+- PINE64 (https://forum.pine64.org)
+-- Forum: PinePhone (https://forum.pine64.org/forumdisplay.php?fid=120)
+--- Forum: PinePhone Hardware (https://forum.pine64.org/forumdisplay.php?fid=122)
+--- Thread: FOSS fw problem - PinePhonePro, EG25 modem (/showthread.php?tid=19656)
FOSS fw problem - PinePhonePro, EG25 modem - dukla2000 - 01-31-2025
OK, so I have had an older PinePhonePro (mini SIM rather than micro SIM) for a while. I had flashed Biktorg's fw to it and used to be able to chat to the modem fine. A while back I had a problem 1 night setting a wakeup call (can't remember, power fail, think trying to flash 0.8.0) and since then I cant SMS the modem. I have tried everything I can think of, flashing back to stock, trying fwupd to flash, pmOS, arch, mobian, 30.006, 01.003 ADSP firmware, ...
So as I write this I have my PPP which has a "Frankenstein" firmware (it seems half FOSS but with stock artefacts) and my old PP in front of me which is FOSS and behaves like I expect.
The basic problem that is the subject of this thread - I can't send SMS to the modem:
Code:
$ cat sms.txt | sxmo_modemsendsms.sh +223344556677 -
12:41:25 sxmo_modemsendsms.sh: Couldn't send text message (error: couldn't send the SMS: 'GDBus.Error:org.freedesktop.ModemManager1.Error.Core.Connected: No AT port available to run command')
Couldn't send text message (error: couldn't send the SMS: 'GDBus.Error:org.freedesktop.ModemManager1.Error.Core.Connected: No AT port available to run command')The system log during boot - note the serial number is "community_fw":
Code:
[ 34.237819] usb 1-1: new high-speed USB device number 3 using ehci-platform
[ 34.368702] usb 1-1: New USB device found, idVendor=2c7c, idProduct=0125, bcdDevice= 3.18
[ 34.368737] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 34.368747] usb 1-1: Product: LTE Module
[ 34.368755] usb 1-1: Manufacturer: Quectel, Incorporated
[ 34.368764] usb 1-1: SerialNumber: community_fw
[ 34.441830] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 34.442645] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 34.443151] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
[ 34.443494] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB3For cross reference on my PP the system log has the same info:
Code:
[ 52.475036] usb 2-1: new high-speed USB device number 3 using ehci-platform
[ 52.636611] usb 2-1: New USB device found, idVendor=2c7c, idProduct=0125, bcdDevice= 3.18
[ 52.640986] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 52.641138] usb 2-1: Product: LTE Module
[ 52.641198] usb 2-1: Manufacturer: Quectel, Incorporated
[ 52.641232] usb 2-1: SerialNumber: community_fw
[ 52.717965] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 52.723460] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 52.737674] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB2
[ 52.742115] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB3The reason for my "Frankenstein" use is that the differences start showing in the journal - my PPP has
Code:
[Jan 31 12:27:05] daemon eg25-manager: ** Message: 12:27:05.087: Successfully sent command: AT+QGMR
...
[Jan 31 12:27:05] daemon eg25-manager: ** Message: 12:27:05.113: Response: [EG25GGBR07A08M2G_01.003.00.000\r\n\r\nOK]Whereas the PP has
Code:
[Jan 01 01:01:30] daemon eg25-manager: ** Message: 01:01:30.626: Successfully sent command: AT+QGMR
...
[Jan 01 01:01:30] daemon eg25-manager: ** Message: 01:01:30.645: Response: [0.7.4\r\n\r\nOK]So it appears my most recent attempt to flash the modem failed, but the log is (flashing 0.7.4 FWIW):
Code:
# ./flashall
Sending AT+QFASTBOOT...
OKAY [ 0.002s]
Finished. Total time: 0.002s
Warning: skip copying aboot image avb footer (aboot partition size: 0, aboot image size: 286476).
Sending 'aboot' (279 KB) OKAY [ 0.013s]
Writing 'aboot' OKAY [ 0.131s]
Finished. Total time: 0.166s
Rebooting OKAY [ 0.004s]
Finished. Total time: 0.055s
< waiting for any device >
OKAY [ 0.002s]
Finished. Total time: 0.002s
Sending 'boot' (4600 KB) OKAY [ 0.149s]
Writing 'boot' OKAY [ 1.793s]
Finished. Total time: 1.955s
Sending 'recovery' (4600 KB) OKAY [ 0.148s]
Writing 'recovery' OKAY [ 1.795s]
Finished. Total time: 1.963s
Warning: skip copying system image avb footer (system partition size: 0, system image size: 28311552).
Sending 'system' (27648 KB) OKAY [ 0.879s]
Writing 'system' OKAY [ 11.942s]
Finished. Total time: 12.844s
Warning: skip copying recoveryfs image avb footer (recoveryfs partition size: 0, recoveryfs image size: 13369344).
Sending 'recoveryfs' (13056 KB) OKAY [ 0.417s]
Writing 'recoveryfs' OKAY [ 4.949s]
Finished. Total time: 5.391s
Rebooting OKAY [ 0.004s]
Finished. Total time: 0.055s
Done!Any thoughts welcome - my only hope is to keep trying to flash 0.7.4 and hope it works!
RE: FOSS fw problem - PinePhonePro, EG25 modem - zetabeta - 01-31-2025
may not be your case totally, but look it anyway.
https://forum.pine64.org/showthread.php?tid=19421&highlight=fix+modem+partition
RE: FOSS fw problem - PinePhonePro, EG25 modem - dukla2000 - 01-31-2025
(01-31-2025, 01:24 PM)zetabeta Wrote: may not be your case totally, but look it anyway.
https://forum.pine64.org/showthread.php?tid=19421&highlight=fix+modem+partition
Thanks - some similarities but not completely.
I should have added in my first post that in fact I could not send or receive any SMS, couldn't make or receive any call and although the data APN would attach I couldn't get any data via LTE.
I do have some good progress though:
- I deleted all the downloaded stuff I had and started with a fresh download of the FOSS firmware and checked all the sha512sums. I also downloaded a fresh copy of the 30.200 ADSP. I could flash them happily and it made no difference. I even tried ./flashall twice in a row followed by the HLOS twice, nada.
- I meticulously followed the Going back to stock instructions (rather than ./flashstock) and I do seem to have a fully functioning EG25GGBR07A08M2G_30.006.30.006 - SMS, calls and data are all functioning.
- I tried to use fwupdmgr on pmOS and it wont do any up (or down) grades
Next to try is to flash Biktorgj's 0.7.4 again - I want the SMS interface (for alarms etc) but am a bit nervous about why I patently failed to do it properly before! Watch this space
OK, so tried a FOSS flash again, have a Frankenstein setup again except SMS & calls seem to work.
First the log of my attempt to flash in the same order as the recovery instructions above (i.e. aboot last)
Code:
$ lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 18d1:d00d Google Inc. Xiaomi Mi/Redmi 2 (fastboot)
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
...
fastboot flash system rootfs-mdm9607.ubi-mdm9607.ubi
Warning: skip copying system image avb footer (system partition size: 0, system image size: 28311552).
Sending 'system' (27648 KB) OKAY [ 1.429s]
Writing 'system' OKAY [ 10.086s]
Finished. Total time: 11.540s
[csn@PPP modem]$ fastboot flash recoveryfs recoveryfs.ubi
Warning: skip copying recoveryfs image avb footer (recoveryfs partition size: 0, recoveryfs image size: 13369344).
Sending 'recoveryfs' (13056 KB) OKAY [ 0.682s]
Writing 'recoveryfs' OKAY [ 4.441s]
Finished. Total time: 5.149s
[csn@PPP modem]$ fastboot flash:raw boot boot-mdm9607.img
Sending 'boot' (4600 KB) OKAY [ 0.148s]
Writing 'boot' OKAY [ 1.580s]
Finished. Total time: 1.944s
[csn@PPP modem]$ fastboot flash:raw recovery boot-mdm9607.img
Sending 'recovery' (4600 KB) OKAY [ 0.149s]
Writing 'recovery' OKAY [ 1.582s]
Finished. Total time: 1.746s
[csn@PPP modem]$ fastboot flash aboot appsboot.mbn
Warning: skip copying aboot image avb footer (aboot partition size: 0, aboot image size: 286476).
Sending 'aboot' (279 KB) OKAY [ 0.028s]
Writing 'aboot' OKAY [ 0.136s]
Finished. Total time: 0.188s
[csn@PPP modem]$ fastboot rebootSystem log says community_fw
Code:
[ 37.845272] usb 1-1: new high-speed USB device number 3 using ehci-platform
[ 37.992120] usb 1-1: New USB device found, idVendor=2c7c, idProduct=0125, bcdDevice= 3.18
[ 37.992164] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 37.992183] usb 1-1: Product: LTE Module
[ 37.992198] usb 1-1: Manufacturer: Quectel, Incorporated
[ 37.992213] usb 1-1: SerialNumber: community_fwBut it still thinks it is stock and wont play nicely with the SMS interface.
Code:
$ echo 'AT+QGMR' | sudo atinout - /dev/ttyUSB2 -
EG25GGBR07A08M2G_30.006.30.006
OK
[csn@PPP ~]$ ./sendsms.sh +223344556677
20:58:48 sxmo_modemsendsms.sh: Couldn't send text message (error: couldn't send the SMS: 'GDBus.Error:org.freedesktop.ModemManager1.Error.Message.Unknown: Unknown message error: 350')
Couldn't send text message (error: couldn't send the SMS: 'GDBus.Error:org.freedesktop.ModemManager1.Error.Message.Unknown: Unknown message error: 350')Guess I will flash properly back to stock and stick with that for now
RE: FOSS fw problem - PinePhonePro, EG25 modem - biketool - 02-02-2025
I HAVE to make a copypasta for the PPp modem issue, someone PLEASE put this on the wikis!!!
https://themodemdistro.com/efs_recovery
now your issue is not the usual softbrick PPp modem issue but surf the Biktorg website and is has great documentation for exactly this type of stuff.
I wish it were mentioned in the main git, Pine64, or mobian wiki.
for your issue look at https://themodemdistro.com/docs SMS Interface header
RE: FOSS fw problem - PinePhonePro, EG25 modem - dukla2000 - 02-04-2025
(02-02-2025, 11:31 AM)biketool Wrote: I HAVE to make a copypasta for the PPp modem issue, someone PLEASE put this on the wikis!!!
https://themodemdistro.com/efs_recovery
now your issue is not the usual softbrick PPp modem issue but surf the Biktorg website and is has great documentation for exactly this type of stuff.
I wish it were mentioned in the main git, Pine64, or mobian wiki.
...
The Pine64 wiki does link to Biktorgj's github (which in turn links to themodemdistro website).
(02-02-2025, 11:31 AM)biketool Wrote: ...
for your issue look at https://themodemdistro.com/docs SMS Interface header
I think I have read most of the github issues and documentation. My issue, as per the first bit I posted in code in my first post, is I can't send an SMS to my modem. And (my conclusion) is because I am unable to properly and completely flash the FOSS firmware. ./flashall runs just fine, except I then have a mix up - it is not FOSS to the extent I can send the SMS.
RE: FOSS fw problem - PinePhonePro, EG25 modem - biketool - 02-05-2025
(02-04-2025, 02:53 PM)dukla2000 Wrote:(02-02-2025, 11:31 AM)biketool Wrote: I HAVE to make a copypasta for the PPp modem issue, someone PLEASE put this on the wikis!!!
https://themodemdistro.com/efs_recovery
now your issue is not the usual softbrick PPp modem issue but surf the Biktorg website and is has great documentation for exactly this type of stuff.
I wish it were mentioned in the main git, Pine64, or mobian wiki.
...
The Pine64 wiki does link to Biktorgj's github (which in turn links to themodemdistro website).
I found the website by digging through bug reports in the git, it is not easy to find at all, which is unfortunate as it is a well designed website full of useful modem related fixes and tweaks. I do see that there is now a link to the website at the bottom of the git page, he claims to be terrible with documenting writes amazing documentation website for his modem firmware and