(07-09-2023, 01:33 AM)vusra Wrote: a) no.
b) why?
c) yes. remove u-boot first utilizing  sudo dd if=/dev/zero of=/dev/[DEVICE] bs=8k seek=1 count=4 

Code:

# Startup order conflicts

The Allwinner SoC used in the Pinephone (A64) will always prefer starting
the platform firmware (U-Boot) from SD card when available.

When using some pre-built distribution images, it may be desirable to neuter
the U-Boot that is baked into the image.

With the usual U-Boot setup for Allwinner, the easiest way to strip U-Boot
from an eMMC or SD image is by running the following command, taking care
to replace `[DEVICE]` with the device for the storage device.

```
$ sudo dd if=/dev/zero of=/dev/[DEVICE] bs=8k seek=1 count=4
```

When running the command on the Pinephone (A64), *usually* the block device
for the SD card is `mmcblk0`, and the block device for the eMMC is `mmcblk2`.
You can use `lsblk` to look at the block devices available.

> **NOTE**: Make sure the operating system image has a baked-in U-Boot
> install before issuing the command, and that you are targeting the right
> storage device.
>
> Some distributions target UEFI boot, and use GPT. Issuing this command
> **will break the partition table**.

Finally, on distributions shipping U-Boot, it is prudent to disable the
package that provides the automatic upgrade facilities.

- For Manjaro and Arch Linux, the package is called `uboot-pinephone`.


## Additional features

The phone can be started in *USB Mass Storage* mode by holding the *volume up*

d) not needed.  but  dd backup for safety before upgrade. tow boot is small code written to start of eMMC.


Hello, as someone new this, I'm also having a bit of a confusing time with this. 

The installation guide (https://tow-boot.org/devices/pine64-pinephoneA64.html) lists an image file (mmcboot.installer.img) that needs to be written to an sd card (I assume) from my pc onto the sd card. I looked for the image file on the listed github link at right--where is this file? 

After getting the image file and writing it to the sd card using dd, do I just take and load the sd card into the pinephone and start it up? Will there be any prompts to install Tow-Boot to the emmc module? Would this same installer allow one to wipe the memory of the emmc or is this a separate step?

I don't particularly care about what is on the pinephone emmc module, in fact, I'd prefer to wipe it clean so I can install, in this case mobian, which requres it to be loaded on the module instead of running off of the sd card directly. 

(11-21-2023, 01:05 AM)uncleanblessing Wrote: d) not needed.  but  dd backup for safety before upgrade. tow boot is small code written to start of eMMC.


Hello, as someone new this, I'm also having a bit of a confusing time with this. 

The installation guide (https://tow-boot.org/devices/pine64-pinephoneA64.html) lists an image file (mmcboot.installer.img) that needs to be written to an sd card (I assume) from my pc onto the sd card. I looked for the image file on the listed github link at right--where is this file? 

After getting the image file and writing it to the sd card using dd, do I just take and load the sd card into the pinephone and start it up? Will there be any prompts to install Tow-Boot to the emmc module? Would this same installer allow one to wipe the memory of the emmc or is this a separate step?

I don't particularly care about what is on the pinephone emmc module, in fact, I'd prefer to wipe it clean so I can install, in this case mobian, which requres it to be loaded on the module instead of running off of the sd card directly. 

(11-22-2023, 10:20 AM)aLoop100o Wrote:

(11-21-2023, 01:05 AM)uncleanblessing Wrote: d) not needed.  but  dd backup for safety before upgrade. tow boot is small code written to start of eMMC.


Hello, as someone new this, I'm also having a bit of a confusing time with this. 

The installation guide (https://tow-boot.org/devices/pine64-pinephoneA64.html) lists an image file (mmcboot.installer.img) that needs to be written to an sd card (I assume) from my pc onto the sd card. I looked for the image file on the listed github link at right--where is this file? 

After getting the image file and writing it to the sd card using dd, do I just take and load the sd card into the pinephone and start it up? Will there be any prompts to install Tow-Boot to the emmc module? Would this same installer allow one to wipe the memory of the emmc or is this a separate step?

I don't particularly care about what is on the pinephone emmc module, in fact, I'd prefer to wipe it clean so I can install, in this case mobian, which requres it to be loaded on the module instead of running off of the sd card directly. 

The image file is actually dug into the tar.xz which you need to extract first, this caught me off as well (grab pine64-pinephoneA64.tar.xz on the latest release page, as of writing: https://github.com/Tow-Boot/Tow-Boot/releases/tag/release-2022.07-006).

Yet a further problem awaits, the installation of mobian. I cannot get mobian to boot from the sd disk and I do not know why.


Do I need to use the USB-selection feature (holding volume up) of tow-boot and use an usb stick? Is the latest release simply broken?

(11-22-2023, 11:43 AM)fxc Wrote: Actually you need to hold VOLUME DOWN (aqua LED) to boot from microSD card when you use Tow-Boot.

The other mode you mean, VOLUME UP (resulting in a blue LED), is actually for writing to the eMMC or microSD card via an USB cable connected to your computer, it is called "USB Mass Storage mode". It can not be used to boot from an USB stick.