+- PINE64 (https://forum.pine64.org)
+-- Forum: ROCKPRO64 (https://forum.pine64.org/forumdisplay.php?fid=98)
+--- Forum: RockPro64 Hardware and Accessories (https://forum.pine64.org/forumdisplay.php?fid=102)
+--- Thread: Rockpro death: USB3 does not supply power for a 2.5 HDD (/showthread.php?tid=6938)
Rockpro death: USB3 does not supply power for a 2.5 HDD - zillevdr - 12-06-2018
I had a 2.5 HDD on the USB3 connector without a separate power supply. It worked any weeks. Then the rockpro dies during work on it. The Kernel can't find the filesystem. After then boot hangs on initilize the USB stack.
Code:
[ 1.352012] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[ 1.352917] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 3
[ 1.353925] xhci-hcd xhci-hcd.8.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02030010
[ 1.354941] xhci-hcd xhci-hcd.8.auto: irq 226, io mem 0xfe800000
[ 1.355797] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.356557] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.357372] usb usb3: Product: xHCI Host Controller
[ 1.357931] usb usb3: Manufacturer: Linux 4.4.143 xhci-hcd
[ 1.358543] usb usb3: SerialNumber: xhci-hcd.8.auto
[ 1.359676] hub 3-0:1.0: USB hub found
[ 1.360143] hub 3-0:1.0: 1 port detected
[ 1.360907] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[ 1.361702] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 4
[ 1.362613] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.363622] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.364394] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.365206] usb usb4: Product: xHCI Host Controller
[ 1.371283] usb usb4: Manufacturer: Linux 4.4.143 xhci-hcd
[ 1.377381] usb usb4: SerialNumber: xhci-hcd.8.auto
[ 1.383998] hub 4-0:1.0: USB hub found
[ 1.389876] hub 4-0:1.0: 1 port detected
[ 1.397017] xhci-hcd xhci-hcd.8.auto: remove, state 1
[ 1.402020] usb usb4: USB disconnect, device number 1
[ 1.427810] xhci-hcd xhci-hcd.8.auto: Host not halted after 16000 microseconds.
[ 1.432979] xhci-hcd xhci-hcd.8.auto: Host controller not halted, aborting reset.
[ 1.438125] xhci-hcd xhci-hcd.8.auto: USB bus 4 deregistered
[ 1.443179] xhci-hcd xhci-hcd.8.auto: remove, state 1
[ 1.447953] usb usb3: USB disconnect, device number 1
[ 1.453175] xhci-hcd xhci-hcd.8.auto: USB bus 3 deregistered
[ 1.464310] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[ 1.470741] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 3
[ 1.477125] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02030010
[ 1.483458] xhci-hcd xhci-hcd.9.auto: irq 227, io mem 0xfe900000
[ 1.487011] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.490328] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.493644] usb usb3: Product: xHCI Host Controller
[ 1.496725] usb usb3: Manufacturer: Linux 4.4.143 xhci-hcd
[ 1.499868] usb usb3: SerialNumber: xhci-hcd.9.auto
@I'am afraid the board is broken. Any ideas what I can do?