PADI programming/debugging with STLINK
#1
Has anyone been able to program or debug the PADI with an ST-LINK v2 in SWD/JTAG mode? Using either Arduino or direct from openocd and gdb? I'm connecting SWCLK to GE4, SWIO to GE3 and 3.3v/GND. I load up the WiFi AP Mode example with Board=PADI IoT Stamp and OpenOCD=STLink V2. I've verified the programmer works with the Arduino install works with the STLINK by uploading a program to a STM32 board.

Output of arduino build and upload:
Code:
Sketch uses 271236 bytes (10%) of program storage space. Maximum is 2499639 bytes.
Open On-Chip Debugger 0.10.0
Licensed under GNU GPL v2
For bug reports, read
    http://openocd.org/doc/doxygen/bugs.html
Info : auto-selecting first available session transport "hla_swd". To override use 'transport select <transport>'.
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
adapter speed: 480 kHz
adapter_nsrst_delay: 100
rtl8710_reboot
Info : clock speed 480 kHz
Info : STLINK v2 JTAG v32 API v2 SWIM v7 VID 0x0483 PID 0x3748
Info : using stlink api v2
Info : Target voltage: 3.265469
Info : rtl8710.cpu: hardware has 6 breakpoints, 4 watchpoints
target halted due to debug-request, current mode: Thread 
xPSR: 0x01000000 pc: 0x00000100 msp: 0x1ffffffc
auto erase on
auto verify on
initializing RTL8710 flasher
faultmask (/1): 0x01
sp (/32): 0x20000000
pc (/32): 0x10001000
RTL8710 flasher initialized
/Users/tclarke/Library/Arduino15/packages/padiiotstamp/tools/openocd_tools/0.0.1/rtl8710.ocd:261: Error: invalid command name "file"
in procedure 'rtl8710_flash_write' 
at file "/Users/tclarke/Library/Arduino15/packages/padiiotstamp/tools/openocd_tools/0.0.1/rtl8710.ocd", line 261
the selected serial port at file "/Users/tclarke/Library/Arduino15/packages/padiiotstamp/tools/openocd_tools/0.0.1/rtl8710.ocd", line 261
 does not exist or your board is not connected

Looks like the openocd file might be geared specifically for a different adapter?
  Reply
#2
Seems to be a problem with openocd 0.10.0.. The "file" module was mistakenly disabled for that release.
  Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
Information PADUINO Padi Stamp Photo Blog with SWD and CH340g MarkHaysHarris777 6 1,254 06-01-2019, 10:24 AM
Last Post: cnd
  PADI + OpenOCD + Raspberry PI + Native JTAG burrito 2 366 09-11-2018, 08:44 AM
Last Post: burrito
  Trying to boot first PADI (SOLVED) sgjava 6 555 02-12-2018, 12:34 AM
Last Post: Gary_Cole
  padi performance ktc 3 876 02-16-2017, 06:14 AM
Last Post: kissste
  Powering a 3v PADI and a 5v LED strip basie 5 1,416 01-03-2017, 09:43 PM
Last Post: basie
  PADI - Overclocking to 166MHz works well kissste 4 1,338 11-08-2016, 08:55 PM
Last Post: kissste
  I2S on PADI works well kissste 4 1,380 11-02-2016, 04:26 PM
Last Post: tllim
  Pine64 PADI IOT Stamp Boring 27 7,260 10-17-2016, 05:05 PM
Last Post: kissste

Forum Jump:


Users browsing this thread: 1 Guest(s)