(06-26-2017, 06:06 AM)xalius Wrote: Do you have a serial adapter to see what the boot console says? Any USB/serial dongle with 3.3V I/O will do....
Just found the PMPROG01 I bought with the Pine...
I get this with the LCD connected... at the end the power light goes out.
Code:
[ 0.0]HELLO! BOOT0 is starting!
[ 0.3]boot0 commit : 267600f3b448b722fb13c6de3199a2c040816b6d
[ 0.10]boot0 version : 4.0
[ 0.14]rsb_send_initseq: rsb clk 400Khz -> 3Mhz
[ 0.20]PMU: AXP81X
[ 0.23]set pll start
[ 0.29]set pll end
[ 0.31]DRAM driver version: V1.2
[ 0.34]the chip id is 0x000000ba
[ 0.38]the chip id is 0x000000ba
[ 0.41]the chip id is 0x000000ba
[ 0.45]the chip id is 0x000000ba
[ 0.48]the chip id is 0x000000ba
[ 0.52]start ddr type auto scan mode
[ 0.58]DRAM DQS gate training error
[ 0.62]DRAM init error!
[ 0.67]DRAM DQS gate training error
[ 0.71]DRAM init error!
[ 0.76]DRAM init OK
[ 0.78]ddr3 try success
[ 0.81]DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
[ 0.87]DRAM clk = 672 MHz
[ 0.89]DRAM zq value: 003b3bbb
[ 0.95]DRAM single rank full DQ OK
[ 0.99]DRAM size = 2048 MB
[ 0.102]DRAM init ok
[ 0.105]dram size =2048
[ 0.109]card no is 0
[ 0.111]sdcard 0 line count 4
[ 0.114][mmc]: mmc driver ver 2016-03-15 16:30
[ 0.119][mmc]: sdc0 spd mode error, 2
[ 0.132][mmc]: Wrong media type 0x00000000
[ 0.136][mmc]: ***Try SD card 0***
[ 0.152][mmc]: HSSDR52/SDR25 4 bit
[ 0.156][mmc]: 50000000 Hz
[ 0.159][mmc]: 60906 MB
[ 0.161][mmc]: ***SD/MMC 0 init OK!!!***
[ 0.268]Succeed in loading uboot from sdmmc flash.
[ 0.273]Entry_name = u-boot
[ 0.282]Entry_name = monitor
[ 0.286]Entry_name = scp
[ 0.294]set arisc reset to de-assert state
[ 0.298]Entry_name = logo
[ 0.302]Entry_name = shutdowncharge
[ 0.306]Entry_name = androidcharge
[ 0.311]Ready to disable icache.
[ 0.321]cpu1 delay 20000
▒9=▒ Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):4d7c48e
NOTICE: BL3-1: Built : 17:07:29, May 9 2016
NOTICE: BL3-1 commit: 4d7c48ec3b1cfec7664dc9ffd3b6663074cec4b3
[SCP] :sunxi-arisc driver begin startup 2
[SCP] :hwspinlock:0x1c18000
[SCP] :msgbox:0x1c17000
[SCP] :message manager initialize start:0x48105000, size:0x1000
[SCP] :sunxi-arisc driver v1.10 is starting
INFO: BL3-1: Initializing runtime services
ERROR: Error initializing runtime service tspd_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x4a000000
INFO: BL3-1: Next image spsr = 0x1d3
U-Boot 2014.07 (Feb 08 2017 - 10:33:23) Allwinner Technology
uboot commit : 13dcbb66e9d12eea804ab8a35e29ecdb3025967c
normal mode: with secure monitor
rsb_send_initseq: rsb clk 400Khz -> 3Mhz
[ 0.399]pmbus: ready
[SCP] :wait arisc ready....
[SCP] :arisc version: [sun8iw5_v0.03.00-227-gcec3a2b]
[SCP] :sunxi-arisc driver v1.10 startup ok
pmu type = 0x11
[ 0.418]PMU: AXP81X
[ 0.418]PMU: read AXP81X 84H=0xf2
[ 0.420]PMU: write AXP81X 84H=0xf6
[ 0.423]PMU: AXP81X found
factory
axp end
run key detect
no key found
no uart input
DRAM: 2 GiB
fdt addr0: 0xb6e78db8
fdt addr1: 0xb6e8b618
Relocation Offset is: 75ede000
In: serial
Out: serial
Err: serial
gic: sec monitor mode
[ 0.519]flash init start
workmode = 0,storage type = 1
[ 0.524]MMC: 0
[ 0.526]mmc init start to delay
[ 1.031]mmc init end to delay
[mmc]: mmc driver ver 2016-03-31 15:50:00
SUNXI SD/MMC: 0
[mmc]: 50 MHz...
[mmc]: sample: 53 - 188(ps)
[mmc]: 100 MHz...
[mmc]: sample: 27 - 185(ps)
[mmc]: 200 MHz...
[mmc]: sample: 13 - 192(ps)
[mmc]: media type 0x0
[mmc]: Wrong media type 0x0
[mmc]: ************Try SD card 0************
[mmc]: host caps: 0x27
[mmc]: MID 03 PSN b0d00ce3
[mmc]: PNM SE64G -- 0x53-45-36-34-47
[mmc]: PRV 8.0
[mmc]: MDT m-4 y-2015
[mmc]: speed mode : HSSDR52/SDR25
[mmc]: clock : 50000000 Hz
[mmc]: bus_width : 4 bit
[mmc]: user capacity : 60906 MB
[mmc]: ************SD/MMC 0 init OK!!!************
[mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte
[mmc]: secure_feature : 0x0
[mmc]: secure_removal_type : 0x0
[ 1.188]sunxi flash init ok
sunxi_partition_init
mbr part count = 15
[ 1.194]flash init end
[cpu1]secondary entry
[ 1.197]power on secondary cpu
set power on vol to default
try to burn key
[cpu1]dcdc1_vol = 3300, onoff=1
read item0 copy0
[cpu1]dcdc6_vol = 1100, onoff=1
Item0 (Map) magic is bad
[cpu1]aldo1_vol = 2800, onoff=0
the secure storage item0 copy0 is bad
[cpu1]aldo2_vol = 1800, onoff=1
read item0 copy1
[cpu1]aldo3_vol = 3000, onoff=1
Item0 (Map) magic is bad
[cpu1]dldo1_vol = 3300, onoff=0
the secure storage item0 copy0 == copy1, the data is good
[cpu1]dldo2_vol = 3300, onoff=0
the secure storage map is empty
[cpu1]dldo3_vol = 2800, onoff=0
no item name key_burned_flag in the map
[cpu1]dldo4_vol = 3300, onoff=1
sunxi secure storage has no flag
[cpu1]eldo1_vol = 1800, onoff=1
[ 1.257]usb burn from boot
[cpu1]eldo2_vol = 1800, onoff=0
wait cpu1 down
[cpu1]eldo3_vol = 1800, onoff=0
[cpu1]fldo1_vol = 1200, onoff=0
[cpu1]fldo2_vol = 1100, onoff=1
[cpu1]gpio0_vol = 3100, onoff=0
[cpu1]find power_sply to end
[cpu1]dcin exist
[cpu1]no battery exist
[cpu1]on cpu2
[cpu1]on end
[cpu2]third entry
[ 1.287]initr_sunxi_display start
[cpu1]drv_disp_init
[cpu2]bmp file buffer: 0x47400000, bmp_info.buffer: 46400000
[cpu2]kill cpu 2
[cpu1]init_clocks: finish init_clocks.
[cpu1]fail to get clk for lcd1
[cpu1]fail to get clk for lcd1
[cpu1]clk_set parent tcon1 fail
[cpu1]clk_set parent pll_mipi fail
[cpu1]pwm_request:pwm number = 1
[cpu1]pwm_request: reg = 0x1f03800. pwm = 16.
[cpu1]request pwm success, pwm = 16.
[cpu1]enable power vcc-hdmi-33, ret=0
[cpu1]drv_disp_init finish
[cpu1]reading hdmi.txt
[cpu1]FAT: Misaligned buffer address (b6e6ac3c)
[cpu1]4 bytes read in 3 ms ([cpu1]1000 Bytes/s)
[cpu1]Hekang read hdmi_mode = 5
[cpu1]boot_disp.output_disp=0
[cpu1]boot_disp.output_type=1
[cpu1]boot_disp.output_mode=4
[cpu1]fetch script data boot_disp.auto_hpd fail
[cpu1]disp0 device type(1) enable
[cpu1]enable power vcc-dsi-33, ret=0
[