"ROCK 64 STEREO AUDIO DAC ADD-ON BOARD", Is it okay if I turn on the power ?
In the delivered item,
The termination point of the signals "TD+-/RD+-" and center-tap of "pulse trans" are connected to the same node.

*) same node: 1.8v Reference-Voltage
  This node is generated by a newly added parts (regulator) to the published "circuit diagram".

In this state, the value of the resistor that mounted on the board can not be measured accurately.
Because L of "pulse trans" interferes with the measurement of resistance.

Therefore, I removed the resistance from the board, and measured only the removed resistance.
Then the value of resistance was "62Ω", this is the similar value that was generally used.
And this value accords with the numerical value ("062") written on resistance.

Because I was able to confirm the above, my uneasiness point was canceled.
Therefore I turned on a power supply and really operated it.

It worked without a problem.


> Please post a photo so that able to determine whether PINE64 store deliver wrong board to you.

PINE64 store's photo:

Published schematic:

Delivered Item's photo:

The reason why I bought this board is as follows.

As can be understood by referring to the following thread,
Nobody made it according to the published circuit diagram and succeeded in its operation.

"WARNING: internal 10 | 100 PHY requires magjack hardware!"

My doubts are as follows
1). Why does it work with this "circuit diagram" ?
2). Why selling products that do not work ?
Because I thought that the fact must be either of the above.
My purpose of purchase was to confirm the above.

So, I had the opportunity to purchase "RockPro64", so i bought this product together.
After receiving the product, and seeing it, my doubts was solved immediately.

The received item is clearly different from the picture of the product being published and its circuit diagram.
And a lot of parts were added to the "EtherNet" related part of the received item.

… My estimation was a mistake. …
  The result was neither of the above doubt "1)" / "2)".

To unexpected things,
  The product that is currently on sale is different from "published photo / circuit diagram".
The fact was due to the above reasons.

  It is obvious that it will not work, even if it is created according to the published circuit diagram.

*) Finally.
  I present the "circuit diagram" of item that I actually make and worked well, and the parts used for it as examples.

RJ45-JACK(with pulse trans)


Parts used for "ROCK 64 STEREO AUDIO DAC add-on board" are …
  The terminating resistor is "62 Ω".
  The manufacturer of the regulator(1.8v) is unknown.
  There is no LED display function of "EtherNet".

Attached Files Thumbnail(s)

Messages In This Thread
RE: "ROCK 64 STEREO AUDIO DAC ADD-ON BOARD", Is it okay if I turn on the power ? - by t4_4t - 01-07-2019, 05:51 PM

Possibly Related Threads…
Thread Author Replies Views Last Post
  Alternative power supply ju0n 0 89 09-06-2022, 02:46 AM
Last Post: ju0n
  Audio Pot Board Questions vfr400racer 3 680 08-11-2022, 06:34 PM
Last Post: Roberto2020
  Rock64 4K60P HDR Media Board Computer 64 bit MarkHaysHarris777 8 13,204 07-14-2021, 11:52 PM
Last Post: jontumontu
  RS-485 CAN HAT Rock won’t boot gnvdude 1 2,050 01-10-2021, 05:15 PM
Last Post: as365n4
  Help connecting a dvb board in the right gpio pins cosmodeal 0 1,539 11-11-2020, 12:48 PM
Last Post: cosmodeal
  Power Supply and Sinks for multi-Rock64 env Davo-CC 1 3,604 01-02-2020, 02:26 PM
Last Post: dpgraham
  power connector type please AlexS 1 2,539 08-31-2019, 08:27 AM
Last Post: tllim
  Rock64 stereo audio dac add-on board with RockPro64 Tim13 1 2,680 07-08-2019, 07:15 PM
Last Post: tllim
  Using a stronger power supply myn4m3 1 2,111 06-23-2019, 05:01 PM
Last Post: Rocklobster
  Rock64 Stereo Audio DAC add-on board Hukmut 3 4,201 06-15-2019, 07:56 AM
Last Post: MiiCode2

Forum Jump:

Users browsing this thread: 1 Guest(s)