seem to hang and require physical power cycle to get back online. About a week ago it seems to have given up the ghost.

This evening I hooked up an ftdi232 so I could look at the serial console as it attempts to boot, and I'm getting output similar to below pretty consistently, but with slight variations. I'm not so deep in the weeds with SBC init procedures to make too much sense of this, but "Cap error!" seems to indicate to me that there may be a faulty capacitor somewhere on my board, and the failure to read a given memory address seems to indicate that it may be a capacitor related to the ram chips. My question is, is there a good way for me to test and identify which if any capacitor may have gone bad so I can try to re-solder a new one on? If its the ram I'll resign myself to tossing the board as I don't have a reflow station, and the wife would kill me if I tried to use the oven to do that. I have a basic multimeter, and a cheapo oscilloscope from aliexpress if those tools may help drill into what I may need to replace here.

I'd really like to bring this little computer back to life if its not too much headache. This thing lasted me less than 2 years. For $80 I expected a lot better components and QC. I have an early 1st gen Raspberry Pi that's still chooching at 19 years old.

Code:
Version 1.19 20190305 In channel 0 CS = 0 MR0=0x98 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x0 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x98 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channel 1 training pass! change freq to 400MHz 0,1 channel 0 CS = 0 MR0=0x80 MR4=0x2 MR5=0x0 MR8=0x0 MR12=0x2 MR14=0x0 MR18=0x0 MR19=0x0 MR24=0x0 MR25=0x0 CS = 1 MR0=0x18 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x98 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channel 1 training pass! change freq to 800MHz 1,0 Channel 0: LPDDR4,800MHz W FF != R Cap error! Channel 1: LPDDR4,800MHz Col error!!! Cap error! ERR

Code:
Version 1.19 20190305 In channel 0 CS = 0 MR0=0x98 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x98 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channel 1 training pass! change freq to 400MHz 0,1 channel 0 CS = 0 MR0=0x98 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x98 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channel 1 training pass! change freq to 800MHz 1,0 Channel 0: LPDDR4,800MHz Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB Channel 1: LPDDR4,800MHz Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB 256B stride read addr 0x40008000 = 0x40010000 ERR

Code:
Version 1.19 20190305 In channel 0 CS = 0 MR0=0x98 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x0 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x98 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x0 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channel 1 training pass! change freq to 400MHz 0,1 channel 0 CS = 0 MR0=0x80 MR4=0x2 MR5=0x0 MR8=0x0 MR12=0x2 MR14=0x2 MR18=0x0 MR19=0x0 MR24=0x0 MR25=0x0 CS = 1 MR0=0x18 MR4=0x82 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x98 MR4=0x82 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channel 1 training pass! change freq to 800MHz 1,0 Channel 0: LPDDR4,800MHz W FF != R Cap error! Channel 1: LPDDR4,800MHz Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB no stride read addr 0x8000 = 0xFFFF8000 ERR

Code:
Version 1.19 20190305 In channel 0 CS = 0 MR0=0x98 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x0 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x98 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channel 1 training pass! change freq to 400MHz 0,1 channel 0 CS = 0 MR0=0x98 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x0 MR4=0x82 MR5=0x0 MR8=0x0 MR12=0x0 MR14=0x2 MR18=0x0 MR19=0x0 MR24=0x0 MR25=0x0 channel 1 CS = 0 MR0=0x98 MR4=0x82 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channel 1 training pass! change freq to 800MHz 1,0 Channel 0: LPDDR4,800MHz W FF != R Cap error! Channel 1: LPDDR4,800MHz Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB no stride ch 0 ddrconfig = 0x101, ddrsize = 0x2020 pmugrf_os_reg[2] = 0x2AA1E000, stride = 0x18 OUT U-Boot SPL board iq"Synchronous Abort" handler, esr 0x9600qSynchronous Abort" handler, esr 0x02000000ELR:    adac LR:      4308 x 0: 0000000000000030 x 1: 00000000000ELR:    adac LR:      4268 x 0: 0000000000000030 x 1: 00000000000"Synchronous Abort" handler, esr 0x96000"Synchronous Abort" handler, esr 0x02000000 "Synchronous Abort" handler, esr 0x96000""Synchronous Abort" handler, esr 0x86000000 ELR:    17ff0000531f3e00 LR:      3ecc x 0: 0000000"Synchronous Abort" handler, esr 0x02000000"Synchronous Abort" handler, esr 0x86000qSynchronous Abort" handler, esr 0x02000000 ELR:    8de0 LR:      4308 x 0: 0000000000000030 x 1: 0000000000000000 x 2: 00000000ff1a0014 x 3: 0000000000000030 x 4: 00000000003f9df8 x 5: 0000000000000000 x 6: 0000000000000001 x 7: 07f822e0003fb310 x 8: 00000000ff8c1edc x 9: 0000000000000000 x10: 0000000000000000 x11: 000000000000000c x12: 0000000080000000 x13: 000000000000000f x14: 00000qSynchronous Abort" handler, esr 0x02000000"Synchronous Abort" handler, esr 0x02000000"Synchronous Abort" handler, esr 0x02000000ELR:    adac LR:      3ecc x 0: 000000000000000a x 1: 0000000000000000 x 2: 0000000000003e00 x 3: 0000000000000030 x 4: 0000000000003e00 x 5: 0000000000000000 x 6: 0000000000000001 x 7: 000000000000000"Synchronous Abort" handler, esr 0x02000000 ELR:    adac LR:      4308 x 0: 0000000000000061 x 1: 0000000000""Synchronous Abort" handler, esr 0x0200000"Synchronous Abort" handler, esr 0x02000000ELR:    adac "Synchronous Abort" han"Synchronous Abort" handler, esr 0x02000000 "Synchronous Abort" handler, esr 0x0200qSynchronous Abort" handler, esr 0x02000000qSynchronous Abort" handler, esr 0x02000000"Synchronous Abort" handler, esr 0x02000000 "Synchronous Abort" handler, esr 0x02000000 "Synchronous Abort" handler, esr 0x02000000 "Synchronous Abort" handler, esr 0x02000000 "Synchronous Abort" handler, esr 0x02000000 "Synchronous Abort" handler, esr 0x02000000 "Synchronous Abort" handle"Synchronous Abort" handler, esr 0x02000000"Synchronous Abort" handler, esr 0x02000000"Synchronous Abort" handler, esr 0x02000000"
  Reply


Messages In This Thread
Cap Error or Bad Memory - by GuyNoIRQ - 03-22-2021, 08:18 PM
RE: Cap Error or Bad Memory - by tllim - 04-05-2021, 02:18 PM
RE: Cap Error or Bad Memory - by GuyNoIRQ - 04-05-2021, 02:28 PM
RE: Cap Error or Bad Memory - by nakato - 04-17-2021, 11:39 PM
RE: Cap Error or Bad Memory - by GuyNoIRQ - 04-20-2021, 01:56 PM
RE: Cap Error or Bad Memory - by t4_4t - 04-22-2021, 08:16 PM

Possibly Related Threads…
Thread Author Replies Views Last Post
  RockPro64 has bad Memory (Software sogfaults and kernel panics) kop316 20 40,951 08-04-2021, 07:42 PM
Last Post: t4_4t
  Industrial memory card m.ekstrom 1 4,898 03-23-2021, 05:55 AM
Last Post: barray

Forum Jump:


Users browsing this thread: 1 Guest(s)