PINE64   ›   ROCK64   ›   Rock64 Hardware and Accessories   ›   Recovery button

Recovery button
stephen fleming
Pine Adept
***
Joined: Jan 2016
Posts: 72

Reputation: 0
#1
07-04-2017, 03:14 AM
Another question about something on the board. What does the recovery button do?
  Reply
fire219
Community Platforms Sysadmin
*******
Administrators
Joined: Jan 2016
Posts: 351

Reputation: 119
#2
07-04-2017, 11:55 AM
When used properly, it puts the board into Loader Mode, which is a special mode in the bootloader which allows data to be written/read directly from the eMMC chip, over a USB cable to a computer.

But while the board is running an OS, it should not do anything.
Community administrator and sysadmin for PINE64
(Translation: If something breaks on the website, forum, or chat network, I'm a good person to yell at about it)

  Reply
PDXpi
Pine Initiate
**
Joined: Apr 2019
Posts: 18

Reputation: 2
#3
01-24-2021, 06:00 PM
(07-04-2017, 11:55 AM)fire219 Wrote: When used properly, it puts the board into Loader Mode, which is a special mode in the bootloader which allows data to be written/read directly from the eMMC chip, over a USB cable to a computer.
 
  1. The OTG port of the Rock64 is a USB Type A Female socket.
  2. All of the USB ports on my desktop systems USB Type A Female sockets.
So what kind of cable would you use to connect the Rock64 to the other computer (i.e., any of my desktop systems)?

TIA!
Eric P.
Portland, Oregon
  Reply
fire219
Community Platforms Sysadmin
*******
Administrators
Joined: Jan 2016
Posts: 351

Reputation: 119
#4
01-25-2021, 08:58 AM
(01-24-2021, 06:00 PM)PDXpi Wrote:
(07-04-2017, 11:55 AM)fire219 Wrote: When used properly, it puts the board into Loader Mode, which is a special mode in the bootloader which allows data to be written/read directly from the eMMC chip, over a USB cable to a computer.
 
  1. The OTG port of the Rock64 is a USB Type A Female socket.
  2. All of the USB ports on my desktop systems USB Type A Female sockets.
So what kind of cable would you use to connect the Rock64 to the other computer (i.e., any of my desktop systems)?

TIA!

You are correct in your observations. Wink 

You need a USB Type A Male-Male cable. Then you can flash the eMMC with a utility like rkflashtool.
Community administrator and sysadmin for PINE64
(Translation: If something breaks on the website, forum, or chat network, I'm a good person to yell at about it)

  Reply
PDXpi
Pine Initiate
**
Joined: Apr 2019
Posts: 18

Reputation: 2
#5
01-25-2021, 08:10 PM
Thanks, Fire219 - Using your description (i.e., "USB Type A Male-Male") I was able to find a variety of cables for this task!

(I'd been searching for "USB Type A OTG". And that wasn't finding the male-male cables.)

I'm really looking forward to being able to flash the eMMC card now without having to open the case!
Eric P.
Portland, Oregon
  Reply
PDXpi
Pine Initiate
**
Joined: Apr 2019
Posts: 18

Reputation: 2
#6
01-26-2021, 12:33 PM
(01-25-2021, 08:10 PM)PDXpi Wrote: I'm really looking forward to being able to flash the eMMC card now without having to open the case!

But the Recovery Button is inside the case. And there's no way to access it without having to open the case. Exclamation

Ug!  It would have been good if the Recovery Button were accessible from the outside - The same way the the Power Button and the Reset Button are!

Thanks, anyhow!
Eric P.
Portland, Oregon
  Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  3D-Printable Button Pegs for the ROCK64 Aluminium Case CounterPillow 2 4,164 08-04-2022, 01:31 AM
Last Post: Vicky Weimann PhD
  Attaching a physical button to the ROCK64 momoster69 1 4,472 03-03-2019, 09:15 AM
Last Post: dkryder
  Extending power / reset button nmhart322 5 8,145 12-16-2017, 07:57 PM
Last Post: dkryder

Forum Jump:


Users browsing this thread: 1 Guest(s)