(08-17-2023, 07:13 AM)Corconegre Wrote: Hi all,
after a month using my pinetab2 the screen started flickering one day then i got a screen with colored vertical thin lines (image attached), and now it does not start at all.
I did not do any software upgrade during the weeks previous to this happening and i'm running the installation that came with the device.

I tried to plug the UART to the lower usb-c and followed the instructions here:
https://wiki.pine64.org/wiki/PineTab2#Connecting_the_UART_adapter 
To see if i could see something but it looks like the device does not even start, i also tried to reset it (using the press 7 seconds, 3 second wait, 3-4 seconds press) several times but nothing happens, also left it charging overnight without any result.
From the outside i do not see any light or anything else, just the green light on the UART when it's plugged via USB to the computer.

Anyone can give me advice on what to do next? i'm a bit lost now.

Thanks!

(08-23-2023, 02:57 PM)tllim Wrote:

(08-17-2023, 07:13 AM)Corconegre Wrote: Hi all,
after a month using my pinetab2 the screen started flickering one day then i got a screen with colored vertical thin lines (image attached), and now it does not start at all.
I did not do any software upgrade during the weeks previous to this happening and i'm running the installation that came with the device.

I tried to plug the UART to the lower usb-c and followed the instructions here:
https://wiki.pine64.org/wiki/PineTab2#Connecting_the_UART_adapter 
To see if i could see something but it looks like the device does not even start, i also tried to reset it (using the press 7 seconds, 3 second wait, 3-4 seconds press) several times but nothing happens, also left it charging overnight without any result.
From the outside i do not see any light or anything else, just the green light on the UART when it's plugged via USB to the computer.

Anyone can give me advice on what to do next? i'm a bit lost now.

Thanks!

Try to reseat the LCD ribbon cable and check whether help.

(08-24-2023, 10:10 AM)Corconegre Wrote:

(08-23-2023, 02:57 PM)tllim Wrote:

(08-17-2023, 07:13 AM)Corconegre Wrote: Hi all,
after a month using my pinetab2 the screen started flickering one day then i got a screen with colored vertical thin lines (image attached), and now it does not start at all.
I did not do any software upgrade during the weeks previous to this happening and i'm running the installation that came with the device.

I tried to plug the UART to the lower usb-c and followed the instructions here:
https://wiki.pine64.org/wiki/PineTab2#Connecting_the_UART_adapter 
To see if i could see something but it looks like the device does not even start, i also tried to reset it (using the press 7 seconds, 3 second wait, 3-4 seconds press) several times but nothing happens, also left it charging overnight without any result.
From the outside i do not see any light or anything else, just the green light on the UART when it's plugged via USB to the computer.

Anyone can give me advice on what to do next? i'm a bit lost now.

Thanks!

Try to reseat the LCD ribbon cable and check whether help.

Thanks for your answer, however if it was the cable, then i should see something connecting the UART right?
Is there any way i can open a "support ticket" for this?

(08-31-2023, 03:08 PM)Corconegre Wrote: Thanks!
thicket opened and got quite a fast reply, on the way so solve it.

(12-25-2023, 02:24 PM)zkajdan Wrote:

(08-31-2023, 03:08 PM)Corconegre Wrote: Thanks!
thicket opened and got quite a fast reply, on the way so solve it.

Would you mind letting me know how you solved it?

I seem to have a similar problem - did a sudo pacman -Syu, in the middle of the update, it crashed, I powered it off, and never was able to boot it again (also, nothing to see when connecting to laptop, just like in your case).

Many thanks!

(06-02-2024, 04:11 PM)angeloweb Wrote: My Pinetab2 does not appear to be accepting power. It worked for months, then, after being untouched (while plugged in) for a couple of weeks, it wouldn't work right. Even with power plugged in the power-port, won't start.

Shortly before the battery totally drained, it would try to power on for a couple of seconds, then turn off.

Tried multiple cables & charging devices. I figure that even if the battery is having issues, with being plugged in it would still power up. Maybe trouble with the usb-c port or something else? Any ideas?

(06-03-2024, 01:43 PM)tllim Wrote:

(06-02-2024, 04:11 PM)angeloweb Wrote: My Pinetab2 does not appear to be accepting power. It worked for months, then, after being untouched (while plugged in) for a couple of weeks, it wouldn't work right. Even with power plugged in the power-port, won't start.

Shortly before the battery totally drained, it would try to power on for a couple of seconds, then turn off.

Tried multiple cables & charging devices. I figure that even if the battery is having issues, with being plugged in it would still power up. Maybe trouble with the usb-c port or something else? Any ideas?

Using accompanied UART dongle and check whether their is console message.