Pinebook SDIO gpio control using SD card slot blog post
#13
(08-23-2017, 06:32 PM)MarkHaysHarris777 Wrote:
(08-23-2017, 06:01 PM)machinehum Wrote: This is a really cool idea, thanks for sharing.

The last post people are talking about issues with the current solution - I want to start a little opensource project designing a breakout for this, I can label all the pins and incorporate whatever else would be useful, LEDs, sensors, headers, etc...

Seeed can manufacture PCBs that are 0.6mm & 0.8mm, I believe a post above said they must not be thicker than 0.75mm, but the height of a uSD card is ~1mm - would the 0.6mm or 0.8mm be best?


I can also send out some free board for people. They'll be dirt cheep.

Let me know if anyone is interested in helping out (feedback, suggestions, etc...) we can set up a time on the IRC

~wlkr


I'm definitely interested in providing input !   Wink

I think .8mm  would be pressing it;  but, really,  the best way to spec the end of the board is that it should look and be precisely identical (exactly) with a micro SD card !  --not thicker,  not thinner;

Also, it needs to be able to activate the spring latch correctly of a push-push slot like the one in the Pinebook.

The Sparkfun board works but is sloppy in both regards to the above two requirements.  The other brand does not work at all because its too thick to enter the slot... it won't even enter the slot of a carrier outside the Pinebook !

The wikipedia says they're 1mm thick? So I'm not sure why the 1mm thick PCB didn't work at all. It's possible they didn't pull the solder mask back far enough, so the FR4 is 1mm + solder mask > 1mm - is it close? or completely out to lunch?

It's difficult to get PCB's to an "exact" thickness, typically you just get whatever your CM offer.

Spring latch should be easy to do.

Do you have any other input? or is  a pure breakout good enough? I think it would be cool to get an STM32 or ATMEGA onboard as well, then you could piggyback of their peripherals and communicate over SPI. I think the key would be to keep it really small, so you can bring it around.


Messages In This Thread
RE: Pinebook SDIO gpio control using SD card slot blog post - by machinehum - 08-23-2017, 08:21 PM

Possibly Related Threads…
Thread Author Replies Views Last Post
  pinebook 1080p power/barrel connector/cable cel 0 497 08-03-2023, 11:43 AM
Last Post: cel
  eMMC compatible with Pinebook leperotero 0 1,321 07-19-2022, 07:15 AM
Last Post: leperotero
Heart [solved] Anyone selling their Pinebook? feyn 0 1,168 07-11-2022, 03:38 PM
Last Post: feyn
  Move PB Pro eMMC 128 GB to Pinebook 11 1080p petet0n76 1 1,565 06-07-2022, 10:35 PM
Last Post: tllim
  UART switch Pinebook 11.6" irongarment 3 3,219 01-03-2022, 03:28 AM
Last Post: kqlnut
Exclamation "6" Key direly needed for 11" Pinebook Corkonian 1 2,532 09-25-2021, 12:03 AM
Last Post: tllim
  SD card read/write troubles jezek 1 2,922 03-26-2021, 09:27 AM
Last Post: jezek
  Pinebook 14 " Battery Swollen/Bulged billjon 1 3,540 01-13-2021, 11:03 AM
Last Post: barray
  touchpad on pinebook issues? ron_burgundy 14 13,510 12-19-2020, 06:55 PM
Last Post: ron_burgundy
  CH341 boards for GPIO xalius 1 4,067 11-22-2020, 10:50 AM
Last Post: pinephonenewbee

Forum Jump:


Users browsing this thread: 1 Guest(s)