Unable to boot from SPI
#1
So I had flashed my SPI via SD card method, I waited until the LED goes blinking and turned off the device, and then I flashed my USB 3.0 drive to OMV with Etcher in Windows, and now it isn't booting at all! HDMI has no signal after I started the booting, neither was there any blinkings anymore, I have very limited hardware debugging skill and I simply want to know how to restore access to my Rock64, thank you.
  Reply
#2
Strange. So I was able to access the OMV web panel in my bet to check the DHCP list of my router, but there was no visible HDMI output. I checked the cable is completely fine, I'm very confused right now...
  Reply
#3
Any help? I need HDMI to debug certain stuff...
  Reply
#4
(06-29-2018, 06:16 AM)stevefan1999 Wrote: So I had flashed my SPI via SD card method, I waited until the LED goes blinking and turned off the device, and then I flashed my USB 3.0 drive to OMV with Etcher in Windows, and now it isn't booting at all! HDMI has no signal after I started the booting, neither was there any blinkings anymore, I have very limited hardware debugging skill and I simply want to know how to restore access to my Rock64, thank you.

If you thinks is cause by SPI Flash implementation, you can ease SPI Flash using below link:

http://wiki.pine64.org/index.php/NOOB#Er...riting_SPI
  Reply
#5
(07-22-2018, 07:26 AM)tllim Wrote:
(06-29-2018, 06:16 AM)stevefan1999 Wrote: So I had flashed my SPI via SD card method, I waited until the LED goes blinking and turned off the device, and then I flashed my USB 3.0 drive to OMV with Etcher in Windows, and now it isn't booting at all! HDMI has no signal after I started the booting, neither was there any blinkings anymore, I have very limited hardware debugging skill and I simply want to know how to restore access to my Rock64, thank you.

If you thinks is cause by SPI Flash implementation, you can ease SPI Flash using below link:

http://wiki.pine64.org/index.php/NOOB#Er...riting_SPI

I'm having the same problem after using the U-boot erase program.  I also waited until the LED started a continuous blinking.  I then turned the machine off and now can't read from the SPI.  I had been using the USB for SSDs and µSD holders.  Now there is no response ... ability to read anything.  The Internet port also appears to be dead.  I have a number of good builds, but the won't boot.
  Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
Bug u-boot (forks) status mcerveny 13 1,916 08-08-2020, 03:55 PM
Last Post: CameronNemo
Sad No boot, garbage console text and blinking red light ... jean_bruder 2 148 07-19-2020, 08:37 AM
Last Post: jean_bruder
  No boot up after power on Whoopsadaisy 2 252 05-26-2020, 11:24 PM
Last Post: Whoopsadaisy
  Graphical boot manager john3voltas 0 175 03-25-2020, 02:27 PM
Last Post: john3voltas
  doesn't boot, no video cjyar 7 643 11-15-2019, 03:45 PM
Last Post: ab1jx
  No Boot, Red Green and White flash at 1 sec intervals wesleykonrad 2 557 01-28-2019, 11:54 PM
Last Post: wesleykonrad
  boot priority - has precedence changed? jovval 1 1,129 09-22-2018, 02:02 AM
Last Post: mcerveny
  Enable I2C, I2s, SPI in boot-config file? HelgeMK 3 2,153 08-14-2018, 10:59 AM
Last Post: pas059
  New ROCK64 doesn't boot p3ntium 18 2,127 06-03-2018, 06:06 PM
Last Post: Rocklobster
  boot logs shows chinese ip trying to login ssh i69fstop 6 699 06-02-2018, 07:25 PM
Last Post: Z80

Forum Jump:


Users browsing this thread: 1 Guest(s)