Android 7.1 (SOPINE) - Printable Version

Code:
U-Boot 2014.07 (Jul 18 2017 - 16:19:17) Allwinner Technology 



uboot commit : 13dcbb66e9d12eea804ab8a35e29ecdb3025967c

 

normal mode: with secure monitor

rsb_send_initseq: rsb clk 400Khz -> 3Mhz

[      0.380]pmbus:   ready

[SCP] :wait arisc ready....

[SCP] :arisc version: [sun8iw5_v0.03.00-227-gcec3a2b]

[SCP] :sunxi-arisc driver v1.10 startup ok

pmu type = 0x11

[      0.399]PMU: AXP81X

[      0.399]PMU: read AXP81X 84H=0xf2

[      0.401]PMU: write AXP81X 84H=0xf6

[      0.404]PMU: AXP81X found

factory

axp end

run key detect

no key found

no uart input

DRAM:  2 GiB

fdt addr0: 0xb6e78578

fdt addr1: 0xb6e8b1f8

Relocation Offset is: 75ede000

In:    serial

Out:   serial

Err:   serial

gic: sec monitor mode

[cpu1]secondary entry

[      0.508]power on secondary cpu

set power on vol to default

[      0.514]flash init start

[cpu1]dcdc1_vol = 3300, onoff=1

workmode = 0,storage type = 1

[cpu1]dcdc6_vol = 1100, onoff=1

[      0.524]MMC:        0

[cpu1]aldo1_vol = 2800, onoff=0

[      0.529]mmc init start to delay

[cpu1]aldo2_vol = 1800, onoff=1

[cpu1]aldo3_vol = 3000, onoff=1

[cpu1]dldo1_vol = 3300, onoff=0

[cpu1]dldo2_vol = 3300, onoff=0

[cpu1]dldo3_vol = 2800, onoff=0

[cpu1]dldo4_vol = 3300, onoff=1

[cpu1]eldo1_vol = 1800, onoff=1

[cpu1]eldo2_vol = 1800, onoff=0

[cpu1]eldo3_vol = 1800, onoff=0

[cpu1]fldo1_vol = 1200, onoff=0

[cpu1]fldo2_vol = 1100, onoff=1

[cpu1]gpio0_vol = 3100, onoff=0

[cpu1]find power_sply to end

[cpu1]dcin exist

[cpu1]no battery exist

[cpu1]on cpu2

[cpu1]on end

[cpu2]third entry

[      0.578]start

[cpu1]drv_disp_init

[cpu2]bmp file buffer: 0x47400000, bmp_info.buffer: 46400000

[cpu2]kill cpu 2

[cpu1]init_clocks: finish init_clocks.

[cpu1]fail to get clk for lcd1

[cpu1]fail to get clk for lcd1

[cpu1]clk_set parent tcon1 fail

[cpu1]clk_set parent pll_mipi fail

[cpu1]pwm_request:pwm number = 1

[cpu1]pwm_request: reg = 0x1f03800. pwm = 16.

[cpu1]request pwm success, pwm = 16.

[cpu1]enable power vcc-hdmi-33, ret=0

[cpu1]drv_disp_init finish

[cpu1]Hekang Debug get partno failed!

[cpu1]** Bad device specification sunxi_flash -1 **

[cpu1]load file(hdmi.txt) error 

[cpu1]boot_disp.output_disp=0

[cpu1]boot_disp.output_type=1

[cpu1]boot_disp.output_mode=4

[cpu1]fetch script data boot_disp.auto_hpd fail

[      1.036]mmc init end to delay

[cpu1]disp0 device type(1) enable

[mmc]: mmc driver ver 2016-03-31 15:50:00

[cpu1]enable