+- PINE64 (https://forum.pine64.org)
+-- Forum: Quartz64 (https://forum.pine64.org/forumdisplay.php?fid=166)
+--- Forum: General Discussion on Quartz64 (https://forum.pine64.org/forumdisplay.php?fid=167)
+--- Thread: can't get quartz64-A working (/showthread.php?tid=18126)
Pages:
1
2
RE: can't get quartz64-A working - balbes150 - 04-19-2023
use images from this theme. official images are now being assembled from a broken build system and will have problems.
https://forum.pine64.org/showthread.php?tid=16312
In the photo with jumpers - there is no important jumper on the connector that is closer to the edge of the board (it is signed ON/OFF_BATT ). Install a jumper on it (the contacts must be closed.
RE: can't get quartz64-A working - jyoung - 04-20-2023
(04-19-2023, 11:44 PM)balbes150 Wrote: use images from this theme. official images are now being assembled from a broken build system and will have problems.
https://forum.pine64.org/showthread.php?tid=16312
In the photo with jumpers - there is no important jumper on the connector that is closer to the edge of the board (it is signed ON/OFF_BATT ). Install a jumper on it (the contacts must be closed.
Just to double check, we want to jump (connect) the two pins on board that are closer to the edge?
RE: can't get quartz64-A working - balbes150 - 04-21-2023
(04-20-2023, 01:31 PM)jyoung Wrote:(04-19-2023, 11:44 PM)balbes150 Wrote: use images from this theme. official images are now being assembled from a broken build system and will have problems.
https://forum.pine64.org/showthread.php?tid=16312
In the photo with jumpers - there is no important jumper on the connector that is closer to the edge of the board (it is signed ON/OFF_BATT ). Install a jumper on it (the contacts must be closed.
Just to double check, we want to jump (connect) the two pins on board that are closer to the edge?
Yes
RE: can't get quartz64-A working - jyoung - 04-29-2023
(04-21-2023, 12:23 AM)balbes150 Wrote:(04-20-2023, 01:31 PM)jyoung Wrote:(04-19-2023, 11:44 PM)balbes150 Wrote: use images from this theme. official images are now being assembled from a broken build system and will have problems.
https://forum.pine64.org/showthread.php?tid=16312
In the photo with jumpers - there is no important jumper on the connector that is closer to the edge of the board (it is signed ON/OFF_BATT ). Install a jumper on it (the contacts must be closed.
Just to double check, we want to jump (connect) the two pins on board that are closer to the edge?
Yes
Okay, that worked! Using one of the images from that thread + the jumper succeeded. In the interest of thoroughness, I tried the mainline Armbian image recommended for quartz64a, and that did not work. As you indicated, it looks like the mainline image is broken, unfortunately. Also in the interest of thoroughness, I tried writing the SD card with dd, and that did work.
I'm marking this thread as "solved", thanks all for helping!
RE: can't get quartz64-A working - diederik - 04-29-2023
(04-19-2023, 09:30 PM)jyoung Wrote: Here is an image of the jumpers, and of the uart pins attached to the appropriate gpio pin.
If you don't get output via UART, try switching the white and green lines.
Mine is black-white-purple and the colors don't necessary mean much. (Black is often GND though)