PineTime case
#11
(01-29-2020, 09:56 AM)dejvino Wrote: Easy - drill a hole from the side of the back, pull 4 wires through,solder them in and then glue the back. That's what I did. If you have nicely colored wires, it may even look good! Big Grin

Oi, no revealing trade secrets, or what my setup looks like! :-P

I actually broke five wires out, as I break the ground line with a switch, so I can cut the power.

https://drive.google.com/file/d/12Cw_a4R...sp=sharing

https://drive.google.com/file/d/126PGyna...sp=sharing
  Reply
#12
So... has anyone found a fabric strap with a loose enough weave to integrate the SWD wires as a feature of the design ;-)

Actually I might have stumbled upon a  new idea...

I think the *smallest* number of additional conductors that needs to come out is 2, SWDIO and SWCLK? In other words there is already a ground as part of the charging pins and there is no need to share the 3v3 if your SWD programmer has its own 3v3 voltage reference?

If that's the case then I think a *very* subtle mod might be possible whilst still allowing access for an SWD programmer: drill small holes very carefully through plastic casing to reveal the chassis of both of the magnets. The holes should be just enough to allow access using pogo pin. After that all that should be needed inside the watch is to run hookup wire from the SWDIO and SWCLK to the body of each magnet and seal it all up.

Bonus marks are available for managed to solder ESD protection diodes to the hook up wires ;-)... possible I think but pretty fiddly.
PineTime: wasp-os and MicroPython, Pinebook Pro:  Debian Bullseye
  Reply
#13
Hi, I was thinking in something like this:

- https://www.digikey.com/product-detail/e...ND/2537941
- https://www.bourns.com/docs/Product-Data.../70ADF.pdf

It is little and wires can be solded to it .

What do you think?
  Reply
#14
I found this 3d printable case enclosure. Exactly what I'm looking for.
Printing it now.

https://www.thingiverse.com/thing:4172849
  Reply
#15
(05-03-2020, 01:15 AM)ahmadster Wrote: I found this 3d printable case enclosure. Exactly what I'm looking for.
Printing it now.

https://www.thingiverse.com/thing:4172849

Let us know how well this works, with pictures if possible.
  Reply
#16
I ordered a 3D print of the case and it looks good.

Unlike the model, mine came without the bridge over the button - maybe it's for the best. The button is easier to push than if it was surrounded on all sides.

The back fits snug to the body and the watch doesn't gain that much bulk. The case doesn't sit uncomfortably - there aren't sharp edges that would sink into the hand.

I don't have the original charger but just touching the pins starts the charging. All good so far.

Here are a few pics:
https://drive.google.com/file/d/1nISusI9...p=drivesdk
https://drive.google.com/file/d/1nZuVojo...p=drivesdk
https://drive.google.com/file/d/1n_lnr99...p=drivesdk
https://drive.google.com/file/d/1nKWyryW...p=drivesdk

Device: Pinebook Pro 128GB No:246 / MainOS: Manjaro ARM
Godot and Flutter - creating something can be fun with the right tools!
  Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Import charges for Pinetime CrowdOfOne 3 71 1 hour ago
Last Post: CrowdOfOne
  PineTime Software Images VMMainFrame 5 220 05-05-2020, 06:09 AM
Last Post: danielt
  PineTime smartwatch - a Linux Phone companion Luke 33 9,412 03-26-2020, 01:59 PM
Last Post: mms
  Powering PineTime yokonav 1 164 03-23-2020, 04:53 AM
Last Post: danielt
Wink Pinetime OS - Designing an UI for the Pinetime! pinejolla 2 738 03-10-2020, 03:32 PM
Last Post: pinejolla
  PineTime LTE(eSIM) version? u974615 1 382 02-25-2020, 03:24 PM
Last Post: u974615
  FOSDEM 2020 PineTime BoF bergzand 8 606 02-02-2020, 02:05 PM
Last Post: Luke
  PineTime dev kits in the store Luke 10 1,408 01-23-2020, 02:26 PM
Last Post: tamyrlin
  Use case: medicine reminder cicero 2 279 01-20-2020, 05:31 AM
Last Post: danielt
  PineTime Baseline VMMainFrame 5 958 01-15-2020, 03:56 PM
Last Post: VMMainFrame

Forum Jump:


Users browsing this thread: 1 Guest(s)