PINE64
Cases and Enclosure Question - Printable Version

+- PINE64 (https://forum.pine64.org)
+-- Forum: PINE A64(+) (https://forum.pine64.org/forumdisplay.php?fid=4)
+--- Forum: Pine A64 Hardware, Accessories and POT (https://forum.pine64.org/forumdisplay.php?fid=32)
+---- Forum: Enclosures (https://forum.pine64.org/forumdisplay.php?fid=14)
+---- Thread: Cases and Enclosure Question (/showthread.php?tid=43)

Pages: 1 2 3 4 5 6 7

RE: Cases and Enclosure Question - SirLenuxx - 04-01-2016

Im searching for the specific measures of the pine 64 , every port location ( HDMI , Ethernet , ... ) , the actual shematics aren't that specific only the

measure of the hole pine 64 architecture and i need them actually to make my Case and it will be with plex so i don't wan't to make

any error . Thanks you .

RE: Cases and Enclosure Question - kyllikki - 04-02-2016

I have measured my newly arrived board and created my own drawings and 3d models.

These are all based on measuring my single board so may not be correct for other peoples boards and I obviously have no tolerance information but perhaps they will be useful to someone until the real drawings are released.

And before anyone says anything my board was 127 x 79.5mm as measured with my calipers and not the 127 x 79mm that has previously been mentioned

files can be found https://github.com/kyllikki/designs/tree/master/Pine64_Board

RE: Cases and Enclosure Question - Tarjei85 - 04-03-2016

(04-02-2016, 05:56 PM)kyllikki Wrote: I have measured my newly arrived board and created my own drawings and 3d models.

These are all based on measuring my single board so may not be correct for other peoples boards and I obviously have no tolerance information but perhaps they will be useful to someone until the real drawings are released.

And before anyone says anything my board was 127 x 79.5mm as measured with my calipers and not the 127 x 79mm that has previously been mentioned

files can be found https://github.com/kyllikki/designs/tree/master/Pine64_Board

Thank you!!! Finally a complete drawing... perfect for finishing my casing.

RE: Cases and Enclosure Question - SirLenuxx - 04-03-2016

Thanks very much it's make a while im searching for those measure im think im not the only one ~

RE: Cases and Enclosure Question - tllim - 04-03-2016

(04-02-2016, 05:56 PM)kyllikki Wrote: I have measured my newly arrived board and created my own drawings and 3d models.

These are all based on measuring my single board so may not be correct for other peoples boards and I obviously have no tolerance information but perhaps they will be useful to someone until the real drawings are released.

And before anyone says anything my board was 127 x 79.5mm as measured with my calipers and not the 127 x 79mm that has previously been mentioned

files can be found https://github.com/kyllikki/designs/tree/master/Pine64_Board

Can I share your information on Pine64 wiki page?
... TL Lim

RE: Cases and Enclosure Question - kyllikki - 04-03-2016

(04-03-2016, 02:12 PM)tllim Wrote:
(04-02-2016, 05:56 PM)kyllikki Wrote: I have measured my newly arrived board and created my own drawings and 3d models.

These are all based on measuring my single board so may not be correct for other peoples boards and I obviously have no tolerance information but perhaps they will be useful to someone until the real drawings are released.

And before anyone says anything my board was 127 x 79.5mm as measured with my calipers and not the 127 x 79mm that has previously been mentioned

files can be found https://github.com/kyllikki/designs/tree/master/Pine64_Board

Can I share your information on Pine64 wiki page?
... TL Lim
sure, its licenced as creative commons by attribution, so as long as you credit me its fine

RE: Cases and Enclosure Question - tllim - 04-03-2016

(04-03-2016, 02:29 PM)kyllikki Wrote:
(04-03-2016, 02:12 PM)tllim Wrote:
(04-02-2016, 05:56 PM)kyllikki Wrote: I have measured my newly arrived board and created my own drawings and 3d models.

These are all based on measuring my single board so may not be correct for other peoples boards and I obviously have no tolerance information but perhaps they will be useful to someone until the real drawings are released.

And before anyone says anything my board was 127 x 79.5mm as measured with my calipers and not the 127 x 79mm that has previously been mentioned

files can be found https://github.com/kyllikki/designs/tree/master/Pine64_Board

Can I share your information on Pine64 wiki page?
... TL Lim
sure, its licenced as creative commons by attribution, so as long as you credit me its fine
thanks and will do the proper credit :-)

RE: Cases and Enclosure Question - User 563 - 04-09-2016

(04-02-2016, 05:56 PM)kyllikki Wrote: I have measured my newly arrived board and created my own drawings and 3d models.

These are all based on measuring my single board so may not be correct for other peoples boards and I obviously have no tolerance information but perhaps they will be useful to someone until the real drawings are released.

And before anyone says anything my board was 127 x 79.5mm as measured with my calipers and not the 127 x 79mm that has previously been mentioned

files can be found https://github.com/kyllikki/designs/tree/master/Pine64_Board

This is great, but can your software export or save as a real solid file, such as STEP? Using Solidworks and Fusion 360 that STL is somewhat buggy and difficult to translate to a solid model.

Glad someone took the time, though, and looking forward to designing a solid aluminum or copper case for the board sitting in front of me.

Edit: I took a different route and imported the DXF into Fusion 360 and created a solid model from the DXF sketch. I used the board sitting in front of me. I'd be happy to share if anyone wants a non-STL version, and can export as STEP, IGES, SAT or SMT, or as a .F3D file if someone wants to directly edit my extrusion parameters and edit the solid from the original.

Edit 2: I added important chip locations (for heat sinks), will probably add pinouts later. For now this works.

[Image: Tr5IsWh.jpg]