+- PINE64 (https://forum.pine64.org)
+-- Forum: PINE A64(+) (https://forum.pine64.org/forumdisplay.php?fid=4)
+--- Forum: General Discussion on PINE A64(+) (https://forum.pine64.org/forumdisplay.php?fid=3)
+--- Thread: Success story - Debian + ZWave (/showthread.php?tid=870)
Success story - Debian + ZWave - eljatul - 05-01-2016
Last week I received my Pine64 with 2GB RAM. My journey has been very smooth with this product. I installed Debian following the instructions on the site. Installation was surprisingly easy with zero problems. I then ported my application that I built for Raspberry Pi and again I had no trouble finding all dependencies and compiling my application (C++). Another nice experience.
I then connected my Z-Wave USB Z-Stick, tested my iOS app, my sensors, etc. and again everything worked fine in the first shot.
A couple of hours after I opened the package, I have everything running on the new Pine64. My home-grown home automation solution is now powered by Pine64.
Good job and thanks so much to everyone involved in the hardware and software development of this product. The acrylic case looks as good as the one on the site. Yay!
RE: Success story - Debian + ZWave - vinodmenon80 - 07-13-2016
(05-01-2016, 03:26 AM)eljatul Wrote: Last week I received my Pine64 with 2GB RAM. My journey has been very smooth with this product. I installed Debian following the instructions on the site. Installation was surprisingly easy with zero problems. I then ported my application that I built for Raspberry Pi and again I had no trouble finding all dependencies and compiling my application (C++). Another nice experience.
I then connected my Z-Wave USB Z-Stick, tested my iOS app, my sensors, etc. and again everything worked fine in the first shot.
A couple of hours after I opened the package, I have everything running on the new Pine64. My home-grown home automation solution is now powered by Pine64.
Good job and thanks so much to everyone involved in the hardware and software development of this product. The acrylic case looks as good as the one on the site. Yay!
Hey Mate,
I want to know what is the zwave and what practical applications can I perform with it?
RE: Success story - Debian + ZWave - martinayotte - 07-14-2016
ZWave is an RF Mesh protocol used by switches/wall-plugs manufacturers such as Leviton or GE.
With a USB Z-Stick, you can control your switches or plugs remotely from the PineA64 using OpenZWave library and Domoticz application.
RE: Success story - Debian + ZWave - mdsutton - 07-18-2016
(05-01-2016, 03:26 AM)eljatul Wrote: Last week I received my Pine64 with 2GB RAM. My journey has been very smooth with this product. I installed Debian following the instructions on the site. Installation was surprisingly easy with zero problems. I then ported my application that I built for Raspberry Pi and again I had no trouble finding all dependencies and compiling my application (C++). Another nice experience.
I then connected my Z-Wave USB Z-Stick, tested my iOS app, my sensors, etc. and again everything worked fine in the first shot.
A couple of hours after I opened the package, I have everything running on the new Pine64. My home-grown home automation solution is now powered by Pine64.
Good job and thanks so much to everyone involved in the hardware and software development of this product. The acrylic case looks as good as the one on the site. Yay!
Are you sharing this application? PLEASE!!
Congrats, I am still waiting on my enclosure and Z-Wave Module, but would love to be ready to set it up.
Martin
RE: Success story - Debian + ZWave - eljatul - 07-18-2016
(07-18-2016, 08:51 AM)mdsutton Wrote:(05-01-2016, 03:26 AM)eljatul Wrote: Last week I received my Pine64 with 2GB RAM. My journey has been very smooth with this product. I installed Debian following the instructions on the site. Installation was surprisingly easy with zero problems. I then ported my application that I built for Raspberry Pi and again I had no trouble finding all dependencies and compiling my application (C++). Another nice experience.
I then connected my Z-Wave USB Z-Stick, tested my iOS app, my sensors, etc. and again everything worked fine in the first shot.
A couple of hours after I opened the package, I have everything running on the new Pine64. My home-grown home automation solution is now powered by Pine64.
Good job and thanks so much to everyone involved in the hardware and software development of this product. The acrylic case looks as good as the one on the site. Yay!
Are you sharing this application? PLEASE!!
Congrats, I am still waiting on my enclosure and Z-Wave Module, but would love to be ready to set it up.
Martin
My home grown app is not ready to be shared yet. Meanwhile, you can use https://domoticz.com/ (c++ based) or http://www.openhab.org/ (Java based). Both are very popular and good options.