(09-24-2018, 09:26 PM)jgpacc Wrote: I have been running a OMV on a HC1, XU4 and now Rock64.  I decided to do performance comparisons.  This then exposed my instability issue with Rock64.  The HC1 gave 110 MB/s write speed.  The XU4 only did 70 MB/s.  The Rock64 might be the star I thought but it only did about 80 MB/s before it crashed.  This now is the problem.

I try coping about 10 GBs from W10 to the Rock64 via ethernet and it fails every time at around 6 GBs. The box crashes and must be power cycled.  There is no message in the OMV log.  Smaller copies work and if I connect my USB 3.0 attached HDD to the USB 2 port the copy works but at 30 MB/s.

I have tried a HDD, a SSD and a M.2 SSD in a M.2 to USB enclosure. All 3 fail approximately the same. Makes me think the load is crashing something.  
One error in the log I see occasionally is something like  Fatal  Watchdog not found.  
I am running OMV 4.1.11  Linux version 4.4.132 on the eMMC.  I have the correct power supply.

Anyone have any ideas on this problems?  What other testing could I do to trap some meaningful error messages? 
Thanks
Joep

(09-25-2018, 11:47 AM)jgpacc Wrote: Thanks for your response.  I tried the image you suggested but that wont even boot.  I get what I would call stack dumps to the terminal.  I can catch a few lines here and there talking about stack loop lockup bla bla CPU 3.
Stops for 90 seconds and starts again.  I tried it on eMMC and SD card.

Going to see if I can reinstall the image I had working.  Maybe the board gave up

(09-25-2018, 12:43 PM)Trash_Can_Man Wrote:

(09-25-2018, 11:47 AM)jgpacc Wrote: Thanks for your response.  I tried the image you suggested but that wont even boot.  I get what I would call stack dumps to the terminal.  I can catch a few lines here and there talking about stack loop lockup bla bla CPU 3.
Stops for 90 seconds and starts again.  I tried it on eMMC and SD card.

Going to see if I can reinstall the image I had working.  Maybe the board gave up

Are you sure you downloaded the rock64 image? because it worked for me perfectly, what program do you use to write to SD card? i usually use etcher and works wonder, any other gives me mixed results but etcher works for me all the time...

(09-25-2018, 05:43 PM)jgpacc Wrote:

(09-25-2018, 12:43 PM)Trash_Can_Man Wrote:

(09-25-2018, 11:47 AM)jgpacc Wrote: Thanks for your response.  I tried the image you suggested but that wont even boot.  I get what I would call stack dumps to the terminal.  I can catch a few lines here and there talking about stack loop lockup bla bla CPU 3.
Stops for 90 seconds and starts again.  I tried it on eMMC and SD card.

Going to see if I can reinstall the image I had working.  Maybe the board gave up

Are you sure you downloaded the rock64 image? because it worked for me perfectly, what program do you use to write to SD card? i usually use etcher and works wonder, any other gives me mixed results but etcher works for me all the time...

Yes I am using OMV_4_Rock64.  But I gave up on Etcher a while ago because I keep getting that "Couldn't clean the drive, Command Failed: diskpart /s"   So I use DiskFormatter and Win32diskimager
I

(09-25-2018, 07:36 PM)Trash_Can_Man Wrote:

(09-25-2018, 05:43 PM)jgpacc Wrote:

(09-25-2018, 12:43 PM)Trash_Can_Man Wrote:

(09-25-2018, 11:47 AM)jgpacc Wrote: Thanks for your response.  I tried the image you suggested but that wont even boot.  I get what I would call stack dumps to the terminal.  I can catch a few lines here and there talking about stack loop lockup bla bla CPU 3.
Stops for 90 seconds and starts again.  I tried it on eMMC and SD card.

Going to see if I can reinstall the image I had working.  Maybe the board gave up

Are you sure you downloaded the rock64 image? because it worked for me perfectly, what program do you use to write to SD card? i usually use etcher and works wonder, any other gives me mixed results but etcher works for me all the time...

Yes I am using OMV_4_Rock64.  But I gave up on Etcher a while ago because I keep getting that "Couldn't clean the drive, Command Failed: diskpart /s"   So I use DiskFormatter and Win32diskimager
I

Well anyway if your method works with the same image i linked and it boots and all but you have instability IMO the problem is somewhere else...your rock64 have at the very least a heatsink? your enclosures/adapters have UAS enabled? did you try to disable it? if you have tried all this im out of ideas...

(09-26-2018, 02:08 PM)jgpacc Wrote:

(09-25-2018, 07:36 PM)Trash_Can_Man Wrote:

(09-25-2018, 05:43 PM)jgpacc Wrote:

(09-25-2018, 12:43 PM)Trash_Can_Man Wrote:

(09-25-2018, 11:47 AM)jgpacc Wrote: Thanks for your response.  I tried the image you suggested but that wont even boot.  I get what I would call stack dumps to the terminal.  I can catch a few lines here and there talking about stack loop lockup bla bla CPU 3.
Stops for 90 seconds and starts again.  I tried it on eMMC and SD card.

Going to see if I can reinstall the image I had working.  Maybe the board gave up

Are you sure you downloaded the rock64 image? because it worked for me perfectly, what program do you use to write to SD card? i usually use etcher and works wonder, any other gives me mixed results but etcher works for me all the time...

Yes I am using OMV_4_Rock64.  But I gave up on Etcher a while ago because I keep getting that "Couldn't clean the drive, Command Failed: diskpart /s"   So I use DiskFormatter and Win32diskimager
I

Well anyway if your method works with the same image i linked and it boots and all but you have instability IMO the problem is somewhere else...your rock64 have at the very least a heatsink? your enclosures/adapters have UAS enabled? did you try to disable it? if you have tried all this im out of ideas...

I am beginning to think something more fundamental is going on.  I can not boot with the link you gave me.  It just dumps every 90 seconds.  I installed my original  strech-openmediavault-rock64-0.7.8-1061-arm64 from the wiki.  it boots and runs for a while than crash.  I did get some messages in the log that looked significat.  Looking for modules on the emmc drive it could not find.  But funny they were there in the prior boot.  So maybe the eMMC is bad, but it does the same on SD card.  Maybe the board is just bad.  

I don't know how to disable UAS but I will look around.  I will try that over the next few days.
Thanks for your help.

(09-26-2018, 04:01 PM)Trash_Can_Man Wrote:

(09-26-2018, 02:08 PM)jgpacc Wrote:

(09-25-2018, 07:36 PM)Trash_Can_Man Wrote:

(09-25-2018, 05:43 PM)jgpacc Wrote:

(09-25-2018, 12:43 PM)Trash_Can_Man Wrote: Are you sure you downloaded the rock64 image? because it worked for me perfectly, what program do you use to write to SD card? i usually use etcher and works wonder, any other gives me mixed results but etcher works for me all the time...

Yes I am using OMV_4_Rock64.  But I gave up on Etcher a while ago because I keep getting that "Couldn't clean the drive, Command Failed: diskpart /s"   So I use DiskFormatter and Win32diskimager
I

Well anyway if your method works with the same image i linked and it boots and all but you have instability IMO the problem is somewhere else...your rock64 have at the very least a heatsink? your enclosures/adapters have UAS enabled? did you try to disable it? if you have tried all this im out of ideas...

I am beginning to think something more fundamental is going on.  I can not boot with the link you gave me.  It just dumps every 90 seconds.  I installed my original  strech-openmediavault-rock64-0.7.8-1061-arm64 from the wiki.  it boots and runs for a while than crash.  I did get some messages in the log that looked significat.  Looking for modules on the emmc drive it could not find.  But funny they were there in the prior boot.  So maybe the eMMC is bad, but it does the same on SD card.  Maybe the board is just bad.  

I don't know how to disable UAS but I will look around.  I will try that over the next few days.
Thanks for your help.

Anyway UAS affects external drives only, not EMMC/SD, start looking at that and give another chance to Etcher, maybe...and again, do you have installed a heatsink? made a real difference on my board with stability...anyway, keep us updated of your findings...