Manjaro Image - Printable Version +- PINE64 (https://forum.pine64.org) +-- Forum: Quartz64 (https://forum.pine64.org/forumdisplay.php?fid=166) +--- Forum: Linux on Quartz64 (https://forum.pine64.org/forumdisplay.php?fid=168) +--- Thread: Manjaro Image (/showthread.php?tid=14354) |
Manjaro Image - Bullet64 - 07-05-2021 Now that we have working LAN, we can link this image here https://github.com/manjaro-arm/quartz64-bsp-images/releases The image is updated weekly. With Code: pacman -Syu you can then update it. Working
Quote:If there is no battery plugged into the board, the jumper labelled "ON/OFF_BATT" must be in place. If this is set wrong, stability issues such as failures to boot will occur.Source: https://wiki.pine64.org/wiki/Quartz64#Stability.2FBoot_Issues_With_Missing_Battery_Shunt Thank you Dan! RE: Manjaro Image - zer0sig - 07-10-2021 Just received my first of 2 quartz64s, will likely try this soon. I like manjaro and have it on multiple PINE devices (the phone and PBP right now I think). RE: Manjaro Image - espen - 08-07-2021 How do I even boot this thing? I've downloaded manjaro image from gintub, flashed it with dd to an sd-card... and I get nothing. I know that hdmi doesn't work yet, but LAN port doesn't have a link either (tried turning off autonegotiation on the switch, tried 100m 100m, no luck). Tried various power/reset inputs - still no luck. SoC gets barely warm, so there is definitely something going on with an angry pixies inside RE: Manjaro Image - homerunisgood - 09-21-2021 I have flashed the latest image from manjaro for quartz github repo, and got as far as getting an output on UART, but it remains stuck while booting the kernel... I have a jumper on ON/OFF_BAT pins, and get stuck on the following: Disk: /dev/sda Size: 29.12 GiB, 31268536320 bytes, 61071360 sectors Label: gpt, identifier: 8551F660-0661-4597-8AF9-EA3B6AFC5F42 Device Start End Sectors Size Type >> Free space 2048 16383 14336 7M /dev/sda1 16384 30719 14336 7M Microsoft basic data Free space 30720 62499 31780 15.5M /dev/sda2 62500 500000 437501 213.6M EFI System /dev/sda3 500001 3291102 2791102 1.3G Linux filesystem Free space 3291136 61071326 57780191 27.6G Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00) Total: 218.346 ms INFO: Preloader serial: 2 NOTICE: BL31: v2.3():v2.3-135-gcda1658bc-dirty:xsf NOTICE: BL31: Built : 19:32:20, Jun 2 2021 INFO: GICv3 without legacyr initialized in EL3 INFO: pmu v1 is valid INFO: dfs DDReq_mhz= 1056MHz INFO: dfs DDR fsp_param[1].freq_mhz= 324MHz INFO: dfs DDR fsp_param[2].f dfs DDR fsp_param[3].freq_mhz= 780MHz INFO: Using opteed sec cpu_context! INFO: boot INFO: BL31: Initializing runtime services INFO: BL31: Initializing BL32 I/TC: I/TC: Start rockchip platform init I/TC: Rockchip release version: 1.0 I/TC: OP-TEE ve 2021 aarch64 I/TC: Initialized INFO: BL31: Preparing for E to normal world INFO: Entry point address = 0xa00000 INFO: SPSR = 0x3c9 U-Boot 2017.09 (Jun 26 2021 - 13:03:27 +0000) Model: PineRK3566 Quartz64 Board PreSerial: 2, raw, 0xfe660000 DRAM: 7.7 GiB Sysmem: init Relocation Offset: ed39f000, fdt: eb9f9fbdwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0 Bootdev(atags): mmc 0 MMC0: HS200, 200Mhz PartType: EFI No misc partition boot mode: None FIT: No boot partition No r Failed to load DTB Failed to get kernel dtb, ret=-19 io-domain: OK MMC error: The cmd index is 1, ret is -110 Card did not respondct! mmc_init: -95, time 10 ** Bad device mmc 1 ** Using default environment Model: Pine64 RK3566 Quartz64 Board rockchip_set_serialno: could not find efuse/otp device CLK: (syarm: enter 816000 KHz, init 816000 KHz, kernel 0N/A) apll 816000 KHz dpll 528000 KHz gp npll 24000 KHz vpll 24000 KHz hpll 24000 KHz ppll 100000 KHz armclk 816000 KHz aclk_bus 150000 KHz pclk_bus 5KHz aclk_top_high 300000 KHz aclk_top_low 200000 KHz hclk_top 150000 KHz pclk_top 50hclk_perimid 150000 KHz pclk_pmu 50000 KHz Net: clk_get_by_name(master_bus) failed: -22eqo failed: -22No ethernet found. Hit key to stop autoboot('CTRL+C'): 0 ## Booting FIT Image FIT: No boot partition FIT: No FIartition ANDROID: reboot reason: "(none)" optee api revision: 2.0 TEEC: Waring: Could not find security partition Not AVB images, AVB skip android_image_lot find part: boot Android image load failed Android boot failed, error -1. MMC error: The cmd index is 1, ret is -110 Card did not respond mmc0(part 0) is current device Scanning mmc 0:2... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinreading /extlinux/extlinux.conf 285 bytes read in 15 ms (18.6 Ki Manjaro ARM Retrieving file: /initramfs-linux.img reading /initramfs-linux.img 7788335 bytes read in 59 ms (125.9 MiB/s) Retrieving file: /Imareading /Image 29518336 bytes read in 187 ms (150.5 MiB/s) append: initrd=/initramfs-linux.img root=PARTUUID=d35c868c-5a33-4bae-b2f6-f0cb5b2aac3a rw earlycon=uart8250,mmio32,,1500000n8 s Retrieving file: /dtbs/rockchip/rk3566-reading /dtbs/rockchip/rk3566-quartz64-a.dtb 104865 bytes read in 28 ms (3.6 MiB/s) Fdt Ramdisk skip relocation ## Flattened Device Tree blob at 0x0a100000 Booting using the fdt blob at 0x0a100000 Using Device Tree in place at 000000000a100000, end 000000000a11c9a0 can't found rockchip,drm-logo, use rockchip,fb-logo WARNING: could not set reg FDT_ERR_BADOFFSET. failed to reserve fb-loader-logo memory Adding bank: 0x00200000 - 0x08400000 (sisize: 0xe6c00000) Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000) Total: 786.452 ms Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050] [ 0.000000] Linux verGCC) 10.2.0, GNU ld (GNU Binutils) 2.35) #1 SMP PREEMPT Fri Sep 17 12:52:46 UTC 2021 [ 0.000ne64 RK3566 Quartz64-A Board [ 0.000000] earlycon: uart8250 000] printk: bootconsole [uart8250] enabled [ 3.048209] rockchip-usb2phy fe8a0000.usb2-phy: failed to cre[ 3.067859] arm-scmi firmwarecmi: Failed. SCMI protocol 2e [ 3.496594] arm-scmi firmwarecmi: Failed. SCMI protocol 19 not active. [ 3.499908] arm-scmi firmwarecmi: Failed. SCMI protocol 17 [ 3.561017] rockchip-dw-pcie 3c0000000.pcie: invalid resour) Starting version 249.4-1-arch ---- and then nothing anymore... Am I missing something? I would expect to get a prompt after a while, or something. thx! |