Hi everybody,
I bought the pine64 2GB version, than I burn the 'Debian Linux Jessie with Mate GUI Image' on the SD card according to the wiki page.
After powering the board, there is nothing on PC monitor, no action, no output. The system boots fine, serial console by EXP connector works, SSH by 'Putty' works.
Please can you advice me what's wrong? My monitor doesn't have HDMI but have DVI. To connect it I use HDMI-DVI adaptor like this: http://www.officeworks.com.au/shop/offic...-cohddviad
I used to use this adaptor with same PC monitor and with Raspberry PI and it was working.
When I use it with pine64 and plug and unplug the monitor cable I get message (on serial console) like this:
[ 55.600051] hdmi_clk_disable_prepare()L176
[ 62.557231] hdmi_clk_enable_prepare()L161
Also startx doesn't work:
debian@pine64:~$ sudo startx
[sudo] password for debian:
X.Org X Server 1.16.4
Release Date: 2014-12-20
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.16.0-4-arm64 aarch64 Debian
Current Operating System: Linux pine64 3.10.102-0-pine64-longsleep #7 SMP PREEMP T Fri Jun 17 21:30:48 CEST 2016 aarch64
Kernel command line: console=tty0 console=ttyS0,115200n8 no_console_suspend disp .screen0_output_mode=720p60 earlycon=uart,mmio32,0x01c28000 mac_addr=36:c9:e3:f1 :b8:05 root=/dev/mmcblk0p2 ro rootwait
Build Date: 11 February 2015 01:19:23AM
xorg-server 2:1.16.4-1 (http://www.debian.org/support)
Current version of pixman: 0.32.6
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.1.log", Time: Sat Nov 12 14:40:10 2016
(==) Using config file: "/etc/X11/xorg.conf"
(==) Using system config directory "/usr/share/X11/xorg.conf.d"
modprobe: FATAL: Module g2d_23 not found.
modprobe: FATAL: Module mali_drm not found.
modprobe: FATAL: Module sunxi_cedar_mod not found.
SunxiMaliDRI2_Init: drmOpen failed!
I bought the pine64 2GB version, than I burn the 'Debian Linux Jessie with Mate GUI Image' on the SD card according to the wiki page.
After powering the board, there is nothing on PC monitor, no action, no output. The system boots fine, serial console by EXP connector works, SSH by 'Putty' works.
Please can you advice me what's wrong? My monitor doesn't have HDMI but have DVI. To connect it I use HDMI-DVI adaptor like this: http://www.officeworks.com.au/shop/offic...-cohddviad
I used to use this adaptor with same PC monitor and with Raspberry PI and it was working.
When I use it with pine64 and plug and unplug the monitor cable I get message (on serial console) like this:
[ 55.600051] hdmi_clk_disable_prepare()L176
[ 62.557231] hdmi_clk_enable_prepare()L161
Also startx doesn't work:
debian@pine64:~$ sudo startx
[sudo] password for debian:
X.Org X Server 1.16.4
Release Date: 2014-12-20
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.16.0-4-arm64 aarch64 Debian
Current Operating System: Linux pine64 3.10.102-0-pine64-longsleep #7 SMP PREEMP T Fri Jun 17 21:30:48 CEST 2016 aarch64
Kernel command line: console=tty0 console=ttyS0,115200n8 no_console_suspend disp .screen0_output_mode=720p60 earlycon=uart,mmio32,0x01c28000 mac_addr=36:c9:e3:f1 :b8:05 root=/dev/mmcblk0p2 ro rootwait
Build Date: 11 February 2015 01:19:23AM
xorg-server 2:1.16.4-1 (http://www.debian.org/support)
Current version of pixman: 0.32.6
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.1.log", Time: Sat Nov 12 14:40:10 2016
(==) Using config file: "/etc/X11/xorg.conf"
(==) Using system config directory "/usr/share/X11/xorg.conf.d"
modprobe: FATAL: Module g2d_23 not found.
modprobe: FATAL: Module mali_drm not found.
modprobe: FATAL: Module sunxi_cedar_mod not found.
SunxiMaliDRI2_Init: drmOpen failed!
