+- PINE64 (https://forum.pine64.org)
+-- Forum: ROCKPRO64 (https://forum.pine64.org/forumdisplay.php?fid=98)
+--- Forum: General Discussion on ROCKPRO64 (https://forum.pine64.org/forumdisplay.php?fid=99)
+--- Thread: Can't get Rockpro to boot (/showthread.php?tid=6959)
Can't get Rockpro to boot - Crnppscls - 12-14-2018
I've been on for a week or so when i've had time but i'm still unable to get anything from Hdmi.
Both lights on the ethernet are solid as well as the green light next to the psu in. I have never seen the white light behind the reset switch lit.
I have a 32GB emmc and a decent samsung sd card, i've written ubuntu minimal to both but have been unable to boot anything. Windows does throw a bit of a hissy after writing with etcher but the image appears to be valid, i've also tried other images.
Psu is 12v @3000mA. I could possibly try another but don't have one to hand and that is probably now the only thing i have left to do, unless windows is botching the writing process.
I wondered if there was something i have missed, i don't have much experience with Sbc's and i'm really struggling with this one.
RE: Can't get Rockpro to boot - evilbunny - 12-15-2018
(12-14-2018, 06:51 PM)Crnppscls Wrote: I've been on for a week or so when i've had time but i'm still unable to get anything from Hdmi.
Both lights on the ethernet are solid as well as the green light next to the psu in. I have never seen the white light behind the reset switch lit.
I have a 32GB emmc and a decent samsung sd card, i've written ubuntu minimal to both but have been unable to boot anything. Windows does throw a bit of a hissy after writing with etcher but the image appears to be valid, i've also tried other images.
Psu is 12v @3000mA. I could possibly try another but don't have one to hand and that is probably now the only thing i have left to do, unless windows is botching the writing process.
I wondered if there was something i have missed, i don't have much experience with Sbc's and i'm really struggling with this one.
Which image did you write to emmc?
RE: Can't get Rockpro to boot - Crnppscls - 12-15-2018
(12-15-2018, 12:13 AM)evilbunny Wrote:(12-14-2018, 06:51 PM)Crnppscls Wrote: I've been on for a week or so when i've had time but i'm still unable to get anything from Hdmi.
Both lights on the ethernet are solid as well as the green light next to the psu in. I have never seen the white light behind the reset switch lit.
I have a 32GB emmc and a decent samsung sd card, i've written ubuntu minimal to both but have been unable to boot anything. Windows does throw a bit of a hissy after writing with etcher but the image appears to be valid, i've also tried other images.
Psu is 12v @3000mA. I could possibly try another but don't have one to hand and that is probably now the only thing i have left to do, unless windows is botching the writing process.
I wondered if there was something i have missed, i don't have much experience with Sbc's and i'm really struggling with this one.
Which image did you write to emmc?
This one: http://wiki.pine64.org/index.php/ROCKPro64_Software_Release#Minimal_aarch64_.5BmicroSD_.2F_eMMC_Boot.5D_.5B0.7.9.5D_2
RE: Can't get Rockpro to boot - Bullet64 - 12-15-2018
When the white led don't turn on, the rockpro64 don't boot. So wrong image and so on....
Please test with this image -> http://wiki.pine64.org/index.php/ROCKPro64_Software_Release#Armbian_Debian_Stretch_.5BmicroSD_.2F_eMMC_Boot.5D_.5B5.67.5D
RE: Can't get Rockpro to boot - Crnppscls - 12-15-2018
(12-15-2018, 04:39 PM)Bullet64 Wrote: When the white led don't turn on, the rockpro64 don't boot. So wrong image and so on....
Please test with this image -> http://wiki.pine64.org/index.php/ROCKPro64_Software_Release#Armbian_Debian_Stretch_.5BmicroSD_.2F_eMMC_Boot.5D_.5B5.67.5D
I burnt the image to the sd card and emmc, unfortunately there is still nothing coming from hdmi. My monitor just goes into standby because there is no signal, i even tried it on my tv and there was nothing.
I tried the emmc and sc card together, then individually and the result was still the same.
Thanks for your help though, i think i'm going to have to Rma the board, which is a shame because it's going to be well into the new year before a replacement arrives