Manjaro ARM for Pinebook
#41
"Exclamation All you need to install Manjaro on the Pinebook

manjaro-arm-installer"

As mentioned by Schiff.

I tried, but failed. Two of the required dependencies are not in the distro nor are they available from the repository. That is on top of the audio issue that I cannot seem to solve.
  Reply
#42
Added Manjaro I3(Pinebook1080P) 19.04 on Wiki and Pine64 Installer
Updated Manjaro KDE (Pinebook1080P) 19.04 on Wiki and Pine64 Installer
Updated Manjaro LXQT (Pinebook1080P) 19.04 on Wiki and Pine64 Installer
  Reply
#43
(04-14-2019, 07:34 AM)unixfox Wrote: How did you install it on the eMMC? I struggle to do it, I can't find any tutorial about that.

Simple and fast solution is booting from sd and making from command line something like this:

dd if=/dev/whereversd of=/dev/whereeveremmc bs=1M

You need location on dev of your storage before.
  Reply
#44
Quote:Simple and fast solution is booting from sd and making from command line something like this:

dd if=/dev/whereversd of=/dev/whereeveremmc bs=1M

Unfortunately my SD cards are all over 16GB (except for a C4 that has only booted Armbian) so this method was not possible for me. For anyone else in a similar situation, I was able to inistall Manjaro to the eMMC by booting from the SD, getting the .img.xz file onto the SD and then ran
Code:
xzcat /path/to/manjaro.img.xz | sudo dd of=/dev/emmcp1 bc=1M
I didn't have to extract the .img file, and it took only a few minutes.
  Reply
#45
(05-28-2019, 02:35 AM)erchache2000 Wrote:
(04-14-2019, 07:34 AM)unixfox Wrote: How did you install it on the eMMC? I struggle to do it, I can't find any tutorial about that.

Simple and fast solution is booting from sd and making from command line something like this:

dd if=/dev/whereversd of=/dev/whereeveremmc bs=1M

You need location on dev of your storage before.

Well, I just tried this (And failed, of course). I gathered the correct device names using Parted and use DD just like you described. It was working for a while, then ended with "16GB's copied" and such but also mentioned 'ran out of space on device' but I'm guessing this is to be expected with a simple block-for-block copy command. 

Upon trying to boot from the EMMC drive it will initially try to boot Manjaro (it used to be that ancient KDE Neon install, so something happened at least) but it halts and drops me into an emergency shell:

[Image: full.jpg]

I don't know where or how to continue from here. 

The SD card used is 16GB's just like the internal EMMC (I was warned against using a larger source) but it seems they do differ in size by 0,1GB in favor of the SD card.
  Reply
#46
(06-12-2019, 06:50 AM)trigger Wrote:
(05-28-2019, 02:35 AM)erchache2000 Wrote:
(04-14-2019, 07:34 AM)unixfox Wrote: How did you install it on the eMMC? I struggle to do it, I can't find any tutorial about that.

Simple and fast solution is booting from sd and making from command line something like this:

dd if=/dev/whereversd of=/dev/whereeveremmc bs=1M

You need location on dev of your storage before.

Well, I just tried this (And failed, of course). I gathered the correct device names using Parted and use DD just like you described. It was working for a while, then ended with "16GB's copied" and such but also mentioned 'ran out of space on device' but I'm guessing this is to be expected with a simple block-for-block copy command. 

Upon trying to boot from the EMMC drive it will initially try to boot Manjaro (it used to be that ancient KDE Neon install, so something happened at least) but it halts and drops me into an emergency shell:

[Image: full.jpg]

I don't know where or how to continue from here. 

The SD card used is 16GB's just like the internal EMMC (I was warned against using a larger source) but it seems they do differ in size by 0,1GB in favor of the SD card.

Have you tried using the xcat command I posted above? If the SD is bigger than the eMMC, it should work, and you'll be able to boot into the fresh install within minutes.
  Reply
#47
Added Manjaro KDE (Pinebook1080P micro SD to eMMC Boot) 19.04 on Wiki and Pine64 Installer
  Reply
#48
(06-20-2019, 01:52 AM)pineadmin Wrote: Added Manjaro KDE (Pinebook1080P micro SD to eMMC Boot) 19.04 on Wiki and Pine64 Installer

Color me intrigued. Did you guys do that especially for me? Heart 

On a serious note: What system does this use to install to EMMC? If it's still based on DD I might run into issues, the smallest SD I still have lying around is 16GB, and at that slightly larger (by .1 of a GB) than the internal EMMC, rendering my DD attempts useless.

(06-18-2019, 12:22 PM)tophneal Wrote:
(06-12-2019, 06:50 AM)trigger Wrote:
(05-28-2019, 02:35 AM)erchache2000 Wrote:
(04-14-2019, 07:34 AM)unixfox Wrote: How did you install it on the eMMC? I struggle to do it, I can't find any tutorial about that.

Simple and fast solution is booting from sd and making from command line something like this:

dd if=/dev/whereversd of=/dev/whereeveremmc bs=1M

You need location on dev of your storage before.

Well, I just tried this (And failed, of course). I gathered the correct device names using Parted and use DD just like you described. It was working for a while, then ended with "16GB's copied" and such but also mentioned 'ran out of space on device' but I'm guessing this is to be expected with a simple block-for-block copy command. 

Upon trying to boot from the EMMC drive it will initially try to boot Manjaro (it used to be that ancient KDE Neon install, so something happened at least) but it halts and drops me into an emergency shell:

[Image: full.jpg]

I don't know where or how to continue from here. 

The SD card used is 16GB's just like the internal EMMC (I was warned against using a larger source) but it seems they do differ in size by 0,1GB in favor of the SD card.

Have you tried using the xcat command I posted above? If the SD is bigger than the eMMC, it should work, and you'll be able to boot into the fresh install within minutes.

I have not done so (yet) but if this recent addition to the installer is any good, I might not have to, so I'll try that first Smile.
  Reply
#49
Does GPU accelleration work in Manjaro KDE 19.06?

I've just found the Pinebook 11,6" 1080p OS table and it says "No?" (though it hasn't been updated since December 2018).

For KDE Neon the option says "Yes?", so I'm slightly confused.
  Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  pinebook 1080p crash and fix nano2 2 75 1 hour ago
Last Post: pyrrhumain
  NIxOS installation guide for Pinebook Surehand53 0 30 Yesterday, 03:46 AM
Last Post: Surehand53
  Improve the life of your Pinebook battery by setting charger's voltage limits wlad 0 58 06-11-2019, 02:27 PM
Last Post: wlad
  How can I reliably get battery status on pinebook tillea 5 1,113 06-11-2019, 10:10 AM
Last Post: wlad
  manjaro and qemmu+kvm erchache2000 2 179 06-11-2019, 03:11 AM
Last Post: Skywheel
  pinebook black screen when booting with "different power mode than last used" penzoiders 9 314 06-06-2019, 02:02 PM
Last Post: Surehand53
  Q4OS for PINEBOOK q4osteam 88 23,322 05-27-2019, 09:15 AM
Last Post: Luke
  Wifi I/F on Pinebook 11.6" eblot 2 284 05-19-2019, 04:53 PM
Last Post: Shoananas
  KDE Neon Pinebook remix edition RC image bshah 67 19,525 05-18-2019, 11:44 AM
Last Post: rookieone
  Netrunner 18.03 Idolon for the Pinebook shadeslayer 92 12,278 04-21-2019, 11:37 AM
Last Post: cuvtixo

Forum Jump:


Users browsing this thread: 1 Guest(s)