02-04-2016, 05:15 PM
(02-04-2016, 08:22 AM)Hahaburger Wrote: Weird, I almost changed nothing on that image. I've just added one kernel parameter and some sepolicies.
I also checked your sha256sum which is the same on my PC so download is OK.
I've prepared new boot image and changed kernel parameter:
https://drive.google.com/file/d/0B5NrIPX...sp=sharing
Trying again and writing down the steps (in order to catch any mistake).
1.
android_20160112.img (SHA256: c734b943a5f537b5bff7fbe9792ceb63e13f8258037d6082e5c570272f6b74e9)
Code:
sudo dd if=android_20160112.img of=/dev/sdc bs=16M2.
boot.img (SHA256: 09bca0dde761b230417d33137b5ba9ebcd83c27ead2f3a250b9d6d7ce49ffc2d)
system.img (SHA256: 392320bbaae74af650e71c65ce62b737b3cfee193316204633889515be770134)
Code:
sudo dd if=boot.img of=/dev/sdc6 bs=16M
sudo dd if=system.img of=/dev/sdc7 bs=16M Then, booted. Here is the log:
Code:
Connected.
HELLO! BOOT0 is starting!
boot0 commit : 2fe7b0a9fb512fae2996ec1a2ba89d535e1f3c4d
boot0 version : 4.0.0
set pll start
set pll end
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
DRAM driver version: V1.1
rsb_send_initseq: rsb clk 400Khz -> 3Mhz
PMU: AXP81X
ddr voltage = 1500 mv
DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM clk = 672 MHz
DRAM zq value: 003b3bbb
DRAM single rank full DQ OK
DRAM size = 1024 MB
DRAM init ok
dram size =1024
card boot number = 0, boot0 copy = 0
card no is 0
sdcard 0 line count 4
[mmc]: mmc driver ver 2015-05-08 20:06
[mmc]: sdc0 spd mode error, 2
[mmc]: Wrong media type 0x00000000
[mmc]: ***Try SD card 0***
[mmc]: HSSDR52/SDR25 4 bit
[mmc]: 50000000 Hz
[mmc]: 15423 MB
[mmc]: ***SD/MMC 0 init OK!!!***
sdcard 0 init ok
The size of uboot is 000fc000.
sum=15bc131f
src_sum=15bc131f
Succeed in loading uboot from sdmmc flash.
boot0: start load other image
boot0: Loading BL3-1
Loading file 0 at address 0x40000000,size 0x0000b400 success
boot0: Loading scp
Loading file 2 at address 0x00040000,size 0x00019c00 success
set arisc reset to de-assert state
Ready to disable icache.
K9=� Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):2fe7b0a
NOTICE: BL3-1: Built : 10:15:37, Jan 12 2016
NOTICE: BL3-1 commit: 2fe7b0a9fb512fae2996ec1a2ba89d535e1f3c4d
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x4a000000
INFO: BL3-1: Next image spsr = 0x1d3
U-Boot 2014.07 (Jan 12 2016 - 10:15:41) Allwinner Technology
uboot commit : 2fe7b0a9fb512fae2996ec1a2ba89d535e1f3c4d
rsb: secure monitor exist
[ 0.377]pmbus: ready
[ 0.380][ARISC] :arisc initialize
[ 0.710][ARISC] :arisc_dvfs_cfg_vf_table: support only one vf_table
[SCP] :sunxi-arisc driver begin startup 2
[SCP] :arisc_para size:1a8
[SCP] :arisc version: [v0.1.76]
[SCP] :sunxi-arisc driver v1.10 is starting
[ 0.838][ARISC] :sunxi-arisc driver startup succeeded
[ 0.871]PMU: AXP81X
[ 0.873]PMU: read AXP81X 84H=0xf2
[ 0.877]PMU: write AXP81X 84H=0xf6
[ 0.880]PMU: AXP81X found
bat_vol=337, ratio=100
[ 0.887]PMU: dcdc2 1100
[ 0.890]PMU: cpux 1008 Mhz,AXI=336 Mhz
PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz AHB2=300Mhz MBus=400Mhz
device_type = 3253, onoff=1
dcdc1_vol = 3300, onoff=1
dcdc2_vol = 1100, onoff=1
dcdc6_vol = 1100, onoff=1
aldo1_vol = 2800, onoff=0
aldo2_vol = 1800, onoff=1
aldo3_vol = 3000, onoff=1
dldo1_vol = 3300, onoff=0
dldo2_vol = 3300, onoff=0
dldo3_vol = 2800, onoff=0
dldo4_vol = 3300, onoff=1
eldo1_vol = 1800, onoff=1
eldo2_vol = 1800, onoff=0
eldo3_vol = 1800, onoff=0
fldo1_vol = 1200, onoff=0
fldo2_vol = 1100, onoff=1
gpio0_vol = 3100, onoff=0
vbus not exist
no battery, limit to dc
run key detect
key pressed value=0x1
key pressed value=0x1
fel key not configed
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x3
key pressed value=0x2
key pressed value=0x2
key pressed value=0x2
key pressed value=0x3
key pressed value=0x2
key pressed value=0x2
key pressed value=0x3
key pressed value=0x2
key pressed value=0x2
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
key pressed value=0x3
time out
key not pressed anymore
no uart input
DRAM: 1008 MiB
fdt addr: 0x76eb70e0
Relocation Offset is: 35f09000
In: serial
Out: serial
Err: serial
gic: sec monitor mode
[ 12.573]start
drv_disp_init
init_clocks: finish init_clocks.
enable power vcc-hdmi-33, ret=0
drv_disp_init finish
boot_disp.output_disp=0
boot_disp.output_type=3
boot_disp.output_type=10
fetch script data boot_disp.auto_hpd fail
disp0 device type(4) enable
attched ok, mgr0<-->device1, type=4, mode=10
[ 12.945]end
workmode = 0,storage type = 1
[ 12.949]MMC: 0
[mmc]: mmc driver ver 2015-07-29 14:10:00
SUNXI SD/MMC: 0
[mmc]: start mmc_calibrate_delay_unit, don't access device...
[mmc]: delay chain cal done, sample: 200(ps)
[mmc]: media type 0x0
[mmc]: Wrong media type 0x0
[mmc]: ************Try SD card 0************
[mmc]: host caps: 0x27
[mmc]: MID 1b PSN 008541f6
[mmc]: PNM 00000 -- 0x30-30-30-30-30
[mmc]: PRV 1.0
[mmc]: MDT m-12 y-2011
[mmc]: speed mode : HSSDR52/SDR25
[mmc]: clock : 50000000 Hz
[mmc]: bus_width : 4 bit
[mmc]: user capacity : 15423 MB
[mmc]: ************SD/MMC 0 init OK!!!************
[mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte
[mmc]: secure_feature : 0x0
[mmc]: secure_removal_type : 0x0
[ 13.160]sunxi flash init ok
--------fastboot partitions--------
-total partitions:11-
-name- -start- -size-
bootloader : 1000000 2000000
env : 3000000 1000000
boot : 4000000 1000000
system : 5000000 60000000
misc : 65000000 1000000
recovery : 66000000 2000000
cache : 68000000 30000000
metadata : 98000000 1000000
private : 99000000 1000000
alog : 9a000000 5000000
UDISK : 9f000000 0
-----------------------------------
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_mmc
key 1
recovery key high 12, low 10
fastboot key high 6, low 4
misc partition found
to be run cmd=run setargs_mmc boot_normal
update dtb dram start
update dtb dram end
** Unrecognized filesystem type **
load file(sn.txt) error
serial is: 241051900808142809cb
no battery exist
sunxi_bmp_logo_display
reading bootlogo.bmp
681774 bytes read in 36 ms (18.1 MiB/s)
bmp file buffer: 0x41000000, bmp_info.buffer: 47400000
fetch script data boot_disp.output_full fail
screen_id =0, screen_width =1920, screen_height =1080
frame buffer address 47400036
[ 13.769]inter uboot shell
Hit any key to stop autoboot: 0
read partition: boot or recovery
[ 14.602]sunxi flash read :offset 4000000, 16918757 bytes OK
Kernel load addr 0x41080000 size 10881 KiB
Kernel command line: enforcing=0
RAM disk load addr 0x42000000 size 4617 KiB
[ 14.946]ready to boot
prepare for kernel
[mmc]: MMC Device 2 not found
[mmc]: mmc 2 not find, so not exit
Starting kernel ...
INFO: BL3-1: Next image address = 0x41080000
INFO: BL3-1: Next image spsr = 0x3c5Which means it got stuck.
I then tried out an earlier boot.img
and here is the full log
Code:
Connected.
HELLO! BOOT0 is starting!
boot0 commit : 2fe7b0a9fb512fae2996ec1a2ba89d535e1f3c4d
boot0 version : 4.0.0
set pll start
set pll end
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
DRAM driver version: V1.1
rsb_send_initseq: rsb clk 400Khz -> 3Mhz
PMU: AXP81X
ddr voltage = 1500 mv
DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM clk = 672 MHz
DRAM zq value: 003b3bbb
DRAM single rank full DQ OK
DRAM size = 1024 MB
DRAM init ok
dram size =1024
card boot number = 0, boot0 copy = 0
card no is 0
sdcard 0 line count 4
[mmc]: mmc driver ver 2015-05-08 20:06
[mmc]: sdc0 spd mode error, 2
[mmc]: Wrong media type 0x00000000
[mmc]: ***Try SD card 0***
[mmc]: HSSDR52/SDR25 4 bit
[mmc]: 50000000 Hz
[mmc]: 15423 MB
[mmc]: ***SD/MMC 0 init OK!!!***
sdcard 0 init ok
The size of uboot is 000fc000.
sum=15bc131f
src_sum=15bc131f
Succeed in loading uboot from sdmmc flash.
boot0: start load other image
boot0: Loading BL3-1
Loading file 0 at address 0x40000000,size 0x0000b400 success
boot0: Loading scp
Loading file 2 at address 0x00040000,size 0x00019c00 success
set arisc reset to de-assert state
Ready to disable icache.
K9=� Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):2fe7b0a
NOTICE: BL3-1: Built : 10:15:37, Jan 12 2016
NOTICE: BL3-1 commit: 2fe7b0a9fb512fae2996ec1a2ba89d535e1f3c4d
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x4a000000
INFO: BL3-1: Next image spsr = 0x1d3
U-Boot 2014.07 (Jan 12 2016 - 10:15:41) Allwinner Technology
uboot commit : 2fe7b0a9fb512fae2996ec1a2ba89d535e1f3c4d
rsb: secure monitor exist
[ 0.376]pmbus: ready
[ 0.379][ARISC] :arisc initialize
[ 0.710][ARISC] :arisc_dvfs_cfg_vf_table: support only one vf_table
[SCP] :sunxi-arisc driver begin startup 2
[SCP] :arisc_para size:1a8
[SCP] :arisc version: [v0.1.76]
[SCP] :sunxi-arisc driver v1.10 is starting
[ 0.838][ARISC] :sunxi-arisc driver startup succeeded
[ 0.871]PMU: AXP81X
[ 0.873]PMU: read AXP81X 84H=0xf2
[ 0.877]PMU: write AXP81X 84H=0xf6
[ 0.880]PMU: AXP81X found
bat_vol=412, ratio=100
[ 0.887]PMU: dcdc2 1100
[ 0.890]PMU: cpux 1008 Mhz,AXI=336 Mhz
PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz AHB2=300Mhz MBus=400Mhz
device_type = 3253, onoff=1
dcdc1_vol = 3300, onoff=1
dcdc2_vol = 1100, onoff=1
dcdc6_vol = 1100, onoff=1
aldo1_vol = 2800, onoff=0
aldo2_vol = 1800, onoff=1
aldo3_vol = 3000, onoff=1
dldo1_vol = 3300, onoff=0
dldo2_vol = 3300, onoff=0
dldo3_vol = 2800, onoff=0
dldo4_vol = 3300, onoff=1
eldo1_vol = 1800, onoff=1
eldo2_vol = 1800, onoff=0
eldo3_vol = 1800, onoff=0
fldo1_vol = 1200, onoff=0
fldo2_vol = 1100, onoff=1
gpio0_vol = 3100, onoff=0
vbus not exist
no battery, limit to dc
run key detect
key pressed value=0x1
key pressed value=0x1
fel key not configed
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
key pressed value=0x1
time out
key not pressed anymore
no uart input
DRAM: 1008 MiB
fdt addr: 0x76eb70e0
Relocation Offset is: 35f09000
In: serial
Out: serial
Err: serial
gic: sec monitor mode
[ 12.577]start
drv_disp_init
init_clocks: finish init_clocks.
enable power vcc-hdmi-33, ret=0
drv_disp_init finish
boot_disp.output_disp=0
boot_disp.output_type=3
boot_disp.output_type=10
fetch script data boot_disp.auto_hpd fail
disp0 device type(4) enable
attched ok, mgr0<-->device1, type=4, mode=10
[ 12.948]end
workmode = 0,storage type = 1
[ 12.952]MMC: 0
[mmc]: mmc driver ver 2015-07-29 14:10:00
SUNXI SD/MMC: 0
[mmc]: start mmc_calibrate_delay_unit, don't access device...
[mmc]: delay chain cal done, sample: 200(ps)
[mmc]: media type 0x0
[mmc]: Wrong media type 0x0
[mmc]: ************Try SD card 0************
[mmc]: host caps: 0x27
[mmc]: MID 1b PSN 008541f6
[mmc]: PNM 00000 -- 0x30-30-30-30-30
[mmc]: PRV 1.0
[mmc]: MDT m-12 y-2011
[mmc]: speed mode : HSSDR52/SDR25
[mmc]: clock : 50000000 Hz
[mmc]: bus_width : 4 bit
[mmc]: user capacity : 15423 MB
[mmc]: ************SD/MMC 0 init OK!!!************
[mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte
[mmc]: secure_feature : 0x0
[mmc]: secure_removal_type : 0x0
[ 13.167]sunxi flash init ok
--------fastboot partitions--------
-total partitions:11-
-name- -start- -size-
bootloader : 1000000 2000000
env : 3000000 1000000
boot : 4000000 1000000
system : 5000000 60000000
misc : 65000000 1000000
recovery : 66000000 2000000
cache : 68000000 30000000
metadata : 98000000 1000000
private : 99000000 1000000
alog : 9a000000 5000000
UDISK : 9f000000 0
-----------------------------------
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_mmc
key 1
recovery key high 12, low 10
fastboot key high 6, low 4
misc partition found
to be run cmd=run setargs_mmc boot_normal
update dtb dram start
update dtb dram end
** Unrecognized filesystem type **
load file(sn.txt) error
serial is: 241051900808142809cb
no battery exist
sunxi_bmp_logo_display
reading bootlogo.bmp
681774 bytes read in 36 ms (18.1 MiB/s)
bmp file buffer: 0x41000000, bmp_info.buffer: 47400000
fetch script data boot_disp.output_full fail
screen_id =0, screen_width =1920, screen_height =1080
frame buffer address 47400036
[ 13.776]inter uboot shell
Hit any key to stop autoboot: 0
read partition: boot or recovery
[ 14.608]sunxi flash read :offset 4000000, 16918757 bytes OK
Kernel load addr 0x41080000 size 10881 KiB
RAM disk load addr 0x42000000 size 4617 KiB
[ 14.955]ready to boot
prepare for kernel
[mmc]: MMC Device 2 not found
[mmc]: mmc 2 not find, so not exit
Starting kernel ...
INFO: BL3-1: Next image address = 0x41080000
INFO: BL3-1: Next image spsr = 0x3c5
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.65 (dogukan@dogukan-GE70-2OD) (gcc version 4.9.3 20150113 (prerelease) (Linaro GCC 4.9-2015.01-3) ) #3 SMP PREEMPT Wed Feb 3 14:42:22 EET 2016
[ 0.000000] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000] Machine: sun50iw1p1
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] cma: CMA: reserved 356 MiB at 69c00000
[ 0.000000] On node 0 totalpages: 258048
[ 0.000000] DMA zone: 3528 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 258048 pages, LIFO batch:31
[ 0.000000] script_init enter!
[ 0.000000] script_init exit!
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv0.2 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] PERCPU: Embedded 12 pages/cpu @ffffffc028b84000 s20224 r8192 d20736 u49152
[ 0.000000] pcpu-alloc: s20224 r8192 d20736 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 254520
[ 0.000000] Kernel command line: enforcing=1 earlyprintk=sunxi-uart,0x01c28000 initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p7 init=/init partitions=bootloader@mmcblk0p2:env@mmcblk0p5:boot@mmcblk0p6:system@mmcblk0p7:misc@mmcblk0p8:recovery@mmcblk0p9:cache@mmcblk0p10:metadata@mmcblk0p11:private@mmcblk0p12:alog@mmcblk0p13:UDISK@mmcblk0p1 cma=356M androidboot.serialno=241051900808142809cb androidboot.hardware=sun50iw1p1
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Memory: 1008MB = 1008MB total
[ 0.000000] Memory: 632476k/632476k available, 399716k reserved
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbbffff0000 (245759 MB)
[ 0.000000] vmemmap : 0xffffffbc00e38000 - 0xffffffbc01c00000 ( 13 MB)
[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc03f000000 ( 1008 MB)
[ 0.000000] .init : 0xffffffc0009e5000 - 0xffffffc000a68f00 ( 528 kB)
[ 0.000000] .text : 0xffffffc000080000 - 0xffffffc0009e4624 ( 9618 kB)
[ 0.000000] .data : 0xffffffc000a69000 - 0xffffffc000b20360 ( 733 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (virt).
[ 0.000000] Console: colour dummy device 80x25
[ 15.122118] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 15.132258] pid_max: default: 32768 minimum: 301
[ 15.137201] Security Framework initialized
[ 15.140807] SELinux: Initializing.
[ 15.144344] SELinux: Starting in enforcing mode
[ 15.148989] Mount-cache hash table entries: 256
[ 15.155006] Initializing cgroup subsys debug
[ 15.157333] Initializing cgroup subsys freezer
[ 15.161857] ftrace: allocating 25189 entries in 99 pages
[ 15.198312] CPU0: update cpu_power 1968128
[ 15.198345] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 15.206289] virtual base = 0xffffff800000a000.
[ 15.209204] gicd_base = 0xffffff800000c000.
[ 15.213342] gicc_base = 0xffffff800000e000.
[ 15.219485] CPU1: Booted secondary processor
[ 15.219507] CPU1: update cpu_power 1968128
[ 15.222110] CPU2: Booted secondary processor
[ 15.222123] CPU2: update cpu_power 1968128
[ 15.226229] CPU3: Booted secondary processor
[ 15.226240] CPU3: update cpu_power 1968128
[ 15.226324] Brought up 4 CPUs
[ 15.248276] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 15.255641] devtmpfs: initialized
[ 15.285191] atomic64 test passed
[ 15.285214] pinctrl core: initialized pinctrl subsystem
[ 15.299967] NET: Registered protocol family 16
[ 15.300544] script_sysfs_init success
[ 15.304657] dump_class_init,788, success
[ 15.307599] vdso: 2 pages (1 code, 1 data) at base ffffffc000a71000
[ 15.312393] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 15.320251] software IO TLB [mem 0x67c00000-0x68000000] (4MB) mapped at [ffffffc026c00000-ffffffc026ffffff]
[ 15.329740] DMA: preallocated 256 KiB pool for atomic allocations
[ 15.335355] axp81x_board_init: axp regl_devs num = 23
[ 15.339820] pll_audio-set_default_rate=24576000 success!
[ 15.344694] pll_video0-set_default_rate=297000000 success!
[ 15.350158] pll_video1-set_default_rate=297000000 success!
[ 15.355513] pll_de-set_default_rate=297000000 success!
[ 15.361536] de-set_default_source=pll_de success!
[ 15.365057] de-set_default_rate=297000000 success!
[ 15.369806] tcon0-set_default_source=pll_mipi success!
[ 15.374827] tcon1-set_default_source=pll_video0 success!
[ 15.380279] hdmi-set_default_source=pll_video0 success!
[ 15.388540] sun50i-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver
[ 15.392223] [sun50iw1p1_pinctrl_probe][838]
[ 15.398434] sun50i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 15.404925] sunxi hwspinlock vbase:0xffffff800005c000
[ 15.425654] sunxi_chipid_probe,150: soc bin:0
[ 15.480196] bio: create slab <bio-0> at 0
[ 15.481229] pwm module init!
[ 15.481707] sunxi_pwm pwm0.9: unable to map pwm registers
[ 15.486732] sunxi_pwm: probe of pwm0.9 failed with error -22
[ 15.496747] SCSI subsystem initialized
[ 15.497761] usbcore: registered new interface driver usbfs
[ 15.501483] usbcore: registered new interface driver hub
[ 15.507096] usbcore: registered new device driver usb
[ 15.513832] Linux video capture interface: v2.00
[ 15.518041] [ARISC] :sunxi-arisc driver v1.10
[ 15.539648] [ARISC] :sunxi-arisc driver v1.10 startup succeeded
[ 15.540571] Advanced Linux Sound Architecture Driver Initialized.
[ 15.547309] Bluetooth: Core ver 2.16
[ 15.549597] NET: Registered protocol family 31
[ 15.553740] Bluetooth: HCI device and connection manager initialized
[ 15.560004] Bluetooth: HCI socket layer initialized
[ 15.564764] Bluetooth: L2CAP socket layer initialized
[ 15.569748] Bluetooth: SCO socket layer initialized
[ 15.575412] cfg80211: Calling CRDA to update world regulatory domain
[ 15.581439] [pm]aw_pm_init!
[ 15.583488] rtc physical base = 0x0000000001f00000 .
[ 15.588420] np name = /soc@01c00000/rtc@01f00000.
[ 15.593055] base = ffffff800006c100, len = 4.
[ 15.597318] pmu name: pmu0 .
[ 15.600176] pmu0_enable = 0x1.
[ 15.603204] pmux_id = 0x6.
[ 15.605933] pmux_twi_id = 0x1.
[ 15.609002] pmux_twi_addr = 0x34.
[ 15.612337] pmu name: pmu1 .
[ 15.615191] Warning: can not find np for pmu1.
[ 15.619817] add_sys_pwr_dm: get ldo name for id: vcc-lpddr failed
[ 15.625792] after inited: sys_mask config = 0x4a55.
[ 15.630510] Warning: can not find np for dynamic_standby_para.
[ 15.636411] [pm]valid
[ 15.638507] [pm]valid
[ 15.640725] Notice: sun9i&sun8iw5&sun50i not need support normal standby, change to super standby.
[ 15.650154] Switching to clocksource arch_sys_counter
[ 15.695430] FS-Cache: Loaded
[ 15.695969] CacheFiles: Loaded
[ 15.721746] NET: Registered protocol family 2
[ 15.723180] TCP established hash table entries: 8192 (order: 5, 131072 bytes)
[ 15.727655] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ 15.734030] TCP: Hash tables configured (established 8192 bind 8192)
[ 15.741163] TCP: reno registered
[ 15.743262] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 15.749092] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 15.756087] NET: Registered protocol family 1
[ 15.760474] Unpacking initramfs...
[ 15.999565] Freeing initrd memory: 4616K (ffffffc001000000 - ffffffc001482000)
[ 16.002928] lock super standby defaultly!
[ 16.005051] lookup_scene_lock_name: new scene lock super_standby
[ 16.010950] scene_lock_init name=super_standby
[ 16.015279] scene_lock: super_standby, type 5, count 1
[ 16.021557] audit: initializing netlink socket (disabled)
[ 16.025664] type=2000 audit(0.820:1): initialized
[ 16.034858] NTFS driver 2.1.30 [Flags: R/W].
[ 16.035112] fuse init (API version 7.22)
[ 16.039344] msgmni has been set to 1956
[ 16.042083] SELinux: Registering netfilter hooks
[ 16.048623] NET: Registered protocol family 38
[ 16.050980] io scheduler noop registered
[ 16.054763] io scheduler deadline registered
[ 16.059085] io scheduler cfq registered (default)
[ 16.065522] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
[ 16.069463] sw_console_setup()1173 - console setup baud 115200 parity n bits 8, flow n
[ 16.077282] console [ttyS0] enabled, bootconsole disabled
[ 16.077282] console [ttyS0] enabled, bootconsole disabled
[ 16.089485] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI
[ 16.101269] misc dump reg init
[ 16.112321] loop: module loaded
[ 16.116068] sunxi-bt bt.27: Missing bt_power.
[ 16.120845] sunxi-bt bt.27: bt_power_name ((null))
[ 16.126080] sunxi-bt bt.27: io_regulator_name (vcc-wifi-io)
[ 16.132205] sunxi-bt bt.27: bt_rst gpio=356 mul-sel=1 pull=-1 drv_level=-1 data=0
[ 16.140807] sunxi-bt bt.27: clk not config
[ 16.145579] sunxi-bt bt.27: block state already is 1
[ 16.151457] sunxi-wlan wlan.26: wlan_busnum (1)
[ 16.156404] sunxi-wlan wlan.26: Missing wlan_power.
[ 16.161741] sunxi-wlan wlan.26: wlan_power_name ((null))
[ 16.167554] sunxi-wlan wlan.26: io_regulator_name (vcc-wifi-io)
[ 16.174041] sunxi-wlan wlan.26: wlan_regon gpio=354 mul-sel=1 pull=-1 drv_level=-1 data=0
[ 16.183388] sunxi-wlan wlan.26: wlan_hostwake gpio=355 mul-sel=6 pull=-1 drv_level=-1 data=0
[ 16.193017] sunxi-wlan wlan.26: clk not config
[ 16.200911] tun: Universal TUN/TAP device driver, 1.6
[ 16.206445] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 16.214272] WARNING: Get ephy clock is failed
[ 16.220306] PPP generic driver version 2.4.2
[ 16.225655] PPP BSD Compression module registered
[ 16.230790] PPP Deflate Compression module registered
[ 16.236325] PPP MPPE Compression module registered
[ 16.241555] NET: Registered protocol family 24
[ 16.246458] PPTP driver version 0.8.5
[ 16.250713] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 16.258255] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 16.265560] usbcore: registered new interface driver usb-storage
[ 16.272316] usbcore: registered new interface driver ums-alauda
[ 16.278978] usbcore: registered new interface driver ums-cypress
[ 16.285732] usbcore: registered new interface driver ums-datafab
[ 16.292471] usbcore: registered new interface driver ums_eneub6250
[ 16.299417] usbcore: registered new interface driver ums-freecom
[ 16.306169] usbcore: registered new interface driver ums-isd200
[ 16.312818] usbcore: registered new interface driver ums-jumpshot
[ 16.319670] usbcore: registered new interface driver ums-karma
[ 16.326248] usbcore: registered new interface driver ums-onetouch
[ 16.333102] usbcore: registered new interface driver ums-realtek
[ 16.339850] usbcore: registered new interface driver ums-sddr09
[ 16.346510] usbcore: registered new interface driver ums-sddr55
[ 16.353154] usbcore: registered new interface driver ums-usbat
[ 16.360252] usbcore: registered new interface driver usbserial
[ 16.366821] usbcore: registered new interface driver option
[ 16.373083] usbserial: USB Serial support registered for GSM modem (1-port)
[ 16.381859] mousedev: PS/2 mouse device common for all mice
[ 16.388401] usbcore: registered new interface driver xpad
[ 16.394498] usbcore: registered new interface driver usb_acecad
[ 16.401150] usbcore: registered new interface driver aiptek
[ 16.407451] usbcore: registered new interface driver gtco
[ 16.413548] usbcore: registered new interface driver hanwang
[ 16.419922] usbcore: registered new interface driver kbtab
[ 16.426114] usbcore: registered new interface driver wacom
[ 16.434205] sunxi-rtc 1f00000.rtc: rtc core: registered rtc-sunxi as rtc0
[ 16.441661] sunxi-rtc 1f00000.rtc: RTC enabled
[ 16.447118] IR NEC protocol handler initialized
[ 16.452075] IR RC5(x) protocol handler initialized
[ 16.457304] IR RC6 protocol handler initialized
[ 16.462256] IR JVC protocol handler initialized
[ 16.467200] IR Sony protocol handler initialized
[ 16.472246] IR RC5 (streamzap) protocol handler initialized
[ 16.478329] IR SANYO protocol handler initialized
[ 16.483469] IR MCE Keyboard/mouse protocol handler initialized
[ 16.490279] Registered IR keymap rc_map_sunxi
[ 16.496012] input: sunxi_ir_recv as /devices/soc.0/1f02000.s_cir/rc/rc0/input0
[ 16.504320] rc0: sunxi_ir_recv as /devices/soc.0/1f02000.s_cir/rc/rc0
[ 16.511871] input: MCE IR Keyboard/Mouse (sunxi-rc-recv) as /devices/virtual/input/input1
[ 16.522100] sunxi cedar version 0.1
[ 16.526106] [cedar]: install start!!!
[ 16.530184] ycy the get irq is 90
[ 16.534431] ycy clk_bass_vir 0x18 is ffffff800009a018, the value:3006207
[ 16.541855] ycy clk_bass_vir 0x13c is ffffff800009a13c, the value:0
[ 16.548793] ycy clk_bass_vir 0x64 is ffffff800009a064, the value:601810
[ 16.556120] ycy clk_bass_vir 0x2c4 is ffffff800009a2c4, the value:601c10
[ 16.563540] ycy clk_bass_vir 0x100 is ffffff800009a100, the value:0
[ 16.570483] [cedar]: install end!!!
[ 16.580653] input: axp81x-supplyer as /devices/platform/axp81x_board/axp81x-supplyer.47/input/input2
[ 16.604575] sunxi budget cooling probe start !
[ 16.609474] CPU freq cooling register Success
[ 16.614243] CPU hotplug cooling register Success
[ 16.619645] CPU budget cooling register Success
[ 16.625260] sunxi gpu cooling probe start !
[ 16.629847] CPU gpu cooling register Success
[ 16.634890] device-mapper: uevent: version 1.0.3
[ 16.640478] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 16.649926] Bluetooth: HCI UART driver ver 2.2
[ 16.654778] Bluetooth: HCI H4 protocol initialized
[ 16.660045] Bluetooth: HCI Three-wire UART (H5) protocol initialized
[ 16.670114] cpuidle: using governor ladder
[ 16.674584] cpuidle: using governor menu
[ 16.679852] sunxi-mmc 1c0f000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.17 2015-6-16 10:35) Compiled in Jan 30 2016 at 21:06:32
[ 16.692776] sunxi-mmc 1c0f000.sdmmc: regulator prop vmmc,str none
[ 16.699443] sunxi-mmc 1c0f000.sdmmc: regulator prop vqmmc,str none
[ 16.706195] sunxi-mmc 1c0f000.sdmmc: regulator prop vdmmc,str vcc-sdc
[ 16.713343] sunxi-mmc 1c0f000.sdmmc: No vmmc regulator found
[ 16.719637] sunxi-mmc 1c0f000.sdmmc: No vqmmc regulator found
[ 16.726483] sunxi-mmc 1c0f000.sdmmc: Got CD GPIO #166.
[ 16.732446] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 16.743426] sunxi-mmc 1c0f000.sdmmc: no vqmmc,Check if there is regulator
[ 16.766824] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 16.796304] sunxi-mmc 1c0f000.sdmmc: base:0xffffff800009c000 irq:92
[ 16.803693] sunxi-mmc 1c10000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.17 2015-6-16 10:35) Compiled in Jan 30 2016 at 21:06:32
[ 16.816573] sunxi-mmc 1c10000.sdmmc: Can't get vmmc regulator string
[ 16.823512] sunxi-mmc 1c10000.sdmmc: Can't get vqmmc regulator string
[ 16.830571] sunxi-mmc 1c10000.sdmmc: Can't get vdmmc regulator string
[ 16.837611] get() with no identifier
[ 16.841509] get() with no identifier
[ 16.845407] get() with no identifier
[ 16.849328] sunxi-mmc 1c10000.sdmmc: No vmmc regulator found
[ 16.855525] sunxi-mmc 1c10000.sdmmc: No vqmmc regulator found
[ 16.861799] sunxi-mmc 1c10000.sdmmc: No vdmmc regulator found
[ 16.868799] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 16.879762] sunxi-mmc 1c10000.sdmmc: no vqmmc,Check if there is regulator
[ 16.895495] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 52, RTO !!
[ 16.902958] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 52, RTO !!
[ 16.904529] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 16.921020] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 16.924234] sunxi-mmc 1c10000.sdmmc: base:0xffffff80000a4000 irq:93
[ 16.941767] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 16.941894] hidraw: raw HID events driver (C) Jiri Kosina
[ 16.953443] usbcore: registered new interface driver usbhid
[ 16.953446] usbhid: USB HID core driver
[ 16.954337] zram: Created 1 device(s) ...
[ 16.974838] ashmem: initialized
[ 16.975967] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !!
[ 16.976779] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !!
[ 16.977591] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !!
[ 16.978403] sunxi-mmc 1c0f000.sdmmc: smc 0 p0 err, cmd 5, RTO !!
[ 16.979035] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B
[ 16.979086] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B
[ 16.981460] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing LEGACY(SDR12) dt B
[ 17.009940] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 17.011737] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B
[ 17.011792] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 1 timing SD-HS(SDR25) dt B
[ 17.011895] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 16 width 4 timing SD-HS(SDR25) dt B
[ 17.011918] mmc0: new high speed SDHC card at address b368
[ 17.088244] logger: created 256K log 'log_main'
[ 17.088743] mmcblk0: mmc0:b368 00000 15.0 GiB
[ 17.091253] mmcblk0: p1 p2 p3 < p5 p6 p7 p8 p9 p10 p11 p12 p13 >
[ 17.096229] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 17.097037] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 17.097053] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 17.099459] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 17.101275] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 8, RTO !!
[ 17.102079] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 17.102883] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 17.103688] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 17.104492] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 17.105299] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !!
[ 17.106103] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !!
[ 17.106908] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !!
[ 17.107713] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 55, RTO !!
[ 17.107728] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 17.108563] sunxi-mmc 1c10000.sdmmc: smc 1 p1 err, cmd 1, RTO !!
[ 17.108580] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[ 17.229567] logger: created 256K log 'log_events'
[ 17.235024] logger: created 256K log 'log_radio'
[ 17.240387] logger: created 256K log 'log_system'
[ 17.255467] sunxi-codec-machine sound.6: codec-aif1 <-> 1c22c00.i2s0-controller mapping ok
[ 17.265084] sunxi-codec-machine sound.6: codec-aif2 <-> bb-dai mapping ok
[ 17.273021] sunxi-codec-machine sound.6: codec-aif2 <-> bb-dai mapping ok
[ 17.280977] sunxi-codec-machine sound.6: codec-aif3 <-> bb-dai mapping ok
[ 17.291597] input: audiocodec sunxi Audio Jack as /devices/soc.0/sound.6/sound/card0/input3
[ 17.302946] sndhdmi sound.7: sndhdmi <-> 1c22800.daudio mapping ok
[ 17.311518] u32 classifier
[ 17.314472] Actions configured
[ 17.318199] Netfilter messages via NETLINK v0.30.
[ 17.323430] nf_conntrack version 0.5.0 (7825 buckets, 31300 max)
[ 17.330447] ctnetlink v0.93: registering with nfnetlink.
[ 17.338161] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 17.345763] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 17.353308] xt_time: kernel timezone is -0000
[ 17.358185] ipip: IPv4 over IPv4 tunneling driver
[ 17.364297] gre: GRE over IPv4 demultiplexor driver
[ 17.369632] ip_gre: GRE over IPv4 tunneling driver
[ 17.377051] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 17.383256] arp_tables: (C) 2002 David S. Miller
[ 17.388411] TCP: bic registered
[ 17.391835] TCP: cubic registered
[ 17.395441] TCP: westwood registered
[ 17.399349] TCP: htcp registered
[ 17.402867] Initializing XFRM netlink socket
[ 17.407833] NET: Registered protocol family 10
[ 17.415037] mip6: Mobile IPv6
[ 17.418358] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 17.424663] sit: IPv6 over IPv4 tunneling driver
[ 17.430958] NET: Registered protocol family 17
[ 17.435886] NET: Registered protocol family 15
[ 17.441222] Bluetooth: RFCOMM TTY layer initialized
[ 17.446597] Bluetooth: RFCOMM socket layer initialized
[ 17.452205] Bluetooth: RFCOMM ver 1.11
[ 17.456295] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 17.462092] Bluetooth: BNEP filters: protocol multicast
[ 17.467825] Bluetooth: BNEP socket layer initialized
[ 17.473244] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 17.479736] Bluetooth: HIDP socket layer initialized
[ 17.485758] Registering SWP/SWPB emulation handler
[ 17.492930] get usb_serial_number success from boot command line
[ 17.499724] init: failed to probe driver -19[ 17.504770] sunxi-rtc 1f00000.rtc: setting system clock to 2010-01-01 00:00:12 UTC (1262304012)
[ 17.515397] input: sunxi-ths as /devices/virtual/input/input4
[ 17.522003] thermal thermal_zone0: failed to read out thermal zone 0
[ 17.537004] ALSA device list:
[ 17.540252] #0: audiocodec
[ 17.543391] #1: sndhdmi
[ 17.546844] Freeing unused kernel memory: 524K (ffffffc0009e5000 - ffffffc000a68000)
[ 17.557609] init: init started!
[ 17.570973] SELinux: 2048 avtab hash slots, 4929 rules.
[ 17.582239] SELinux: 2048 avtab hash slots, 4929 rules.
[ 17.587994] SELinux: 1 users, 2 roles, 531 types, 0 bools, 1 sens, 1024 cats
[ 17.595844] SELinux: 87 classes, 4929 rules
[ 17.603928] SELinux: Completing initialization.
[ 17.608973] SELinux: Setting up existing superblocks.
[ 17.614613] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
[ 17.622417] SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
[ 17.630511] SELinux: initialized (dev bdev, type bdev), not configured for labeling
[ 17.638912] SELinux: initialized (dev proc, type proc), uses genfs_contexts
[ 17.646544] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[ 17.654457] SELinux: initialized (dev devtmpfs, type devtmpfs), uses transition SIDs
[ 17.663329] SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
[ 17.676407] SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
[ 17.683954] SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
[ 17.691466] SELinux: initialized (dev anon_inodefs, type anon_inodefs), not configured for labeling
[ 17.701378] SELinux: initialized (dev devpts, type devpts), uses transition SIDs
[ 17.709489] SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
[ 17.718119] SELinux: initialized (dev configfs, type configfs), not configured for labeling
[ 17.727253] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[ 17.735166] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
[ 17.933604] type=1403 audit(1262304012.930:2): policy loaded auid=4294967295 ses=4294967295
[ 17.943459] init: (Initializing SELinux enforcing took 0.39s.)
[ 17.956085] init: init second stage started!
[ 18.013646] init: waitpid failed: No child processes
[ 18.019341] init: (Loading properties from /default.prop took 0.00s.)
[ 18.028435] init: (Parsing /init.environ.rc took 0.00s.)
[ 18.034555] init: (Parsing /init.usb.rc took 0.00s.)
[ 18.040662] init: (Parsing init.common.rc took 0.00s.)
[ 18.046496] init: (Parsing init.sun50iw1p1.usb.rc took 0.00s.)
[ 18.052963] init: (Parsing init.zygote64_32.rc took 0.00s.)
[ 18.059074] init: (Parsing /init.sun50iw1p1.rc took 0.02s.)
[ 18.065554] init: (Parsing /init.usb.configfs.rc took 0.00s.)
[ 18.071917] init: /init.zygote64_32.rc: 1: ignored duplicate definition of service 'zygote'
[ 18.081073] init: /init.zygote64_32.rc: 10: ignored duplicate definition of service 'zygote_secondary'
[ 18.091262] init: (Parsing /init.zygote64_32.rc took 0.02s.)
[ 18.097595] init: (Parsing /init.trace.rc took 0.00s.)
[ 18.103271] init: could not import file '/init.cm.rc' from '/init.rc'
[ 18.110358] init: (Parsing /init.rc took 0.08s.)
[ 18.115622] init: SELinux: Could not get canonical path /adb_keys restorecon: No such file or directory.
[ 18.126083] init: Starting service 'ueventd'...
[ 18.131441] init: Waiting for /dev/.coldboot_done...
[ 18.133671] ueventd: ueventd started!
[ 18.533222] ueventd: Coldboot took 0.40s.
[ 18.538854] init: Waiting for /dev/.coldboot_done took 0.41s.
[ 18.545211] init: /dev/hw_random not found
[ 18.551491] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[ 18.560239] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[ 18.570692] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[ 18.583966] init: write_file: Unable to open '/proc/cpu/alignment': No such file or directory
[ 18.593650] init: write_file: Unable to open '/proc/sys/kernel/sched_compat_yield': No such file or directory
[ 18.606591] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[ 18.614912] init: write_file: Unable to write to '/dev/cpuctl/cpu.shares': Invalid argument
[ 18.625888] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[ 18.639184] SELinux: initialized (dev pstore, type pstore), uses genfs_contexts
[ 18.647577] init: write_file: Unable to open '/proc/sys/abi/swp': No such file or directory
[ 18.657529] type=1400 audit(1262304013.670:3): avc: denied { create } for pid=1 comm="init" name="sdcard" scontext=u:r:init:s0 tcontext=u:object_r:tmpfs:s0 tclass=lnk_file permissive=0
[ 18.676549] type=1400 audit(1262304013.690:4): avc: denied { create } for pid=1 comm="init" name="extsd" scontext=u:r:init:s0 tcontext=u:object_r:tmpfs:s0 tclass=lnk_file permissive=0
[ 18.695584] type=1400 audit(1262304013.710:5): avc: denied { create } for pid=1 comm="init" name="usbhost" scontext=u:r:init:s0 tcontext=u:object_r:tmpfs:s0 tclass=lnk_file permissive=0
[ 18.714477] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[ 18.722911] init: /dev/hw_random not found
[ 18.745505] type=1400 audit(1262304013.760:6): avc: denied { sys_module } for pid=1 comm="init" capability=16 scontext=u:r:init:s0 tcontext=u:r:init:s0 tclass=capability permissive=0
[ 18.766724] init: Warning! Service exec 0 (/sbin/busybox) needs a SELinux domain defined; please fix!
[ 18.776970] init: Starting service 'exec 0 (/sbin/busybox)'...
[ 18.784117] type=1400 audit(1262304013.800:7): avc: denied { execute_no_trans } for pid=1375 comm="init" path="/sbin/busybox" dev="rootfs" ino=3976 scontext=u:r:init:s0 tcontext=u:object_r:rootfs:s0 tclass=file permissive=0
[ 18.806122] init: cannot execve('/sbin/busybox'): Permission denied
[ 18.813273] init: Service 'exec 0 (/sbin/busybox)' (pid 1375) exited with status 127
[ 37.847231] fs_mgr: __mount(source=/dev/block/by-name/system,target=/system,type=ext4)=-1
[ 37.856271] fs_mgr: Failed to mount an un-encryptable or wiped partition on/dev/block/by-name/system at /system options: (null) error: No such file or directory