02-17-2021, 02:22 AM
Bonjour ...
Je rencontre in problème avec un carte PCIe qui bloque mon RockPro64 dès le lancement du noyau.
Voici ce que la console m'affiche :
... et l'affichage s'arrête là.
J'ai attendu plusieurs minutes mais rien de plus.
J'ai aussi testé un «ping» durant ce temps, au cas où ce ne soit qu'un problème de console :
La carte qui bloque le noyau au démarrage est celle-ci : Lorsque cette carte pcie n'est pas connectée, le noyau démarre sans aucun problème.
J'utilise maintenant le noyau ArmBian «5.10.16»,car avec le noyau «4.4.x», le problème était le même (voir pire).
Ayant aussi une carte «PCIE-EUX1-04 Ver.002» et ayant lu qu'elle était supportée par la carte RockPro64 : ... j'ai aussi testé cette carte mais cela ne fonctionne pas chez moi. Le résultat est le même.
Si quelqu'un aurait une piste ou une solution, je serai heureux qu'il me la transmette.
D'avance, Merci pour vos réponses.
Cordialement.
Hello ...
I run into a problem with a PCIe card that blocks my RockPro64 when the kernel is launched.
Here is what the console shows me :
... and the signage stops there.
I waited several minutes but nothing more.
I also tested a «ping» during this time, in case it is only a console problem :
The board that blocks the kernel at boot time is: When this pcie card is not connected, the kernel starts without any problems.
I now use the ArmBian kernel «5.10.16», because with the kernel «4.4.x», the problem was the same (see worse).
Having also a card «PCIE-EUX1-04 Ver.002» and having read that it was supported by the RockPro64 card : ... i also tested this card but it does not work for me. The result is the same.
If someone has a lead or a solution, I would be happy to hear from them.
In advance, thank you for your answers.
Best Regards.
Je rencontre in problème avec un carte PCIe qui bloque mon RockPro64 dès le lancement du noyau.
Voici ce que la console m'affiche :
Code:
U-Boot 2020.10-armbian (Feb 04 2021 - 02:11:12 +0100)
SoC: Rockchip rk3399
Reset cause: POR
Model: Pine64 RockPro64 v2.1
DRAM: 3.9 GiB
PMIC: RK808
MMC: mmc@fe310000: 2, mmc@fe320000: 1, sdhci@fe330000: 0
Loading Environment from SPIFlash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Model: Pine64 RockPro64 v2.1
Net: eth0: ethernet@fe300000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found U-Boot script /boot/boot.scr
3185 bytes read in 5 ms (622.1 KiB/s)
## Executing script at 00500000
Boot script loaded from mmc 1
213 bytes read in 4 ms (51.8 KiB/s)
13102297 bytes read in 558 ms (22.4 MiB/s)
28582400 bytes read in 1214 ms (22.5 MiB/s)
75846 bytes read in 13 ms (5.6 MiB/s)
267 bytes read in 8 ms (32.2 KiB/s)
Applying kernel provided DT overlay rockchip-pcie-gen2.dtbo
2698 bytes read in 9 ms (292 KiB/s)
Applying kernel provided DT fixup script (rockchip-fixup.scr)
## Executing script at 09000000
Moving Image from 0x2080000 to 0x2200000, end=3de0000
## Loading init Ramdisk from Legacy Image at 06000000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 13102233 Bytes = 12.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01f00000
Booting using the fdt blob at 0x1f00000
Loading Ramdisk to f1291000, end f1f0fc99 ... OK
Loading Device Tree to 00000000f1216000, end 00000000f1290fff ... OK
Starting kernel ...J'ai attendu plusieurs minutes mais rien de plus.
J'ai aussi testé un «ping» durant ce temps, au cas où ce ne soit qu'un problème de console :
Code:
...
From xxx.xxx.xxx.xxx icmp_seq=3493 Destination Host Unreachable
From xxx.xxx.xxx.xxx icmp_seq=3494 Destination Host Unreachable
From xxx.xxx.xxx.xxx icmp_seq=3495 Destination Host Unreachable
From xxx.xxx.xxx.xxx icmp_seq=3496 Destination Host Unreachable
From xxx.xxx.xxx.xxx icmp_seq=3500 Destination Host Unreachable
From xxx.xxx.xxx.xxx icmp_seq=3503 Destination Host Unreachable
...La carte qui bloque le noyau au démarrage est celle-ci : Lorsque cette carte pcie n'est pas connectée, le noyau démarre sans aucun problème.
J'utilise maintenant le noyau ArmBian «5.10.16»,car avec le noyau «4.4.x», le problème était le même (voir pire).
Ayant aussi une carte «PCIE-EUX1-04 Ver.002» et ayant lu qu'elle était supportée par la carte RockPro64 : ... j'ai aussi testé cette carte mais cela ne fonctionne pas chez moi. Le résultat est le même.
Si quelqu'un aurait une piste ou une solution, je serai heureux qu'il me la transmette.
D'avance, Merci pour vos réponses.
Cordialement.
Hello ...
I run into a problem with a PCIe card that blocks my RockPro64 when the kernel is launched.
Here is what the console shows me :
Code:
U-Boot 2020.10-armbian (Feb 04 2021 - 02:11:12 +0100)
SoC: Rockchip rk3399
Reset cause: POR
Model: Pine64 RockPro64 v2.1
DRAM: 3.9 GiB
PMIC: RK808
MMC: mmc@fe310000: 2, mmc@fe320000: 1, sdhci@fe330000: 0
Loading Environment from SPIFlash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Model: Pine64 RockPro64 v2.1
Net: eth0: ethernet@fe300000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found U-Boot script /boot/boot.scr
3185 bytes read in 5 ms (622.1 KiB/s)
## Executing script at 00500000
Boot script loaded from mmc 1
213 bytes read in 4 ms (51.8 KiB/s)
13102297 bytes read in 558 ms (22.4 MiB/s)
28582400 bytes read in 1214 ms (22.5 MiB/s)
75846 bytes read in 13 ms (5.6 MiB/s)
267 bytes read in 8 ms (32.2 KiB/s)
Applying kernel provided DT overlay rockchip-pcie-gen2.dtbo
2698 bytes read in 9 ms (292 KiB/s)
Applying kernel provided DT fixup script (rockchip-fixup.scr)
## Executing script at 09000000
Moving Image from 0x2080000 to 0x2200000, end=3de0000
## Loading init Ramdisk from Legacy Image at 06000000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 13102233 Bytes = 12.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01f00000
Booting using the fdt blob at 0x1f00000
Loading Ramdisk to f1291000, end f1f0fc99 ... OK
Loading Device Tree to 00000000f1216000, end 00000000f1290fff ... OK
Starting kernel ...I waited several minutes but nothing more.
I also tested a «ping» during this time, in case it is only a console problem :
Code:
...
From xxx.xxx.xxx.xxx icmp_seq=3493 Destination Host Unreachable
From xxx.xxx.xxx.xxx icmp_seq=3494 Destination Host Unreachable
From xxx.xxx.xxx.xxx icmp_seq=3495 Destination Host Unreachable
From xxx.xxx.xxx.xxx icmp_seq=3496 Destination Host Unreachable
From xxx.xxx.xxx.xxx icmp_seq=3500 Destination Host Unreachable
From xxx.xxx.xxx.xxx icmp_seq=3503 Destination Host Unreachable
...The board that blocks the kernel at boot time is: When this pcie card is not connected, the kernel starts without any problems.
I now use the ArmBian kernel «5.10.16», because with the kernel «4.4.x», the problem was the same (see worse).
Having also a card «PCIE-EUX1-04 Ver.002» and having read that it was supported by the RockPro64 card : ... i also tested this card but it does not work for me. The result is the same.
If someone has a lead or a solution, I would be happy to hear from them.
In advance, thank you for your answers.
Best Regards.