Correct setup for u-boot and fstab ? Device not booting
#24
I have now tried the following combos:

ATF v2.3 + U-Boot 2020.10 --> does not boot at all
ATF v2.4 + U-Boot 2020.10 --> does boot, but can't parse extlinux.conf does boot but can't find eMMC
ATF v2.4 + U-Boot 2021.01 --> does boot, but can't parse extlinux.conf does boot but can't find eMMC

My Board is stamped PINE_H64_MODEL_B 2018-12-12.

Time to give up, for now, as I can't bring them up to life, especially with the new "SCP" Blob required by U-Boot. when building for the H6 which seems to have an additional OpenRisc Core as power management controller which makes things even more difficult.

Thanks to all for your time and help given, it is appreciated.

After checking the screenlogs again and again it dawned on me.... Idea

Reading up on extlinux and the examples given at linux-sunxi.org, I changed my extlinux.conf from

Code:
TIMEOUT 2 PROMPT 1 DEFAULT debian LABEL debian MENU LABEL Debian KERNEL /vmlinuz INITRD /initrd.img DEVICETREEDIR /dtbs APPEND console=tty1 root=LABEL=root rw rootwait

to

Code:
TIMEOUT 2 DEFAULT debian LABEL debian         MENU LABEL Debian         LINUX /vmlinuz         INITRD /initrd.img         FDT /dtbs/allwinner/sun50i-h6-pine-h64-model-b.dtb         APPEND console=tty1 root=LABEL=root rw rootwait

and now the board boots until u-boot tries to start the kernel, then it just stops.

Code:
U-Boot SPL 2020.10 (Mar 17 2021 - 14:12:11 +0000) DRAM: 2048 MiB Trying to boot from MMC2 NOTICE:  BL31: v2.4(release):v2.4 NOTICE:  BL31: Built : 13:48:42, Mar 17 2021 NOTICE:  BL31: Detected Allwinner H6 SoC (1728) NOTICE:  BL31: Found U-Boot DTB at 0xc086a30, model: Pine H64 NOTICE:  PSCI: System suspend is unavailable U-Boot 2020.10 (Mar 17 2021 - 14:12:11 +0000) Allwinner Technology CPU:   Allwinner H6 (SUN50I) Model: Pine H64 DRAM:  2 GiB MMC:   mmc@4020000: 0, mmc@4022000: 1 Loading Environment from FAT... Unable to use mmc 1:1... In:    serial@5000000 Out:   serial@5000000 Err:   serial@5000000 Net:   phy interface7 eth0: ethernet@5020000 starting USB... Bus usb@5101000: USB EHCI 1.00 Bus usb@5101400: USB OHCI 1.0 Bus usb@5311000: USB EHCI 1.00 Bus usb@5311400: USB OHCI 1.0 scanning bus usb@5101000 for devices... 1 USB Device(s) found scanning bus usb@5101400 for devices... 1 USB Device(s) found scanning bus usb@5311000 for devices... 1 USB Device(s) found scanning bus usb@5311400 for devices... 1 USB Device(s) found        scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot:  2  1  0 switch to partitions #0, OK mmc1(part 0) is current device Scanning mmc 1:1... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf 218 bytes read in 3 ms (70.3 KiB/s) 1: Debian Retrieving file: /initrd.img 28382050 bytes read in 2903 ms (9.3 MiB/s) Retrieving file: /vmlinuz 22722416 bytes read in 2342 ms (9.3 MiB/s) append: console=tty1 console=ttyS2,115200n8 root=LABEL=root rw rootwait Retrieving file: /dtbs/allwinner/sun50i-h6-pine-h64-model-b.dtb 32773 bytes read in 8 ms (3.9 MiB/s) Moving Image from 0x40080000 to 0x40200000, end=41840000 ## Flattened Device Tree blob at 4fa00000    Booting using the fdt blob at 0x4fa00000 EHCI failed to shut down host controller.    Loading Ramdisk to 484ee000, end 49fff362 ... OK    Loading Device Tree to 00000000484e2000, end 00000000484ed004 ... OK Starting kernel ...

I assume u-boot can't find the kernel to finish the process. Any ideas?
  Reply


Messages In This Thread
RE: Correct setup for u-boot and fstab ? Device not booting - by as365n4 - 03-17-2021, 08:37 AM

Possibly Related Threads…
Thread Author Replies Views Last Post
  U-boot not booting on H64 model B CGNZVV 2 7,885 06-08-2022, 10:32 AM
Last Post: as365n4
  Unable to boot any armbian linux vicsanca 6 14,296 10-17-2019, 12:08 PM
Last Post: JGwinner

Forum Jump:


Users browsing this thread: 1 Guest(s)