PINE64
Kernel Panic on Rock64 linux - Printable Version

+- PINE64 (https://forum.pine64.org)
+-- Forum: ROCK64 (https://forum.pine64.org/forumdisplay.php?fid=85)
+--- Forum: General Discussion on ROCK64 (https://forum.pine64.org/forumdisplay.php?fid=86)
+--- Thread: Kernel Panic on Rock64 linux (/showthread.php?tid=5011)

Pages: 1 2


Kernel Panic on Rock64 linux - tanisou - 08-24-2017

About My Rock64 occurred kernel panic.

I bought four Rock64 board.
2 of 4GB model,2 of 2GB model.
Other 3 boards works well.
One of 4GB model occurrd this problem every time.
Im using newest xenial-minimum and xenial-mate on MicroSD.
Power supply to GPIO 5V and GND by iPad Pro's 5V 2.4A charger.
But other 3 board work well under same MicroSD,OS image,charger.
So I think comatibility problem(or initial failure?)

movie:xenial minimum on microSD
pictureConfusedame(https://drive.google.com/file/d/0B58MjMVkTjfWZkxTX3phd0V3eTA/view?usp=sharing)
I know how to fix this problem.
Sorry my bad english and Thank you forum member 







RE: Kernel Panic on Rock64 linux - MarkHaysHarris777 - 08-25-2017

Does the board panic using all SD cards ?  If so, and if all SD card work in the other boards, then we can assume a hardware failure this one board;  open a support ticket.

Before you do that;  check the board over with a glass, or scope (eye piece),  to determine if any solder balls are left on the board from mfg;  this does occur unfortunately ( I actually had one board with this problem ).  Carefully check all spaces, pins, around all chips, in every connector;  also look for solder bridges.


RE: Kernel Panic on Rock64 linux - tanisou - 08-25-2017

(08-25-2017, 12:49 AM)MarkHaysHarris777 Wrote: Does the board panic using all SD cards ?  If so, and if all SD card work in the other boards, then we can assume a hardware failure this one board;  open a support ticket.

Before you do that;  check the board over with a glass, or scope (eye piece),  to determine if any solder balls are left on the board from mfg;  this does occur unfortunately ( I actually had one board with this problem ).  Carefully check all spaces, pins, around all chips, in every connector;  also look for solder bridges.

Thank you for reply.
I tried samsung,toshiba,and sillicon power Micro SD card.
But it is not changed.
I saw using ocula glass,I look for solder bridge around surface mount resister.
But I dont know this is cause of this problem or not.


RE: Kernel Panic on Rock64 linux - MarkHaysHarris777 - 08-25-2017

(08-25-2017, 02:40 AM)tanisou Wrote:
(08-25-2017, 12:49 AM)MarkHaysHarris777 Wrote: Does the board panic using all SD cards ?  If so, and if all SD card work in the other boards, then we can assume a hardware failure this one board;  open a support ticket.

Before you do that;  check the board over with a glass, or scope (eye piece),  to determine if any solder balls are left on the board from mfg;  this does occur unfortunately ( I actually had one board with this problem ).  Carefully check all spaces, pins, around all chips, in every connector;  also look for solder bridges.

Thank you for reply.
I tried samsung,toshiba,and sillicon power Micro SD card.
But it is not changed.
I saw using ocula glass,I look for solder bridge around surface mount resister.
But I dont know this is cause of this problem or not.

can you post a close-in pic ?


RE: Kernel Panic on Rock64 linux - tanisou - 08-25-2017

(08-25-2017, 04:50 AM)MarkHaysHarris777 Wrote:
(08-25-2017, 02:40 AM)tanisou Wrote:
(08-25-2017, 12:49 AM)MarkHaysHarris777 Wrote: Does the board panic using all SD cards ?  If so, and if all SD card work in the other boards, then we can assume a hardware failure this one board;  open a support ticket.

Before you do that;  check the board over with a glass, or scope (eye piece),  to determine if any solder balls are left on the board from mfg;  this does occur unfortunately ( I actually had one board with this problem ).  Carefully check all spaces, pins, around all chips, in every connector;  also look for solder bridges.

Thank you for reply.
I tried samsung,toshiba,and sillicon power Micro SD card.
But it is not changed.
I saw using ocula glass,I look for solder bridge around surface mount resister.
But I dont know this is cause of this problem or not.

can you post a close-in pic ?

I suspicious this https://drive.google.com/open?id=0B58MjMVkTjfWZUdQRVp3RFI4SkE








RE: Kernel Panic on Rock64 linux - MarkHaysHarris777 - 08-25-2017

(08-25-2017, 05:54 AM)tanisou Wrote:
(08-25-2017, 04:50 AM)MarkHaysHarris777 Wrote:
(08-25-2017, 02:40 AM)tanisou Wrote:
(08-25-2017, 12:49 AM)MarkHaysHarris777 Wrote: Does the board panic using all SD cards ?  If so, and if all SD card work in the other boards, then we can assume a hardware failure this one board;  open a support ticket.

Before you do that;  check the board over with a glass, or scope (eye piece),  to determine if any solder balls are left on the board from mfg;  this does occur unfortunately ( I actually had one board with this problem ).  Carefully check all spaces, pins, around all chips, in every connector;  also look for solder bridges.

Thank you for reply.
I tried samsung,toshiba,and sillicon power Micro SD card.
But it is not changed.
I saw using ocula glass,I look for solder bridge around surface mount resister.
But I dont know this is cause of this problem or not.

can you post a close-in pic ?

I suspicious this https://drive.google.com/open?id=0B58MjMVkTjfWZUdQRVp3RFI4SkE







Yes,  that is definitely a problem, but easily fixed !


RE: Kernel Panic on Rock64 linux - tanisou - 08-25-2017

But How to fix it?


RE: Kernel Panic on Rock64 linux - MarkHaysHarris777 - 08-25-2017

(08-25-2017, 08:11 AM)tanisou Wrote: But How to fix it?

Its actually very easy ( really ).

... you use a 25 watt soldering iron and a tooth pick.  A hot air gun soldering station would be better, but if you don't have that ( they are pricey ) don't worry about it.

Basically you het the component carefully and you use the tooth pic to push it over where it belongs !

The pick&place robot slipped, or the component slipped in the oven. If you heat it and move it back it may work.  Depends on whether any damage occurred.  

Make sure YOU don't create any solder bridges ( you can used solder braid to clean it up if you do ).

( just don't do that )

Give it a shot;  like my old boss used to say, you can't break broke.    Blush


RE: Kernel Panic on Rock64 linux - tanisou - 08-25-2017

Thank you for teach me method.
I tried to fix it.
pic: https://drive.google.com/open?id=0B58MjMVkTjfWTnZ4X1FJVVM4X00
After fixed it,I turn on Rock64.
But displayed same kernel panic error...

And I notice this spot become hotter than SoC chip.
https://drive.google.com/open?id=0B58MjMVkTjfWX21Nb1VVTlZMTEU
https://drive.google.com/open?id=0B58MjMVkTjfWRDhoTF9ZSncxeWs


RE: Kernel Panic on Rock64 linux - MarkHaysHarris777 - 08-25-2017

(08-25-2017, 07:26 PM)tanisou Wrote: Thank you for teach me method.
I tried to fix it.
pic: https://drive.google.com/open?id=0B58MjMVkTjfWTnZ4X1FJVVM4X00
After fixed it,I turn on Rock64.
But displayed same kernel panic error...

And I notice this spot become hotter than SoC chip.
https://drive.google.com/open?id=0B58MjMVkTjfWX21Nb1VVTlZMTEU
https://drive.google.com/open?id=0B58MjMVkTjfWRDhoTF9ZSncxeWs

well, you gave it the good 'ol college try !   open a support ticket and get that thing replaced .