(08-08-2016, 04:30 AM)martinzheng Wrote:

(08-07-2016, 10:30 PM)dkryder Wrote: this is from DISM.log after a failed flash. the flash process had proceeded to the 30% mark successfully before issueing the error.   the dashboard reported that the SDcard was not formatted, but of course it had been. most recently by windows after the first time this message appeared. it's a good card.  any ideas?
2016-08-07 21:16:58, Error                 DISM   FFU Provider: PID=7652 While reading image data, a hash check failed. - CFfuManager::FfuLog
2016-08-07 21:16:58, Error                 DISM   FFU Provider: PID=7652 While applying the image to disk, a read failed to return all of the blocks specified in the current data descriptor. hr = 0x2dbe260b. - CFfuManager::FfuLog
2016-08-07 21:16:58, Error                 DISM   FFU Provider: PID=7652 TID=9676 onecore\base\ntsetup\opktools\dism\providers\ffuprovider\dll\ffumanager.cpp:240 - CFfuManager::Apply(hr:0x8007000e)
2016-08-07 21:16:58, Error                 DISM   FFU Provider: PID=7652 TID=9676 onecore\base\ntsetup\opktools\dism\providers\ffuprovider\dll\ffumanager.cpp:163 - CFfuManager::ApplyImage(hr:0x8007000e)
2016-08-07 21:16:58, Error                 DISM   DISM Imaging Provider: PID=7652 TID=9676 onecore\base\ntsetup\opktools\dism\providers\imagingprovider\dll\genericimagingmanager.cpp:2581 - CGenericImagingManager::InternalCmdFFUApply(hr:0x8007000e)
2016-08-07 21:16:58, Error                 DISM   DISM Imaging Provider: PID=7652 TID=9676 onecore\base\ntsetup\opktools\dism\providers\imagingprovider\dll\genericimagingmanager.cpp:535 - CGenericImagingManager::ExecuteCmdLine(hr:0x8007000e)
2016-08-07 21:16:58, Info                  DISM   DISM.EXE: Image session has been closed. Reboot required=no.
2016-08-07 21:16:58, Info                  DISM   DISM.EXE:
2016-08-07 21:16:58, Info                  DISM   DISM.EXE: <----- Ending Dism.exe session ----->
2016-08-07 21:16:58, Info                  DISM   DISM.EXE:

This is because the ffu file that you are using is broken. I think Tim would update a new image.

(08-08-2016, 07:34 AM)dkryder Wrote: the file on the pine64 site is 300MB, the file on onedrive is no longer there.

(08-08-2016, 10:28 AM)rookieone Wrote: Using an USB hub and USB2Ethernet adapter I had lying around I indeed seem to be able to have keyboard, mouse and networking!

(08-08-2016, 07:34 AM)dkryder Wrote: the file on the pine64 site is 300MB, the file on onedrive is no longer there.

(08-08-2016, 07:02 PM)Leeway213 Wrote:

(08-08-2016, 07:34 AM)dkryder Wrote: the file on the pine64 site is 300MB, the file on onedrive is no longer there.

That onedrive account has been forbidden for 24 hours because of a big mount of visit. Lim will update the ffu soon I think

(08-08-2016, 11:50 PM)dkryder Wrote:

(08-08-2016, 07:02 PM)Leeway213 Wrote:

(08-08-2016, 07:34 AM)dkryder Wrote: the file on the pine64 site is 300MB, the file on onedrive is no longer there.

That onedrive account has been forbidden for 24 hours because of a big mount of visit. Lim will update the ffu soon I think

ok. yes, i was able to download the ffu. thank you,   tllim, for putting it up. i was able to boot , however had problems with provisioning and as a result had everthing but internet working. i am using a usb hub with wireless keyboard/trackpad and hub has ethernet jack but i think microsoft keeps net access off until the device is properly provisioned. i have no ip address at this point. the hub works fine with debian so i know the hardware is ok. not sure what i can do. i'd rather not flash again.

(08-09-2016, 12:23 AM)martinzheng Wrote:

(08-08-2016, 11:50 PM)dkryder Wrote:

(08-08-2016, 07:02 PM)Leeway213 Wrote:

(08-08-2016, 07:34 AM)dkryder Wrote: the file on the pine64 site is 300MB, the file on onedrive is no longer there.

That onedrive account has been forbidden for 24 hours because of a big mount of visit. Lim will update the ffu soon I think

ok. yes, i was able to download the ffu. thank you,   tllim, for putting it up. i was able to boot , however had problems with provisioning and as a result had everthing but internet working. i am using a usb hub with wireless keyboard/trackpad and hub has ethernet jack but i think microsoft keeps net access off until the device is properly provisioned. i have no ip address at this point. the hub works fine with debian so i know the hardware is ok. not sure what i can do. i'd rather not flash again.

A hub with Ethernet? Do you know which Ethernet chip it uses? currently, IoT core can support ax88772.

(08-09-2016, 04:43 AM)Terra854 Wrote: Is it possible for the IoT Core to support the rtl8201cp and rtl8211e chips that are present in Pine A64+ so that it is able to natively support ethernet without the need for a converter.